similar to: Cross-compiling for ARM Linux

Hi there, I've just started to work with the great speex encoder on ARM9-based embedded platform. This is my configuration: CPU: Cirrus Logic EP9315 @ 200 MHz (ARM920T) o.s.: Linux 2.6.9-rc2-ep93xx GCC: gcc version 3.3.3 (DENX ELDK 3.1 3.3.3-10) without MaverickCrunch support ogg library: 1.0 speex command line configuration: ./configure --enable-fixed-point --enable-arm4-asm The code is

[CCing the libguestfs mailing list - as Rich responded on IRC about your question on timeout.] On Sun, Feb 21, 2016 at 10:07 PM, Thomas Kee <xsited@yahoo.com> wrote: > Hi Kashyap, > > Thanks for offering to help. The day job caused a pause and it took me an > hour to reassert where I was in the process. I usually hang out on freenet > as xsited. I am still reading the

Hi I want to port speex to my pocket PC iPAQ1945 which has a Samsung processor 2410, an ARM9-based processor. I would like to write the specific optimized code for this chip. I had some experience at DSP chip and fixed-point coding but know nothing about embedded system and ARM. Could someone tell me some hint how to write optimized code for this pocket PC. If you can give me some links that will

Hello everyone, I just ordered one of these: http://www.marvell.com/products/embedded_processors/developer/kirkwood/sheevaplug.jsp Just over $110 with shipping but they are expecting the price to come down quite a bit: - 1.2Ghz ARM5 - 512MB RAM - Multiple flash storage options - Gigabit ethernet - USB 2.0 - 5 watt power usage They probably won't be shipping until late March but I

Hi, I'm trying to get speex working on an ARM board (ARM926EJ-Sid(wb) core, ARM 5TE architecture) and getting segfaults if build with "--enable-fixed-point --enable-arm5e-asm" options. If I use just "--enable-fixed-point", then it runs fine, but once I add "--enable-arm5e-asm" it start crashing (I use testenc to test it). Further investigation showed, that it

Hi, I am attempting to port the speex library to TI Davinci DM35x Family. My questions are: 1. What is the best ./configure option for it? Is it ARM5e / ARM4 ? when I tried these two the during the compiled a warning "I suppose you can have a [ARM4/ARM5E/Blackfin] that has float instructions?" 2. is there any available demos for the echo cancellation because I can get it

I'm running FreeBSD 8 on a Sheevaplug (ARM5 processor) I compiled and installed Samba 3.3.9 from ports using defaults and defaults for dependencies. I left the smb.conf file untouched, ran testparm and immediately received the coredump. The same happens running smbd and nmbd. Can anyone help me resolve? http://old.nabble.com/file/p26879957/testparm.core.gz testparm.core.gz -- View this

Hi all, I'm trying to use libspeex 1.1.10 on an ARM926EJ-Sid(wb) rev 3 (v5l). I executed the speexenc and speexdec test files and they can encode and decode. But I'm getting 95% of cpu utilization on the codification and 44% on the decodification. I saw in the post: http://lists.xiph.org/pipermail/speex-dev/2005-June/003485.html that this version of speex works fine on ARM

Hi, I am using a cross compiler to compiler for the arm5 architecture. For this architecture it is not allowed that a destination register is also used as source register. In 2007 a patch was discussed at the mailing list, however my compiler still is producing this result. Does anyone know if this patch is actually applied? * I use the following arguments: llvm-gcc -mfpu=vfp -mlittle-endian

Hi there. The attached patch adds If-Then (IT) instructions to the ARM inline assembly in Speex, allowing it to compile in Thumb-2 mode. Traditional 32 bit ARM instructions can be conditionally executed depending on which flags are currently set. Thumb-2 requires an 'IT' instruction instead that affects up to the next four instructions. Note that when compiling for ARM 32, IT

I am very new to linux and openSSH ,, i am trying to compile openssh for jungo openrg IXP45. but while configuring i am getting following error,, hecking for libgen.h... yes checking for getspnam... yes checking for library containing basename... none required checking for deflate in -lz... no configure: error: *** zlib missing - please install first or check config.log *** if anybody will me

wouldn't it be a good idea to have the libraray available as a binary for non-PC platforms like the PocketPC, Symbian and Mac? i am suggesting this as it will allow the developers to go ahead and program to an interface while the development continues. there are builds for symbian, pocket pc and linux already in the tar ball. putting their binaries on the download section will probably

Hi, I tried the same options suggested in your post and the problem continues. What do you suggest? 2005/9/15, Jean-Marc Valin <Jean-Marc.Valin@usherbrooke.ca>: > Hi Eduardo, > > All I can say is that the timings you have are a bit odd. What > optimizations options are you using (I suggest -O3)? Also, perhaps you > can try --enable-arm4-asm just in case. I've had the

Hi everyone, I'm planning on releasing Speex 1.2beta2 in the next few days. I'd appreciate if everyone could try and test the current svn to make sure no bug crept in for your favourite plarform/application. Cheers, Jean-Marc

Hi, all, I am porting speex on ARM7TDMI, I have done some optimization, the result is that the encoder and decoder need about 60 MCPS for 5.96kbps bitrate and complexity 0. Can someone give me informtion about Speex optimization on ARM7? Another question, my ADC and DAC are 12 bits, but Speex codec is 16bits, Did someone try to modify speex to 12 bits? I think if I modify speex to 12 bits, the

Hi All, I'm trying to build speex for the mini2440 board, with this toolchain: http://www.friendlyarm.net/dl.php?file=arm-linux-gcc-4.3.2.tgz because speex is a dependency of the sip softphone 'linphone'. The 'configure' string I'm using is this: ./configure --prefix=/usr --host=arm-linux --with-gnu-ld --disable-static --enable-fixed-point --enable-arm-asm Other

Hello, Chuck. You wrote Tuesday, May 16, 2006, 6:03:14 PM: C> /usr/lib/gcc/i686-pc-cygwin/3.4.4/../../../../i686-pc-cygwin/bin/ld: BFD C> 2.16.91 C> 20050610 assertion fail C> /netrel/src/binutils-20050610-1/bfd/cofflink.c:1926 C> make[2]: *** This is a bug in binutils also seen in mingw32 build. :( I've sent bug report to binutils bugzilla this weekend. Hope, this will be

Hello, Reid. You wrote Tuesday, May 16, 2006, 11:13:19 PM: RS> What does the assertion say? The same text, as in the original e-mail: <=cut=> /usr/lib/gcc/i686-pc-cygwin/3.4.4/../../../../i686-pc-cygwin/bin/ld: BFD 2.16.91 20050610 assertion fail /netrel/src/binutils-20050610-1/bfd/cofflink.c:1926 <=cut=> This assertions is in big function named: bfd_boolean

sshd disconnects openssh-4.1p1 on IBM p690 AIX 5200-05 using: openssl-0.9.7g zlib-1.2.2 openssh-4.1p1 CC="gcc -O0 -maix64" ./configure #- 64-Bit !!! Compiles ok. ssh works fine. sshd starts, accepts password, user authenticated and then disconnects. Debug log of both sshd and trying-to-connect client (3.9p1-3.2 on Linux) are enclosed. For test purposes por 3333

The attached patch eliminates some warnings while compiling for ARM4 targets. It also simplifies the asm constraints a bit. Now we can use the ARM4 optimisations when compiling for PortalPlayer targets in Rockbox. Cheers, Dan -------------- next part -------------- A non-text attachment was scrubbed... Name: speex_arm4.patch Type: text/x-diff Size: 1550 bytes Desc: not available Url :