similar to: Programming questions

I'm only doing one frame using speex_encode_int greatly simplifies my code I'm not sure why the sample I was working off of was converting the shorts to floats then calling the other encode/decode methods. Based off of your suggestions I tried the following but I get the same result. virtual Enigma::u8* Encode(Enigma::u8* inputBuffer,size_t inputSize, size_t& outputSize) {

Thank you for such a quick response. The only reason I started with Char buffers is because WaveIn and WaveOut on Windows XP accept/emit WAVEHDR structures, which store audio data in LPSTR, which is Char*. typedef struct { LPSTR lpData; DWORD dwBufferLength; ... } WAVEHDR; When I was going from Char to float and back looked very wrong to me as well, but I was just not

Hi All, Almost all my question is in the subject. I have written the following small program and I get an error message when I try to use SPEEX_GET_QUALITY. This functionality seems not to be used in speexenc.c or speexdec.c. I would appreciate any hints. best regards, Alain Aubord ---------------------------test.c--------------------------------------- #include <stdio.h> #include

>> you are better off using the vogg orbis codec. speex is meant >> specifically for telephonic voice. it takes a single human voice and >> compresses it well. it cannot handle muliple voices or music very well. >That part is true, so of course it depends on the application. I guess I >should have added that for most applications, 16 kHz is recommended >instead of 44.1

Alright noted, I changed me code so that the state is created in the constructor and destroyed in the destructor of the object. However I'm still getting the same issue although I'm sure that would have bit me sooner or later. The new code is as follows. virtual Enigma::u8* Encode(Enigma::u8* inputBuffer,size_t inputSize, size_t& outputSize) { short *in=(short*)inputBuffer;

Hi all, i've to encode voice from a voicemodem. I choose speex 1.0.5 for its quality in voice encoding. I've tried to implement an encoder but unsuccesfully. Here's my code: /* ============ SPEEX stream ENCODER ============================================ */ int SPEEX_EncodePCM(struct _IDA_ClientSocket *IDA,char *buffer,unsigned char *PCM,int num_samples) { /* buffer point to the

I have (finally) posted my Speex wrapper classes. They are at: http://www.grandgent.com/spx/tgAudioCodec.zip I followed your recommendations and they worked fine with 1.1.0. However, I'm still having the same problem with 1.1.7 that I had the last time I tried to upgrade. I'm using the same code with both versions, except for calling speex_encode_int instead of speex_encode, and

First let me introduce myself: Sr Computer Scientist 20+ yrs SW/HW development Audio Rookie < 60 days Intel based computer Soundblaster 128 PCI Linux Fedora Core 2 ALSA - Advanced Linux Sound Architecture ALSA provides the audio and MIDI functionality to the Linux operating system as of Fedora Core 2 and is the future of Linux (so I have been told) http://www.alsa-project.org/ I have read

Hi, I'm using speex 1.1.10 and writing a program similar to sampleenc. I need to use the fixed point library as I'm eventually porting to ARM processor but I encountered a problem with speex_encode_int(), which I used in place of speex_encode(). I gave it a short instead of a float (manual says it takes a short for the audio - 2nd parameter) but the compiler says it could not convert the

Hi All, I am quite new to voice encoding and to Speex library. I have some programming questions that I am not able to answer even after having read the documentation (from the start to the end an from the end to the start) and by reading the sample code (provided in the documentation) and the speexdec.c and speexenc.c programs. I am currently working on an interface between Java code and

Hi All, I'm very new to speex and in fact handling audio at all, it seems I have run in to a problem I seem unable to fix. I'm trying to take audio from a microphone using alsa, then encode it as speex and save to disk. I have been wondering if it has something to do with endian type, but speexenc and speexdec works fine. Currently I have the following setup: Platform:

Changing from using floats to shorts did fix the high pitched tone problem. I'm having other problems but I'll look into it more first. SteveK wrote: > > On May 21, 2006, at 6:33 PM, Kevin Jenkins wrote: > >> When I just copy the microphone input buffer to the output buffer the >> sound plays OK. But if I encode and decode the buffer through Speex I >>

how many calls can I make to speex_encode_int before calling speex_bits_write? Can I stuff 10 frames? - farhan

Hello, I know my question has been asked before because I spent the last week searching the web for how to use Speex in combination with WaveIn/WaveOut and I ran into a few posts, but none of them answer the question. There is still a lot of confusion how to use WaveIn/WaveOut and Speex by junior developers such as myself. Even after examining code for SpeexDec and SpeexEnc, I cannot get clear

Hi, I am developing my own file format and I have a question about the standard encode method: speex_encode_int(st, raw, &bits); nbBytes = speex_bits_write(&bits, s+1, 255); My question is : Will nbBytes ever be 0 ? (even with an empty frame of all 0's passed to speex_encode_int) In other words is it possible for the encoder to return a compressed bit stream that is 0

On Wed, Nov 17, 2004 at 09:05:05AM +0900, Jean-Marc Valin wrote: > Why do you want your app to with with 1.1.4 in the first place. It's a > old unstable version and its API has been changed since then. > ie. Flavio, please upgrade to the recent 1.1.6 release. In your code, you will need to change the follwing line (for the 1.1.x build only): > > /* Encode the frame */

On Mon, Apr 19, 2004 at 02:46:44AM -0400, Jean-Marc Valin wrote: > OK, I'll try to do *something* about it. It'll be either "support the > 1.0 ABI" or "make sure the link will break". While the former would be > nice, I'm not sure I want to really want to force 1.2 to have the same > ABI as 1.0.x. More on this when I have some time to think about it.

Hi, i know this question has already been asked, i've checked mailing list logs but ... I didn't figure out the solution for my question. I want to use basic functionnality of speex, only VAD, no pre/post filter, even no VBR. But i *really* want to use less mem/cpu i can. So in which format should i pass data to speex_encode(_int) , float or short ? I quickly looked at the source code

Hi everyone, Our team is working on a realtime voice communication application. We are using openAL 1.1 to capture the samples and then encode them using speex. On the remote machine we decode the samples and play them using openAL again. Capture and play formats for the samples is AL_FORMAT_MONO16 and frequency is 22050. we are using wide band encoding/decoding. The encoding sample

This patch will export new speex functions in the generated library, such as speex_encode_int as well as the preprocessor, echo-cancellation and jitterbuffers. The ordinals used matches the 1.1.6 release from the speex.org website, so any new library created with this def file should be binary compatible with that one. -------------- next part -------------- Index: speex.def