similar to: Encoding frame limit

Hi, I am using speex 1.2beta2 on a narrowband 16-bit, 8khz system that has a severe program space problem and will not fit speex in its normal operation. In an attempt to shrink speex I placed a breakpoint in every function and ran a decode and encode and removed the breakpoints that I hit. in the functions that had a breakpoint that I didn't hit I commented out those functions (as well as

for the bits init I am using speex_bits_set_bit_buffer and I don't use the write to or read from because the data is already in the buffer I am reading from and I am writing to the final buffer so I don't need to move arrays around. what part is the vocoder part of the decode? Thanks for your help! -Mike >>> Jean-Marc Valin <jean-marc.valin@usherbrooke.ca> 08/06/07

I'm glad to hear that my data size can be shrunk considerably, however I do not know the minimum values that I would set the static arrays to be. I hate to be a bother but could you tell me the minimum values for these arrays/structures in the state structure? Thanks! encode: stack winBuf excBuf swBuf lagWindow old_lsp old_qlsp mem_sp mem_sw mem_sw_whole mem_exc mem_exc2 pi_gain pitch

Hi All, I'm very new to speex and in fact handling audio at all, it seems I have run in to a problem I seem unable to fix. I'm trying to take audio from a microphone using alsa, then encode it as speex and save to disk. I have been wondering if it has something to do with endian type, but speexenc and speexdec works fine. Currently I have the following setup: Platform:

Hi, I am using the speex 1.0.4 library from Windows. I have posted my problem before but didn't get a solution. I am doing an VOIP project in which i am recording sound and streaming it to the peer. I wanted to encode and decode wav files that brought me to this site. I am recording sound in the following format:- m_WaveFormatEx.wFormatTag = WAVE_FORMAT_PCM;

Hi all, i've to encode voice from a voicemodem. I choose speex 1.0.5 for its quality in voice encoding. I've tried to implement an encoder but unsuccesfully. Here's my code: /* ============ SPEEX stream ENCODER ============================================ */ int SPEEX_EncodePCM(struct _IDA_ClientSocket *IDA,char *buffer,unsigned char *PCM,int num_samples) { /* buffer point to the

I've targeted Speex to run under eCos with Thumb interworking using arm-elf-gcc 3.3.3 I'd written a small test case to verifiy the operation: #include <speex/speex.h> void speex_test(void) { SpeexBits bits; unsigned int frame_size; void *enc_state; float *speex_frame; cyg_uint64 t1, t2; int i; speex_frame = (float *)0x00030000; /* Address of Speex data

Hi All, I am a Speex novice but trying to use Speex in my Doctoral thesis. I installed Speex, was able to encode and decode files. Right now, I want to write my own cpp program that handle Speex-files. I tried to compile and run the two sample programs that come with the documentation (after having insalled the speex-devel-1.0.5-1.i386.rpm). However, when I compile. gcc sampleenc.cc Here is

I'm completely new to speex and I'm having issues adding it to my application. I can pass raw PCM and that works fine so I know my transmission code is fine however when I try to encode/decode using speex I get noise almost like a whining/buzzing sound. I'm sure it's and issue in my code but I'm not sure where to start looking other then my gut tells me I'm not sizing or

I have problem with coding and decoding. I record voice from mic coding and write to file. And when I read from file and put it on sound card it's terrible sound. Have sameone can help me? #include <speex.h> #include <stdio.h> #include <fcntl.h> #include <sys/ioctl.h> #include <sys/soundcard.h> /*The frame size in hardcoded for this sample code but it

I have (finally) posted my Speex wrapper classes. They are at: http://www.grandgent.com/spx/tgAudioCodec.zip I followed your recommendations and they worked fine with 1.1.0. However, I'm still having the same problem with 1.1.7 that I had the last time I tried to upgrade. I'm using the same code with both versions, except for calling speex_encode_int instead of speex_encode, and

Hello, When I decode a recoded sound encoded by speex, it has too much noise. The noise is "slightly" reduced if I set the quality to 10. How do I get rid of this noise? The code is as follows. For encoding . state = speex_encoder_init ( &speex_nb_mode ); tmp = 7; speex_encoder_ctl ( state, SPEEX_SET_MODE, &tmp); // set quality tmp = 10; speex_encoder_ctl ( state,

Alright noted, I changed me code so that the state is created in the constructor and destroyed in the destructor of the object. However I'm still getting the same issue although I'm sure that would have bit me sooner or later. The new code is as follows. virtual Enigma::u8* Encode(Enigma::u8* inputBuffer,size_t inputSize, size_t& outputSize) { short *in=(short*)inputBuffer;

I'm getting garbled playback with decoded fragments and I'm hoping someone here can point me in the right direction to correcting the problem. Essentially I'm capturing audio from the microphone. I stream it over the net, but for testing purposes with this API I'm just grabbing the whole chunk and encoding / decoding it right away and then updating the sound buffer for

Jean-Marc Valin <Jean-Marc.Valin@USherbrooke.ca> wrote: > > > 1) Supporting the various versions of Speex is a nuisance, mainly > > because there is no #define or API call to query the version. > > It is possible to get the version using speex_lib_ctl(int request, void > *ptr). Possible requests are SPEEX_LIB_GET_MAJOR_VERSION, > SPEEX_LIB_GET_MINOR_VERSION,

Hi, I'm very sorry if those questions are repeated over and over, but I cannot find a solution on the net. I try to use speex to encode/decode voice to send over the network. My doubts are: 1. The Bits_Per_Sample I use, are independent from the speex encoding/decoding? (So...can I use 8, 16, 24..and so on?) 2. If I have this situation: SAMPLE RATE.....: 8000 BITS PER SAMPLE.: 16

Hello, I'm trying to use the speexlib but I just can't do it. I've made just like the example (on the site) says. Some times I get SIGFAULT. Also, I'm reading the input_frames from /dev/dsp (directly). What is missing here? speex_bits_init(&bits); enc_state = speex_encoder_init(&speex_nb_mode); speex_encoder_ctl(enc_state, SPEEX_GET_FRAME_SIZE, &frame_size);

Hi i'm developing a sort of VoIP application for my ipaq using speex... I'm still at beginning and i have many problems encoding and decoding my wav files....output is only noise! Why? I'm using Libspeex 1.1.3, Embedded VisualC++ 3.0, Ipaq 3850(206 MHz Intel® Strong ARM 32-bit RISC Processor) PocketPC 2002 (Windows CE 3.0). Libspeex is complied with the definition of

It seems that speex (speex 1.0.4 on OSX 10.3.9) is writing over the input buffer (with what looks like a sine wave). Included below is a short program that demonstrates the problem. Is this a bug, or am I doing something wrong? I don't see this behavior mentioned in the docs. I don't really need the input buffer, but I'm guessing this problem is related to a high pitched sound

Hi, Can someone please help me with my problem below. Any suggestions is appreciated. thanks, Carine ----- Original Message ---- From: Carine Liang <carineliang@yahoo.com.sg> To: speex-dev@xiph.org; speex-dev@xiph.org Sent: Tuesday, 31 October 2006 1:05:49 PM Subject: [Speex-dev] Integrating speex with VideoNet application: Constant background noise Hi, I am developing a peer-to-peer