similar to: chronyd vs ntpd on SambaAD ?

Displaying 20 results from an estimated 1000 matches similar to: "chronyd vs ntpd on SambaAD ?"

2019 Oct 27
1
chronyd vs ntpd on SambaAD ?
On Thu, 2019-10-24 at 16:27 +0100, Rowland penny via samba wrote: > On 24/10/2019 16:10, S?rgio Basto via samba wrote: > > Hi, > > As Centos 7 and Fedora defaults to chronyd [2] , should I use ntpd > > for > > some reason [3] ? I based my configurations on [1] which use ntpd > > ... > > but I thinking change for chronyd , change ntp deamons could outage >
2016 Dec 27
2
chronyd configuration as a local ntp server
This is for centos 7 that has chronyd 2.1.1 I am looking into how to use chronyd as my local ntp server. On my old servers with ntpd I had local access control lines like: restrict 192.168.128.0 mask 255.255.255.0 nomodify notrap But in looking for documentation on chronyd I did not find anything on this at: https://chrony.tuxfamily.org/doc/2.1/manual.html In the actual /etc/chronyd.conf
2016 Dec 27
2
chronyd configuration as a local ntp server
AFAIK the only thing needed to make your host an NTP server using chrony is to set the allow line to the network address in CIDR format of the network you want to be served, and uncomment it. The restart chronyd. You also need to ensure that port 123 (NTP) is open to your internal network on your filrewall. I have a CentOS 6 box that is an NTP server for my network. CentOS 7 works the same
2016 Dec 30
1
chronyd configuration as a local ntp server
Robert, If your NTP server will be on 7/24, I would uninstall chrony and install ntpd which is still included in CentOS 7. Configure as usual. For the differences between chrony and ntpd reference: http://thegeekdiary.com/centos-rhel-7-chrony-vs-ntp-differences-between-ntpd-and-chronyd/ Essentially, chrony is more for laptops with intermittant network connections, and ntpd is better suited to
2015 May 24
4
Systemd
On 5/24/2015 12:22 PM, Gordon Messmer wrote: > On 05/24/2015 11:41 AM, Kirk Bocek wrote: >> to activate your selected daemon. I just used the new systemd commands, >> thinking that would be enough. So I tried that and rebooted. Nope, same >> problem: > > chronyd and ntpd both use UDP port 123, so each will terminate the > other when it starts. If both are enabled,
2019 Nov 17
4
I can't get Win10 clients to sync time with the DC
On 17.11.2019 15:58, Sonic wrote: > On Sun, Nov 17, 2019 at 5:37 AM Viktor Trojanovic <viktor at troja.ch> wrote: >> I'm not sure I understand your setup. It seems like you are running >> Chrony on the host only and you just share the socket with the >> container, no chrony running there. > Yes, you have it correct. That's exactly what I'm doing. >
2017 Jan 19
1
System Time Jumps During Boot on CentOS 7
Hi All, Just noticed a funny time jump on a testing CentOS 7 VM. Specifically the system time jumps around by a few hours during system boot. The below is a selection from /var/log/messages during boot: Jan 19 12:49:57 arr-data-dev chronyd[716]: Frequency -0.829 +/- 0.007 ppm read from /var/lib/chrony/drift Jan 19 12:49:57 arr-data-dev polkitd[720]: Started polkitd version 0.112 Jan 19
2017 Apr 20
1
startup process that rebuilds aliases.db?
My Centos7 system does not have a battery for the clock (like most armv7 SOCs), thus I rely on that at some point in boot time, chronyd sets the time. If a file is updated prior to chronyd accomplishing its task (or network connectivity is down), the file ends up with a timestamp of "Dec 31 1969". I notice that occasionally, after a reboot, /etc/aliases.db reverts to this time,
2024 Feb 10
2
Joining Windows 10 Domain Member to Samba AD/DC
On Sat Feb 10 15:31:47 2024 Mark Foley <mfoley at novatec-inc.com> wrote: > > On Sat, Feb 10, 2024 at 2:20?PM Mark Foley via samba > <samba at lists.samba.org> wrote: > > Does chrony have to be built in some special way to enable ntp-signd? > > Needs to be configured with "--enable-ntp-signd". I may have to build from sources. I downloaded from the
2016 Dec 27
0
chronyd configuration as a local ntp server
'Modern' NTP allows for all sorts of updates to NTP servers, with all sorts of attacks. So to prevent even local hosts from making changes to your NTP server, there is the restrict instead of allow command. Its intent is to limit what the server will accept from a host in the address range instead of allowing any command from within that range. I use this on my Centos6 servers. I
2016 Dec 27
0
chronyd configuration as a local ntp server
On Mon, Dec 26, 2016 at 11:04:22PM -0500, Robert Moskowitz wrote: > This is for centos 7 that has chronyd 2.1.1 > > I am looking into how to use chronyd as my local ntp server. > > On my old servers with ntpd I had local access control lines like: > > restrict 192.168.128.0 mask 255.255.255.0 nomodify notrap > > > But in looking for documentation on chronyd I did
2020 Nov 03
3
ntp/chrony on AD DC and SELinux
Hi, the instructions for "Time Synchronisation - SELinux Labeling and Policy" on https://wiki.samba.org/index.php/Time_Synchronisation_-_SELinux_Labeling_and_Policy don't seem to work on CentOS 8. Using chrony I tried to adapt them (with very limited SELinux knowledge) like this: chcon -u system_u -t chronyd_exec_t /var/lib/samba/ntp_signd semanage fcontext -a -t chronyd_exec_t
2017 Feb 05
2
Chrony vd NTP
I have read: http://thegeekdiary.com/centos-rhel-7-chrony-vs-ntp-differences-between-ntpd-and-chronyd/ My server is up all the time and will serve time to internal systems (via DHCP options). Caveat is that my server is an armv7 (Cubieboard2) which does not have an RTC (no battery). So whenever the system boots, the time is ZERO (Dec 31, 1969 or some such). Chrony fixes this really fast;
2019 Apr 25
3
Windows clients require reboot once a day in order to access mapped drives
> > > Forgot to mention, are sure your time sync over AD is working correctly. > One to add to you list, check times of server and clients, (* yes again, > if needed just to be sure). > Yes, I have double check that time is correctly being synced. FYI, Rowland, the process outlined in the wiki for using chronyd does not work on Ubuntu 18.04 (my AD DC is on Ubuntu, but my file
2017 Apr 20
7
What besides Postfix should not start until system time set?
So I have learned that Postfix should delay until Chronyd has moved the system time from 0 to current. What other services need to be delayed? Apache? Bind? Of course if this is a nameserver, Chronyd will probably not be able to resolve the NTP server addresses until Bind is running! thanks
2017 Feb 05
2
Chrony vd NTP
On 05/02/17 16:15, Richard wrote: > >> Date: Sunday, February 05, 2017 10:26:05 -0500 >> From: Robert Moskowitz <rgm at htt-consult.com> >> >> I have read: >> http://thegeekdiary.com/centos-rhel-7-chrony-vs-ntp-differences-bet >> ween-ntpd-and-chronyd/ >> >> My server is up all the time and will serve time to internal >> systems (via
2015 May 24
3
Systemd
On 5/23/2015 11:22 PM, Luigi Rosa wrote: > Kirk Bocek wrote on 24/05/2015 04:37: >> So I've built my first CentOS 7 host and am learning all the new ways >> of doing >> things. I setup and enabled ntpd but after a reboot I get: > > In CentOS 7 is bettere to use chrony, here's an howto > > http://linoxide.com/linux-command/chrony-time-sync/ > So
2017 Feb 05
1
Chrony vd NTP
> Date: Sunday, February 05, 2017 10:26:05 -0500 > From: Robert Moskowitz <rgm at htt-consult.com> > > I have read: > http://thegeekdiary.com/centos-rhel-7-chrony-vs-ntp-differences-bet > ween-ntpd-and-chronyd/ > > My server is up all the time and will serve time to internal > systems (via DHCP options). > > Caveat is that my server is an armv7
2020 May 08
1
Chrony
I just happened to notice this morning in /var/log/messages: chronyd[1299]: Selected source 207.244.103.95 host 207.244.103.95 95.103.244.207.in-addr.arpa domain name pointer dns-e.wdc-us.hosts.301-moved.de. Just curious why my machine in Indiana (USA) is asking for time in Germany. Wouldn't it use something closer ? Thanks, jerry
2019 Nov 27
2
security = ads parameter not working in samba 4.9.5
On 27/11/2019 15:30, S?rgio Basto wrote: > On Wed, 2019-11-27 at 12:29 +0000, Rowland penny via samba wrote: >> On 27/11/2019 11:03, S?rgio Basto via samba wrote: >>> Sorry I meant man idmap_ad. But checking again man is equal of >>> https://wiki.samba.org/index.php/Idmap_config_ad in EXAMPLES of man >>> page [1] >>> >>> Examples don't