similar to: Samba4 on Ubuntu 18.04

> Date: Tue, 8 May 2018 06:52:56 -0700 > From: Gregory Sloop <gregs at sloop.net> > To: samba at lists.samba.org > Subject: Re: [Samba] Samba4 on Ubuntu 18.04 > > A sort of digest reply... > > RPvs> Not sure, what is a samba4/adc ??? > RPvs> Or do you mean a 'Has anybody joined a Samba DC on Ubuntu 18.04' ? > Yes, doing an active directory

Hai, I detected a minor error and i added a quick fix. And i'm testing my 4.8.1 debian package on ubuntu 18.04, see below.. Syslog shows. May 9 14:50:26 ubuntu1804 systemd[9448]: /lib/systemd/system-generators/netplan failed with exit status 1. The fix is: editor /etc/netplan/01-netcfg.yaml The last adresses: needs a server adres. cat /etc/netplan/01-netcfg.yaml # This file describes

Hai,   I've just tested the new samba 4.8.2 on my debian stretch and a ubuntu 18.04 test server (AD DC server) Rowland, can you test these on your Duvean server also?  :-)   You only need the following for samba 4.8.2 of my repo: echo "deb http://apt.van-belle.nl/debian stretch-samba48 main contrib non-free" | sudo tee -a /etc/apt/sources.list.d/van-belle.list wget -O -

Hai Paul. Yep. time sync is a must in ADDC setups and for very server it a must imo. You might need to sync a hardware clock also, because if the hardware clock gets more then 5 min out of sync. You might end up en some strang problem. And do note, NTP Server is only needed on the DC,s members, just point them to the DC. Better imo, add CNAME ntp1 to dc1 and ntp2 to dc2 and use the ntp1/2

Hi Parke, Thanks, no I had not run those commands, but after doing so, my VPN address is not visible. See below: nsasia at db2:/etc/tinc$ sudo systemctl enable tinc at VPN1 Created symlink /etc/systemd/system/tinc.service.wants/tinc at VPN1.service → /lib/ systemd/system/tinc at .service. nsasia at db2:/etc/tinc$ systemctl start tinc at VPN1 ==== AUTHENTICATING FOR

On Wed, 16 May 2018 09:38:55 +0000 Paul Littlefield via samba <samba at lists.samba.org> wrote: > Hi List, > > My 2p worth... about Ubuntu 18.04 Server with Samba 4 AD DC. > > TIMEZONE = I set up my server for the actual timezone, rather than > UTC... $ sudo dpkg-reconfigure tzdata > > NTP = I use the new systemd timesync daemon instead of good old > ntpd... $

We are having one server machine (ubuntu 16.04 OS) with 10 VMs. When the server is rebooted, some VMs got failed to boot with systemd/dbus error messages. Rebooting the affected VMs resolves this issue. Jan 30 20:40:02 VM systemd[1]: Failed to subscribe to NameOwnerChanged signal for 'org.freedesktop.DisplayManager': Connection timed out Jan 30 20:40:02 VM systemd[1]: Failed to subscribe

Aah.. Sorry typo. systemctl unmask samba-ad-dc (umask / unmask ) systemctl enable samba-ad-dc systemctl start samba-ad-dc Im very buzy, so slow in responce atm, but if a service fails to upgrade and starts it gets masked. Unmasking is needed then. To make sure its all enable i also run extra enable. > -----Oorspronkelijk bericht----- > Van: Stefan G. Weichinger [mailto:lists at

> -----Oorspronkelijk bericht----- > Van: samba [mailto:samba-bounces at lists.samba.org] Namens > Stefan G. Weichinger via samba > Verzonden: vrijdag 6 maart 2020 10:41 > Aan: samba at lists.samba.org > Onderwerp: Re: [Samba] DCs from 4.10.x to 4.11.x > > Am 06.03.20 um 10:11 schrieb L.P.H. van Belle via samba: > > After upgrade indexing is done as far i know.

I installed two samba ad in replication. One fileserver (domain member) and printserver (domain member). I built a CTDB cluster with it. All are running on Ubuntu 18.04 LTS! On the AD Server i got a problem with the internal DNS from samba because systemd-resolver thought it is the DNS boss now. I disabled systemd-resolve (systemctl disable systemd-resolved.service) and mange the

Hai, @Rowland. Yes yes, you did say you hate systemd. :-) I had a hard(er)time on this one also but i got passed it. ;-) But you and everybody else on the list, please review this setup. And a very big thank you Rowland for the start of it. This should be a good base to start with as howto for ubuntu 18.04 systemd based. Any suggestion additions please add them, below is also the order

Am 03.12.2013 17:36, schrieb Stefan G. Weichinger: > > On a gentoo server with libvirt-1.1.3 I get problems with starting VMs. Additional logs: # journalctl -f lists Dec 03 18:19:31 jupiter systemd-machined[23995]: Failed to start machine scope: Method "StartTransientUnit" with signature "ssa(sv)" on interface "org.freedeskt...sn't exist Dec 03 18:19:31

Running a Samba 4 AD DC on Ubuntu 18.04, and fileservers on 18.04. Our access control needs are rather simple and worked well under the samba 3 series with LDAP users and groups so we plan to keep using the POSIX ACL (regular filesystem access controls) On a fresh install file server(18.04) samba 4 with POSIX ACLs work with no issue, but I can't get the permissions to work properly on the

This worked for me until here: root at dtmbr0tst:~# mkdir sources root at dtmbr0tst:~# cd sources root at dtmbr0tst:~/sources# apt-get build-dep samba Reading package lists... Done E: You must put some 'source' URIs in your sources.list Suggestions? On Thu, Feb 1, 2018 at 7:04 AM, L.P.H. van Belle via samba < samba at lists.samba.org> wrote: > Hai, > > I've had a

I was rereading this i missing one thing, my dislectic got me again.. In the last part. Just before all systemctl's. This : and we change the systemd-resolved and point it to the IP ( NOT localhost ) of the server now change the systemd-resolvd DNS. sed "s/DNS=8.8.8.8/DNS=$(hostname -i)/g" /etc/systemd/resolved.conf The sed line should be : sed -i

Top posting... While I don't really see any details that indicate this is the problem, systemd-resolved causes the packaged 18.04 samba to fail to start [at least in a full AD setup.] That's because system has a full DNS resolver, and Samba also has it's own DNS resolver. When they both try to start on the same port, the first running wins [systemd] and Samba exits. Since you're

That link your using has few poing that needs fixing.. Its not a bad exampl.e For example. 5. apt-get install ntpdate.. Should be : apt-get install ntp You should configure the NTP daemon also on the AD-DC. Point (step 3) 10. systemctl stop samba-ad-dc smbd nmbd winbind Also needs systemctl stop disable smbd nmbd winbind systemctl stop mask smbd nmbd winbind 12. winbind enum users =

On my Centos 7 update, into "journalctl -f" I have tons of this kind of message > feb 17 23:52:09 s-ispc.local systemd-logind[663]: Got message type=signal sender=:1.0 destination=n/a object=/org/freedesktop/systemd1/unit/php_2dfpm_2eservice interface=org.freedesktop.DBus.Properties member=PropertiesChanged cookie=17152 reply_cookie=0 error=n/a > feb 17 23:52:09 s-ispc.local

Hai guys, After a few messages on the list on Buster, i decided to upgrade one of my production AD-DC's and see what happens. If noticed a few things here, so here are the steps and changes i made to upgrade and have a correct working AD-DC after the upgrade. Setup is as followed: Debian Stretch AD-DC with Bind9 DLZ and ntp time. This is still the base i used for my AD-DC

Hai, Sorry Harald, but this is really bad advice. If you want problem when upgrade, this is the way. Things like this get forgotten in time.. And really... . I learned this today. If i can so can you guys. Great info here: https://wiki.archlinux.org/index.php/systemd-networkd https://wiki.archlinux.org/index.php/Resolv.conf#Systemd-resolved_configuration .. Yes.. I do debian ( bit ubuntu