similar to: MSDOS "System" Attriubute for Folders

First of all, My apologies for this maybe slight OT post, but I have so much confidence and read so much good replies on this list, that I am still asking my question. I''m looking for a linux distribution to use on our school''s homemade routers. The routers are small miniITX based systems with 2 network interfaces. I added a 4 port D-Link network card in some cases, when I

Hi list, Does Samba support large extended attributes? By this I'm referring to attributes that are alternate streams attached to a file. http://msdn.microsoft.com/en-us/library/aa364404%28v=vs.85%29.aspx Seeing a problem when the referenced stream points to large files (sometimes 3M+). Thanks for the help, - T

Hi, there are two issues wich cost me some time to figure out and maybe it made sense if someone put them into the documentation and / or wiki, because without these addressed my system ran pretty instable and wasn''t very usable. This applies to xen-3.0 and kernel 2.6.12.6-xen: 1) Networking issue With the default bridged setup, networking was quite flaky, e.g. samba access from dom0

If 'msdos' filesystem is not compiled in Kernel (and I don't have the msdos.ko module neither), then syslinux refuses to work. Is it possible to fix syslinux to try more filesystems, not only msdos? Or is it possible to call the mount command somehow without filesystem option at all, so the kernel (or whatever) will decide itself what filesystem to use? Thank you for

Hi, How are you! I built a PXE server of MSDOS in Linux server, client can boot from network and login MSDOS, but by default, the output console is VGA, My target client has not VGA port, it can only output from serial port, so could you help to tell me how to boot a MSDOS client from network and keep the PXE client output console is serial port ? Below is the PXE configure file?s

Hello, I am looking for the first time at setting up Linux with Samba as a primary server on our network. I would like to replace my SCO Unix system and a Windows box I use to serve MSDOS machines. The MSDOS server seems to be the stumbling block at this point in my research. I can only run netbEUI on them as far as I know and Samba seems to only talk on TCP/IP. Do you know of a solution?

I have many hp laptops that boot msdos with memdisk + pxelinux perfectly. However, I recently have the need to usb boot msdos with syslinux. And memdisk. When the dos Image loads I get "loading bootsector..." and then it halts. Sometimes I can get "starting ms-dos" but freezes as well. I'm trying to boot clean msdos floppy image created with winimage. I'm using

Hi! Windows Applications seem to run fine uder wine, but for any MSDOS-Application FILE, I get the following error: wine: can't exec 'FILE': invalid exe file Protocol error: process 0x806a100: partial recvmsg 0 for fd This happens regardless of winver/dosver (wine is called by 'wine --winver winxyz --dosver x.yz FILE'). What am I doing wrong? Do I need to start some kind of

Hi, I have a PC that acts as a VoIP gateway using an internet telephony provider to make phone calls.. Data between me and the provider will always be from one IP address on my internal network to the provider.. I have a 1Mbps/256Kbps ADSL line and the voice stream is highly compressed requireing only 30Kbps of bandwidth.. The problem is that when my Mozilla Mail client polls for mail or

Running samba 1.9.16p11 on Digital Unix 3.2c. We currently access unix shares from W95 without problems but now since we had our network overhauled, 2 MSDOS harddriveless PC's need to be able to access the unix system for it's hard drive. They have Intel Express cards . How do I setup the MSDOS computer to map a drive to SAMBA. One question is these computers do not have IP addresses, how

I have the same problem. I can not boot a floppy disk. Once I did it but no longer I can do this. I think there is some problem in the new versions of PXELinux. -----Original Message----- From: syslinux-bounces at zytor.com [mailto:syslinux-bounces at zytor.com] On Behalf Of Quinn Plattel Sent: Thursday, September 28, 2006 7:04 PM To: syslinux at zytor.com Subject: Re: [syslinux] problem booting

Hi all, I try to boot an msdos system using pxelinux and memdisk on my PC engines Wrap-2.c card and I have problems with it This is what I see: PXELINUX 3.11 Debian-2006-03-16 Copyright (C) 1994-2005 H. Peter A boot: msdos Loading memdisk.... Loading images/msdos/msd622bd.dosim......................... Ready. dp83815: Setting full-duplex based on negotiated link capability. MEMDISK 3.11

This is my situation : FTP/Webserver ------| Mailserver ---------|-------Cisco 827 RTR-----Internet DB App. server -----| I want to do the following : FTP/Webserver ------| Mailserver ---------|------BRIDGE------Cisco 827 RTR-----Internet DB App. server -----| The internet connection is 3mbit/384kbit ADSL connection, with 1 fixed address. The cisco router is acting as a router with NAT. Some

Hello all, I am using MSDOS client together with Samba version 3.020 running on a freebsd server version 4.8. I can write fromout this client with 1 Mbyte/min as maximum speed using GHOST. The CPU load from the freebsd server is nearly zero. When using Windows as system i can copy with a speed of 150Mbyte /min to the same Samba server. What must i check or change to get approx. the same speed

I am having this same issue... Has anyone resolved this? Thanks...

I found that if I do not have a local floppy installed and enabled on my client, I will get the error 'Non-system disk' when I try to boot DOS floppy images. NT or Syslinux floppy images boot fine. If I enable the floppy in the BIOS, then it boots the DOS floppies just fine. Is this normal? Is there a workaround? There are MS-DOS images, so perhaps this is an MS-DOS limitation. --

I've been sitting in on this mailing list for a long while now, and I wanted to know, if there are any guide lines on getting a system to boot a DOS boot disk over the wire, ie, via PXE booting? I know this has been covered, and I am also googling for a site to help me out, but I thought I would ask anyway, so that I don't get lead astray. I have a thin client setup already up and

Is anyone actively working on the dos emulation, or should I just start hacking away? -- Chuck Crayne ----------------------------------------------------------- ccrayne@crayne.org -----------------------------------------------------------

I am working on creating a program for some simulations I need to do and I want to execute a Perl script that I wrote using the system() command in R. I have spent a couple days trying to figure this out and it appears that my problem occurs when sending the perl script file path through R to MSDOS. I have tried using double backslashes, quotations, etc. Moving my files to the root directory with

Hi All, Here's an interesting one... I need to be able to connect smbclient on a linux machine to a dos based machine, which is running MSCLIENT and the WG1049 patch. I can browse to the machine and see all the files from Network Neighbourhood in Windows, but if I try and go in with: smbclient \\GAUGE1\C, or even just smbclient -L GAUGE1 all I get is: Added interface ip=10.0.1.1