similar to: Routing in tinc 1.1

> homeClient<br> > Network Bridge: (local Area Network and TAP-Win32) 192.168.6.107 mask 255.255.255.0 gw 192.168.6.1<br> change -> mask 255.255.0.0 > Tinc.conf<br> > Name = homeClient<br> > ConnectTo = vpnoffice<br> > Mode=switch<br> Change -> Mode=router Why everybody wants switch??? Add -> TCPonly=yes > vpnoffice: Network

I use 3 Ubuntu server 14.04 as KVM guest. Now I run 5 tinc vpns in switch mode. I use the same key for every vpn. Every kvm has connect to the two other servers. I need 5 vpns to have 5 networks connected but seperated. 1 vpn was running fine, but now that I run 5 vpns, my kvm crashes sometimes. Especially when I stop tinc. I used tinc 1.0.26 from repo. Now I tried tinc 1.1 pre, same problem but

Hello, did anybody already compile tinc for fritzbox routers? They are very famous in Germany and i like to run tinc on my fritzbox. Otherways maybe anybody can help me how I can do this. But I'm no good programmer... ALBI...

Hi, is it possible to use tinc via https proxy? I mean tell tinc to connect via https proxy to my tinc server. I heared openvpn can do this. Can tinc do that the same way? ALBI...

Hi, is there a tinc version for android? I hope so! ALBI...

Hi, I have two tinc nodes which announce default gate to internet. How does tinc select which node is prefered when I route to the tinc device and not a special ip? tinc 1.0.16 ALBI...

Hi, how does tinc decide where to route a packet? I know default weight is 10. Does tinc add all weights and choose the lowest? Will 3 hops with weight 10 prefered before one hop wih weight 50 ? ALBI...

On Sat, Mar 26, 2016 at 12:03:48AM +0100, albi at life.de wrote: > 1 vpn was running fine, but now that I run 5 vpns, my kvm crashes sometimes. Especially when I stop tinc. > I used tinc 1.0.26 from repo. > Now I tried tinc 1.1 pre, same problem but less often. > > Any help or idea why system crashes? So the KVM instance itself crashes? Or Linux inside the VM? Any error messages

On 8.2.19. 22:39, albi wrote: >>> The setup looks like this: >>> web <- tinc "tiosp" -> gateway <- tinc "tiutl" -> backup > Which lan ips do all your computers have? network addess will be fine. > > > ALBI... Hi Albi, web:   tinc tiosp: 172.16.1.10   local: 10.0.0.5 gateway:   tinc tiutl: 172.16.0.5   tinc tiosp: 172.16.1.5   local:

Hello, did anybody already compile tinc for fritzbox routers? They are very famous in Germany and i like to run tinc on my fritzbox. Otherways maybe anybody can help me how I can do this. But I'm no good programmer... ALBI...

*hvjunk said:* > Get a RPi (or faster/cheaper/equivalent), and bridge it into the Mikrotik………. Unfortunately, I don't think this is an option (even if I may put there a full PC, not only a Raspberry Pi), for a few reasons: - what I'm trying to achieve is to substitute MikroTik's native L2TP/IPSec tunnels with tinc, not to have TWO tunnels - supposing I have two different tunnels

On Fri, Sep 25, 2015 at 08:41:06AM +0200, Marcus Schopen wrote: > I'm running some tinc clients behind a NAT (masquerading, Cisco Router) > connecting to a host outside on a public IP in a different network. The > tunnels get unstable every few minutes and I see packet loss when > pinging the clients on their internal tunnel IPs from the host side. > Before putting the tinc

Any news about tinc for Android? ALBI...

Hello, does anybody know which version of tinc I can run on my Acer 110l with original Linous Linux? As i know it is build on Fedore 8, but I never used Fedora before and I don't want to destroy my 110l :-) ALBI...

Hello, I think routing could be improved in several ways, at least, there lacks some documentation describing how Tinc routes packets. In order to test Tinc, I setup the following virtual network: - tinc 1.1pre9 with ExperimentalProtocol=yes - use of network namespaces (actually python-nemu[1]) - star topology, where all nodes runs tinc except the center, which I use to filter communications,

If you're using a TUN interface, then your question does not make sense because a TUN device operates directly at layer 3 (IP) - there is no MAC address to set in the first place. If you're using a TAP interface (i.e. layer 2, Ethernet) combined with router mode (an unusual setup, at least on Linux), then you should be able to change the MAC address of the virtual device, but the exact

If your question is "can I assign the same subnet to multiple tinc nodes on the same network", the answer is yes (for both 1.0 and 1.1). That can indeed be used for seamless failover. That said, when sending packets to a subnet assigned to multiple nodes, it is not very well-defined which node tinc will send the packets to - currently it tries to estimate which one is closest by

Hello everybody, I am doing some test with TINC and Windows 7 and I am having some issues with routing. (see attachment for the client configuration) The set-up I configured uses DHCP over the TINC tunnel and the Windows guests ends up with two gateways (one from its own network and one from the TINC network). The problem is that traffic when browsing the internet should go over the TINC tunnel

Hi, Hopefully someone can help me. I've been trying to set up a private vpn, for both internal ipv6 and ipv4 traffic. There are two Hosts involved with the vpn at the moment. I've been struggling with this but am now going round in circles - Can anyone recognise and explain what i'm doing wrong? The tinc daemons are listening on an ipv4 address, connected to the standard

Hi! I have compiled and installed tinc 1.1pre5 on a ubuntu machine. With the tinc 1.0.x version that is included in the ubuntu repository I am used to having the config files in /etc/tinc/ and where each vpn has a own directory. The file nets.boot placed in /etc/tinc where I can specify which vpn tunnels that is going to start automatically. How can I get the vpn tunnels to start automatically