similar to: Config include

Hi, I have two tinc nodes which announce default gate to internet. How does tinc select which node is prefered when I route to the tinc device and not a special ip? tinc 1.0.16 ALBI...

We run tinc in router mode on over 10 server. Some server announce the same subnet. I can add routing with subnet-up and remove routing with subnet-down. But if I do this, my routing will be removed when only one anncounce comes in, even there is an other server who still has the routing to the same network. Is it possible to run subnet-down only it the last announce to a subnet is going down?

I use 3 Ubuntu server 14.04 as KVM guest. Now I run 5 tinc vpns in switch mode. I use the same key for every vpn. Every kvm has connect to the two other servers. I need 5 vpns to have 5 networks connected but seperated. 1 vpn was running fine, but now that I run 5 vpns, my kvm crashes sometimes. Especially when I stop tinc. I used tinc 1.0.26 from repo. Now I tried tinc 1.1 pre, same problem but

Hello, I just tried tinc for win the first time. I use tinc on linux computer for some time already. Now I get the following error: Dec 18 14:57:39 narnia tinc.life[10884]: Connection from 217.187.51.119 port 35059 Dec 18 14:57:39 narnia tinc.life[10884]: Connection with mwflapar1 (217.187.51.119 port 35059) activated Dec 18 14:57:44 narnia tinc.life[10884]: Received UDP packet from unknown

Hi, Guus The use case the shared default gateway for multi-tenant, if that the case the node who own the default gateway will have problem to route with different tenant who has overlapped address scope? Is it true when no any other tools like the namespaces? (tenant1)\ (tenant2)——common node—— shared gw node—— Internet (tenant3)/ But if the each tenant have it’s dedicate default gateway, but

Hi, how does tinc decide where to route a packet? I know default weight is 10. Does tinc add all weights and choose the lowest? Will 3 hops with weight 10 prefered before one hop wih weight 50 ? ALBI...

Hello all, Thank you for tinc, that is an **excellent** and useful package! Taking into account that both Red Hat and Debian (8.x) families now use systemd, there is, IMHO, one small. but important correction to be done: tinc's initialization. IMHO, we need: 1. A proper tinc.service file, included by default (prepackaged) in the stock .deb and .rpm packages in Fedora, Debian, Ubuntu,

On Mon, Dec 08, 2014 at 11:02:24PM -0500, md at rpzdesign.com wrote: > The self contained example is tricky because I created 4 ip-address on > the eth0 device (192.168.1.30/31/32/33) so I could test a 4 node VPN > that lives entirely within a single server. That's quite hard to do, it's far easier to run four instances of tinc on four different ports on the same machine. >

Hi Team, I admit that I am not familiar with Tinc very well, but have Tinc running at approximately 20 sites and functioning as a mesh vpn/network. I am having issues adding an additional site as it will not communicate with the rest. I have taken the firmware of one and flashed it on another router to make it duplicate and then tested it working but when I change the hostname, and IP to what we

Hi, is it possible to use tinc via https proxy? I mean tell tinc to connect via https proxy to my tinc server. I heared openvpn can do this. Can tinc do that the same way? ALBI...

On Tue, Mar 01, 2016 at 04:31:13AM -0600, md at rpzdesign.com wrote: > Where do I get information about the details of not needing a tinc-up script > anymore? (/etc/network/interfaces) You can just use the normal /etc/network/interfaces way of configuring the interface, like this: iface vpn inet manual address 192.168.1.1 netmask 255.255.255.0 tinc-net <netname> > Also,

Hi, Tinc expert For use case of multi-tenancy use case, should I use multiple netnames (/etc/tinc/tenant1, /etc/tinc/tenant2/, etc.) for the network, so that even different tenant have overlapped network address will be possible to work in the same physical host? or can not?

It would be nice if in a next tinc release you'll add some service variables tinc propagates to its scripts. So for example you can define in tinc.conf env variables like: SERVICE1= ... SERVICEn= and tinc will propagates all SERVICEx Variables found in tinc.conf to all scripts it calls. One can use theoretically infinite Env Var for custom behavior (like custom debug messages, conditional

hey there, Tinc will generate a new MAC address every time the daemon restarts. In my setup, in switch mode, I give IP addresses using DHCP to the different tinc vpn clients. Some of these boxes are 'pets' and request a particular ip address which is specified in their dhclient.conf. My trouble is that since the MAC is regenerated every time the daemon is restarted, I am forced to have

Is there any way to obtain the public key from the private key? I know it's in host file however for the purpose of this message I need to be able to generate it on the command line. I tried openssl ec < ed25519_key.priv I get an error read EC key unable to load Key 140092556813984:error:0906D06C:PEM routines:PEM_read_bio:no start line:pem_lib.c:703:Expecting: ANY PRIVATE KEY

First off, thanks to all who have made tinc possible and continue to work developing it. I hope perhaps in time I can become a useful part of this community. :) I'm having an interesting issue with tincctl and was hoping someone could shed some light on it. Everything seems to work correctly when I build for OSX; however on linux and windows builds, I always receive connection

Hi all, I am trying to setup a configuration of Tinc to allow multiple tincd daemons for a same network (mixing bonding, etc...). I will post my solution later if I found one. This is to get better speeds in multiple gigabit/sec networks. So my question is not about this directly. I would like to know if the "netname" configured on each node, is used somewhere in communications

I have a tinc mesh consisting of 6 Windows servers. All are configured identically and all but one work without any problems. On that one server however the tinc service starts, but the connection does not come up (no packets get routed, ping times out). If I stop and start the service manually, the connection is up in like half a second. If I start tinc on the command line, it works every time.

Hi We have several stale nodes in our tinc network and I'd like to remove these. These nodes show up in graph dumps as red nodes, indicating they are unreachable. We run: tinc -n <vpn-name> purge Nothing happens. If we tail the logs at /var/log/syslog, we dont see an ack or message concerning the purge either. The dead nodes still show up in the graphs and their certs are still

Hi! When I try to use tinc I get this message 'Cannot route packet: unknown type 0' when I try to ping or ssh to the box I'm connected to. Below is my setup: ifconfig tun device: -------------------- midkemia Link encap:Ethernet HWaddr FE:FD:00:00:00:00 inet addr:192.168.6.1 Bcast:192.168.6.255 Mask:255.255.0.0 UP BROADCAST RUNNING NOARP MULTICAST MTU:1500