similar to: Centos 7: setting DSCP values on bonding interfaces?

Hi, Can anybody tell me how to delete DSCP or TOS setting using iptable command. iptables --list OUTPUT --table mangle Chain OUTPUT (policy ACCEPT) target prot opt source destination DSCP tcp -- anywhere anywhere tcp spt:http DSCP s et 0x08 DSCP udp --

CentOS 6.2......... Why do the physical interfaces report (correctly) that they're negotiated at 1000Mb/s, but when I `cat /proc/net/bonding/bond0` I get 100Mbps for the member interfaces, and when I ` mii-tool bond0` I get 10Mbps for the bond? ----------------------------------------------------------------------------------------- ethtool em1 Settings for em1: Supported ports: [

Hi, examining the network traffic with wireshark shows that asterisk does not set any QoS values at all. What do I need to do to make asterisk set QoS values (on Centos 7)? The wiki says to use vconfig to set QoS values[1]. What does the skb-priority need to be set to? How do you use vconfig on interfaces that are not VLAN interfaces? Is it generally impossible to set QoS values on

Hello list, I need to set Voice QoS and SIP QoS for YeaLink. The possible values are 0 ~ 63. With Grandstream I can fill in DiffServ 46, which is EF. That's what I want. With Snom I fill in 184, which corresponds to EF or DSCP 46 (according to their wiki) But what value do I want to fill in with this YeaLink ??? This is a conversion table :

Hi all, i recently found that some frontend servers (Centos6) show: kernel: bonding: bond0: link status definitely up for interface eth2. kernel: bonding: bond0: link status definitely down for interface eth2, disabling it kernel: bonding: bond0: link status definitely up for interface eth2. On some days frequently and on others none. But there is no hw failure or similar. $ cat

Did anyone ever answer this one? THIS is what I am trying to do: >[LARTC] cbq+sfq and DSCP marking >Maria Joana Urbano stmaria@dei.uc.pt >Thu, 13 Feb 2003 19:29:42 +0000 > > * Previous message: [LARTC] Monitoring.... > * Next message: [LARTC] two routes 1 network card > * Messages sorted by: [ date ] [ thread ] [ subject ] [ author ] >

I four nodes setup to do active-backup bonding and the drivers loaded for the bonded network interfaces vary between tg3 and e100. All interfaces with the e100 driver loaded report errors much like what you see here: bonding: bond0: link status definitely down for interface eth2, disabling it e100: eth2: e100_watchdog: link up, 100Mbps, full-duplex bonding: bond0: link status definitely up for

I am assuming that the TOS values directly map to DSCP values in the ip header. Is this a correct assumption? If so, can someone tell me the correct setting to set call control packets with a DSCP of AF31(011010) and media with EF(101110)? So would the setting for AF be TOS=46?? Is it possible to mark the media and call control separately?? -------------- next part -------------- An HTML

Hi, I want to setup core routers to do both DSCP marking and to get the DSCP and forward packets based on DS field. I don''t want to separate DSCP marking to be done only at the edge routers. I know that dsmark is both used for DSCP marking and for getting the DSCP and forwarding packets according to DSCPs. In my case, since I want to do both of these I need two dsmarks.(?) I am not

Hello I have two linux machines connected via 2 dsl lines (bonded) 192.168.0.1-eth0-dsl---2Mbit---dsl-eth0-192.168.0.2 ^-eth1-dsl---2Mbit---dsl-eth1-^ so the final figure is something like this: 192.168.0.1-bond0---4Mbit---bond0-192.168.0.2 I can only use arp monitoring for fail checking - if one dsl line fails - automatically use only the other one. I set up everything correctly (i

Hi, I have 2 servers running CentOS 6.3. Each has four 1gb Ethernet ports. I have bonded all four ports on each server and patched them to the same switch (following the instructions at http://wiki.centos.org/TipsAndTricks/BondingInterfaces). I have created aggregated trunks for the servers respective ports on the switch. The switch reports that the ports are up and that the Link Aggregation is

https://bugzilla.mindrot.org/show_bug.cgi?id=1964 Bug #: 1964 Summary: QoS/DSCP names false translated to ToS hex value Classification: Unclassified Product: Portable OpenSSH Version: 5.9p1 Platform: amd64 OS/Version: Linux Status: NEW Severity: normal Priority: P2 Component: ssh

Hello - Was wondering if anyone is running the bonding network driver in active/backup mode using arp_validate? I'm trying to deal with really crappy network switches from Dell and I thought I could work around their faults in the short term by switching from link monitoring to arp monitoring. But I ran into a situation just now that seems even arp monitoring isn't enough. This is my

Hello everybody, I have tried several iptables versions (from 1.2.4 to 1.2.6a) to mark outgoing packets (change the DSCP field) with no success. #iptables -A OUTPUT -t mangle -d 10.0.0.3 -j DSCP --set-dscp 0x2 iptables v1.2.6a: unknown arg ''--set-dscp'' TOS target is working fine, but I want to create different codes for EF and AF classes in a diffserv

Hi everyone After configuring bonding eth0 and eth1 in domU, "cat /proc/net/bonding/bond0" showed it was configured correctly. ----------------------------------------------------------------------------------------- Bonding Mode: fault-tolerance (active-backup) Primary Slave: eth1 Currently Active Slave: eth1 MII Status: up MII Polling Interval (ms): 0 Up Delay (ms): 0 Down Delay (ms):

Hi, DSCP match in /tcrules/ doesn''t work with CS6 and CS7, it provides an error "invalid value" for string and hexa values. It seems that it comes from /Chain.pm/, in the function /do_dscp/: fatal_error( "Invalid DSCP ($dscp)" ) unless defined $value && $value < 0x2f && ! ( $value & 1 ); I dont understand why "$value < 0x2f", but

I want to set the DSCP at the ingress of the router. I tried the following: iptables -A OUTPUT -t mangle -d 10.10.10.12 -j MARK --set-mark 1 tc qdisc add dev eth0 handle ffff:0 ingress dsmark indices 64 set_tc_index tc class change dev eth0 classid ffff:1 dsmark mask 0x3 value 0xb8 tc filter add dev eth0 parent ffff:1 protocol ip prio 1 handle 1 fw classid ffff:1 But the DSCP

Has anyone figured this out yet? Lots of places say to add the following to sip.conf of an Asterisk 1.2 system (current production machine/Asterisk as root): tos=0xB8 (Hex B8 = Decimal 184 = Binary 10111000) or if you are running Asterisk v1.4 or newer: tos_sip=cs3 ; Sets TOS for SIP packets. tos_audio=ef ; Sets TOS for RTP audio packets. tos_video=af41 ;

Hi, may be there are some best practice suggestions for the "best mode" for channel bonding interface? Or in other words, when should/would I use which mode? E.g. I do have some fileservers connected to the users lan and to some ISCSI Storages. Or some Webservers only connected to the LAN. The switches are all new cisco models. I've read sone docs (1), (2) and (3) so the theory

Can anyone comment on the DSCP quality of service settings on your Asterisk server? The network we're setting up has data on the default VLAN, Asterisk server and phones on VLAN 4, and we're using Polycom phones with a PC hooked up to the phone's pass-thru port. What iptables settings are you using on the Asterisk server for DSCP? What are your Polycom DSCP settings? We're using