similar to: mdadm issue

Gordon Messmer wrote: > On 7/23/19 11:12 AM, mark wrote: > >> Now, cryptsetup gives me the same UUID as I have in /etc/mdadm.conf. >> The >> entry in /etc/crypttab looks identical to the RAIDs for root and swap, >> but nope. > > > Can you post those files somewhere?? I'm confused by the idea that > cryptsetup is involved in or using the same UUID as an

Greetings, DIAX seems to work well placing calls, but I can't actually receive a call . Here, DIAX (x305) "registers", then I use a sip phone to place a call to DIAX (which definitely is not in use by me at debug time, but it is idle on my desktop.I think), and then * goes to vmail. Here's the debug output: affinity*CLI> iax debug IAX Debugging Enabled Rx-Frame Retry[N/A]

I've found a problem, and I think it is in syslinux (specifically when it tries to load ldlinux.e64 under hyper-V). I have a physical computer with a Gigabyte GA-P85-D3 motherboard that successfully pxeboots using the EFI images, and I hold that up as exhibit 1 that my deployment environment works. It also implies that the syslinux.efi image works in some cases, but not in all. My Hyper-V

I have inherited a system set up with multipath, which is not something I have seen before so I could use some advice The system is a Dell R420 with 2 LSI SAS2008 HBAs, 4 internal disks, and a MD3200 storage array attached via SAS cables. Oh and CentOS 6 lsblk shows the following: NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT sdd 8:48 0 931.5G 0 disk ??sdd1

OK, sorry, uncomment a line :-D Yes exist! ls -ld /opt/samba/var/locks/sysvol drwxrwx---+ 3 root BUILTIN\administrators 4096 Jun 16 11:25 /opt/samba/var/locks/sysvol ----- ls -l /opt/samba/var/locks/sysvol total 8 drwxrwx---+ 4 root BUILTIN\administrators 4096 Jun 14 2016 interno.MYDOMAIN.COM.BR ----- ls -l /opt/samba/var/locks/sysvol/interno.MYDOMAIN.COM.BR/ total 16 drwxrwx---+ 28 root

Hi guys, Last week I've switched from my old & good 3.4.63 to 3.14-rc1 and noticed nasty display corruptions when using nouveau. It seems that changing parts of the screen are appearing for a fraction of second in random places. I've recorded this behavior: http://www.youtube.com/watch?v=IEq7JzGVzj0 My hardware is some old motherboard with 00:05.0 VGA compatible controller [0300]:

Hello All, I have 8 servers.? 7 of the 8 say that gbe02 is in state State: Peer Rejected (Connected). gbe08 says it is connected to the other?7? but they are all State: Peer Rejected (Connected) So it would appear that gbe02 is out of sync with the group. I triggered a manual self heal by doing a the recommended ./find on a gluster mount. I'm stuck... I cannot find ANY docs on this

Hi - I am getting different results when I run the numerical integrator function lsoda (odesolve package) on a Mac and a PC. I am trying to simulating a system of 10 ODE's with two exogenous pulsed inputs to the system, and have had reasonably good success with many model parameter sets. Under some parameter sets, however, the simulations fail on the Mac (see error message below). The

Hi all, This is the third fresh install of CentOS 7 1708 the last two months that won't boot after a regular "yum update" just after the fresh install has finished. I've never had this problem before, it has just worked. The installs are on OEM's that have previously run CentOS 6.9 x64. Am I missing something here? -- BW, Sorin

Hello! samba -b | grep STATEDIR STATEDIR: /opt/samba/var/locks I commented at line idmap_ldb:use rfc2307 = yes in my smb.conf, error is diferent now samba-tool ntacl sysvolreset open: error=2 (No such file or directory) ERROR(runtime): uncaught exception - (-1073741823, 'Undetermined error') File "/opt/samba/lib/python2.7/site-packages/samba/netcmd/__init__.py",

I started rebalancing my volume after updating from 3.2.7 to 3.3.1. After a few hours, I noticed a large number of failures in the rebalance status: > Node Rebalanced-files size scanned failures > status > --------- ----------- ----------- ----------- ----------- > ------------ > localhost 0 0Bytes 4288805

On 6/17/2016 12:32 PM, Carlos A. P. Cunha wrote: > Hello! > Yes path is correct, so that when you run the reset Sysol he saw > changing permissions of various files (as mentioned) after a time > (over 10 minutes) the error occurred. > > dc 1 and dc 2: > > /usr/local/samba/etc/smb.conf > > [sysvol] > path = /opt/samba/var/locks/sysvol > > >

HI, i just played around with Windows 2008 R2 as ADS Server and two SAMBA 4 as additional DCs. Setting up the Samba 4 DCs works fine. Now I wanted to remove the last Windows DC with dcpromo. It fails with the following statement: Der Vorgang konnte nicht durchgef?hrt werden. Fehler: Active Directory konnte keinen anderen Dom?nencontroller f?r die ?bertragung der verbleibenden Daten

Has anybody sucessfully used puppetlabs-mysql (or some other method) to install MySQL-server on Linux with a my.cnf where datadir != /var/lib/mysql ? -- You received this message because you are subscribed to the Google Groups "Puppet Users" group. To unsubscribe from this group and stop receiving emails from it, send an email to puppet-users+unsubscribe@googlegroups.com. To view

Hi Karthik, thanks for taking a look at this. I'm not working with gluster long enough to make heads or tails out of the logs. The logs are attached to this mail and here is the other information: # gluster volume info home Volume Name: home Type: Replicate Volume ID: fe6218ae-f46b-42b3-a467-5fc6a36ad48a Status: Started Snapshot Count: 1 Number of Bricks: 1 x 3 = 3 Transport-type: tcp

Hey Richard, Could you share the following informations please? 1. gluster volume info <volname> 2. getfattr output of that file from all the bricks getfattr -d -e hex -m . <brickpath/filepath> 3. glustershd & glfsheal logs Regards, Karthik On Thu, Oct 26, 2017 at 10:21 AM, Amar Tumballi <atumball at redhat.com> wrote: > On a side note, try recently released health

On a side note, try recently released health report tool, and see if it does diagnose any issues in setup. Currently you may have to run it in all the three machines. On 26-Oct-2017 6:50 AM, "Amar Tumballi" <atumball at redhat.com> wrote: > Thanks for this report. This week many of the developers are at Gluster > Summit in Prague, will be checking this and respond next