similar to: C7 install, "failed to IDENTIFY"

I am trying to get a pv_ops dom0 working for testing, but I am running into an elf_init error: (XEN) *** LOADING DOMAIN 0 *** (XEN) elf_init: not an ELF binary Full output attached. >From what I have read on the mailing lists, it seems that it is usually a problem with either grub or a corrupt dom0 kernel. Attached is my kernel config (2.6.28-rc6-tip). I followed the instructions on:

OK, it seems that the kernel I have (stock CentOS 4.7: 2.6.9-78.0.22.EL i686) seems to gronk the nVideo SATA controller in AHCI mode. It is NOT able to deal with the SATA DVD Burner I have. It is a "Sony Optiarc DVD Burner with LightScribe Black SATA Model AD-7241S-0B LightScribe Support". Is there some special magic I need to do? Here is the relevant bit from the boot up (SATA ports

Got a bunch of servers from Penguin. Supermicro m/b's H8QG6. We put a 3tb drive in for additional workspace for the users, and some of them won't read, others will go for weeks, then spit out DRDY errors. lshw shows the controller as an ATI SB7x0/SB8x0/SB9x0 SATA. I did notice that it shows *-storage description: SATA controller product: SB7x0/SB8x0/SB9x0 SATA

Hello, I have experienced a dom0 crash where the system became unreachable via the network and the console was unresponsive. I would appreciate help interpretting the logs and any configuration change suggestions. It is a stock Debian Lenny dom0 running xen 3.2.1 with kernel 2.6.26-2-xen-amd64 and an AMD Athlon IIx4 with 4 GB of RAM. It is running 4 VMs. One VM has two PCI NICs being

Hey folks, So what's the word on AHCI and bios drive geometry? I'm having a real pain of a time trying to get some 750gb sata drives running on my FreeBSD7 box in AHCI mode. It doesn't seem to matter what disk geometry I suggest to sysinstall, something complains of an invalid disk upon booting it. Actually, in AHCI mode the bios screen doesn't report any information on

Hello there, I've got a question about SATA. I've got ASUS P5GC-MX/1333 with ICH7. (SATA2 support) A few HDD with SATA2. system: uname -a FreeBSD diablo.miekoff.local 9.1-STABLE FreeBSD 9.1-STABLE #1 r246666: Tue Feb 12 00:19:07 MSK 2013 root at diablo.miekoff.local:/usr/obj/usr/src/sys/DIABLO64 amd64 camcontrol info camcontrol iden ada2 pass2: <ST3500320AS SD1A> ATA-8 SATA 2.x

I sent a note about this a couple of weeks ago, but have not heard anything. I'm really getting a bit desperate. I have a system that I am trying to upgrade from 8.2 to 9.0. I have built it and installed the kernel, but it fails to boot. The boot freezes after probing for my hard drives during the probe of the CDROM. It just sits there, seemingly forever, though I have never waited longer

I am sure this is really simple. I have a setup of 2 disks (sda, sdb) which are outwardly identical, and are mirrors of each other. Together they form 3 raid1 devices. Both disks can boot. Now sda has bad sectors, and I should replace it. But which one of the physical disks is sda?? The machine boots fine from either one of the disks, (and the booting disk of course is always called sda).

On Tue, Oct 14, 2008 at 09:52:09PM -0400, John R. Huston wrote: > Hi, I am not very familiar with using mailing lists so if I have made > a mistake in the format or scope of the message please correct me. I > am pretty desperate for an answer by now so any help at all is really > very appreciated. > > I have a Shuttle SD30G2 computer (Specs: >

>> Doesn't work. Apparently the Dell UEFI PXE firmware doesn't know HTTP. > > There's a lot of variation. Do you have a shell option > in your boot selections? None of Dell OptiPlex 990 (firmware A19), 9010 (firmware A22), nor 9020 (firmware A16) seem have a built-in EFI shell option, but in all three cases I had success running the external EFI shell from

Hi all, I have had this problem since day 1 on my new server. It has run since November 15th 2008, and serve approx. 10 GB worth of web traffic per month for the main site and then some 40 domains with mail and small web pages. (hence - it's NOT that busy yet) I started with 7.1-RELEASE-pX since I didn't have problems straight off - but it didn't last long. After a few days of

Hi all, I installed CentOS 5 on DELL machine. Then, When the system comes up, I always get below erros. Could you pls help me to solve this out before I setup this box for productiuon use ? these are errors. usb 1-2: device not accepting address 2, error -71 ata2: port failed to respond (30 secs) ata2: SRST failed (status 0xFF) ata2: SRST failed (err_mask=0x100) ata2: SRST failed (status

Hi folks. I'm posting this to both the Fedora as well as the CentOS lists in hopes that somewhere, someone can help me figure out what's going on. I have a dual Xeon 3GHz server that's performing rather slow when it comes to disk activities. The machine is configured with a single 160 GiB OS drive (with CentOS 5.0) and 4x500 GiB drives setup in a RAID-5 configuration.

Hi, I have a Asterisk with two Cisco ATA connected with each other . Cisco ATA1 is connected via satellite link Cisco ATA2 is connected via leased line The problem is CISCO ATA2 can call CISCO ATA2 with no problem But CISCO ATA1 cannot call CISCO ATA2 . Any suggestion please Rabii -------------- next part -------------- An HTML attachment was

I've tested both 6.3 and 7.0-RC2, amd64 architecture, and have found the occurrence of an interrupt storm using an ASUS A8N-SLI Premium (nForce 4) motherboard with an AMD Opteron 175. Relevant dmesg output: atapci0: <nVidia nForce CK804 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 6.0 on pci0 ata0: <ATA channel 0> on atapci0 ata1: <ATA

Hi, I did a git pull on pv_ops tree this morning and now get a crash when eth0 is started, here is the full boot log: Booting ''Xen 3.4 / Linux 2.6.29-rc6-tip'' root (hd0,0) Filesystem type is ext2fs, partition type 0x83 kernel /xen.gz com1=115200,8n1 console=com1,vga iommu=1 [Multiboot-elf, <0x100000:0x131748:0x8e8b8>, shtab=0x2c0078, entry=0x100000] module

Since the update from kernel-2.6.32-754.2.1.el6.x86_64 to kernel-2.6.32-754.3.5.el6.x86_64 I can not boot my KVM guests anymore!? The workstation panics immediately! I would not have expected this behavior now (last phase of OS). It was very robust until now (Optiplex Workstation). I see some KVM related lines in the changelog.diff. Before swimming upstream: Does some one have problems

Hello all. I just updated my machine from 9-STABLE to 10-Stable today. beasty ~ # uname -a FreeBSD beasty.schavemaker2.local 10.0-BETA3 FreeBSD 10.0-BETA3 #0 r258543: Mon Nov 25 13:23:31 CET 2013 root at beasty.schavemaker2.local:/usr/obj/usr/src/sys/KRNL amd64 After a reboot, the console gets cluttered with a lot of messages. ata2: FAILURE - zero length DMA transfer attempted ata2: setting

Hello All, slightly unrelated because lightdm = epel, I know. Still, maybe someone had the same issue. When using the last two kernels, some machines give me trouble when installing Centos7 and Mate One machine is basically an Asrock board, on this I get no login screen: description: Motherboard product: AD2550B-ITX vendor: ASRock *-display description: VGA compatible

Yes on optiplex 790 i upgraded from A07 to A18 (there was a nic upgrade) but it didn't change anything.. On optiplex 380 i upgraded from bios A01 to A07(don't know if upgrade contained pxe or not)... I tried, lpxelinux.0 and it wasn't faster. Only v4.07 helped on these machines. Tomorrow, i will give a try with 6.03pre2. In wireshark, i saw no errors, the packet length was the