similar to: Need help with Linux networking interfaces and NIC bonding

Hello All, I seem to have run into a bug with the new --bridgeslaves=<INTERFACE> option. It would seem that if I tell the bridge device to use a virtual interface (like bond0) rather than a physical interface (em1/em2) that kickstart completely barfs on it. I have provided my network section below which works fine as long as i don't enable all the bridge content. When the

Hi all, Someone played with kickstart bonding with centos 6.4 ? CentOS 6.4, as upstream now support ifcae bonding in kickstart network section. I've an issue with configuring a second bonding iface in kicstart on CentOS 6.4. The first bonding (bond0) works as espected but the second is not configured during installation. I've a 6 nic server (two for "puclic" network, two for

CentOS 6.2......... Why do the physical interfaces report (correctly) that they're negotiated at 1000Mb/s, but when I `cat /proc/net/bonding/bond0` I get 100Mbps for the member interfaces, and when I ` mii-tool bond0` I get 10Mbps for the bond? ----------------------------------------------------------------------------------------- ethtool em1 Settings for em1: Supported ports: [

Hi, We have a Dell server with 4 Ethernet interface. I would to aggregate them in a bond. Everything work but the default gateway doesn?t work on the ? bond0 ? interface and I have no links. My configuration: - CentOS 7: :/etc/sysconfig/network-scripts# uname -a Linux nas-mtd2 3.10.0-957.5.1.el7.x86_64 #1 SMP Fri Feb 1 14:54:57 UTC 2019 x86_64 x86_64 x86_64 GNU/Linux - NetworkManager disabled:

Hello, I?m trying to configure a CentOS 7 server to act as a host for a bunch of virtual servers (KVM). I have an 802.3ad bonded Ethernet connected to the server with a bunch of tagged VLANs. I want to be able to build a bridge interface on the server for each VLAN and then attach that to the bond interface and the virtual clients. I also want to attach a host interface to one of the VLANs

Hi all, Read many posts on the subject. Using 802.3ad. Few problems; Cannot ping some hosts on the network, they are all up. Cannot resolve via DNS which is one of the hosts that I cannot ping, internal nor external DNS hosts. Unplugging the NICS and plugging them back in will then not allow pining if the default d=gateway. When cold booting it somewhat works, some hosts are pingable while

Hi All, I see an unexpected beahviour from NetworkManager on CentOS 7.1. Using nmcli tool, I create a bond with two slaves as explained in the Red Hat 7.1 Networking guide. I enable slaves and master; bond works as expected. When I restart NetworkManager, it creates a new bond with the same name but not connected to any device. Two bonds with the same name is confusing for my other monitoring

On 07/07/16 05:36 PM, Digimer wrote: > On 07/07/16 05:21 PM, Joe Smithian wrote: >> Hi All, >> >> I see an unexpected beahviour from NetworkManager on CentOS 7.1. >> Using nmcli tool, I create a bond with two slaves as explained in the Red >> Hat 7.1 Networking guide. I enable slaves and master; bond works as >> expected. >> When I restart

Hi, I've using linux bonding in active-backup mode to combine two pairs of GigE NICs (eth0/eth1, eth2/eth3) into two logical bonds (bond0/bond1). All is working fine. However, I would like to specify a primary interface for each bond. This means I need to specify different options to the bonding module for each bond. I have tried every conceivable incantation of options and cannot get the

Hi, I am facing a problem when I run tc on the bonded nic cards. When I run tc on a single nic card, it worked perfectly fine. But when I run tc on a bond of two nics, tc gives poor performance. The two nics were bonded in round-robin (load balancing) mode. I created a qdisc, class and a filter as follows: tc qdisc add dev bond0 root handle 1: htb tc class add dev bond0 parent 1: classid

Am 28.03.16 um 12:12 schrieb Leon Fauster: > Am 28.03.2016 um 11:27 schrieb G?tz Reinicke <goetz.reinicke at filmakademie.de>: >> We have three supermicron servers with two 10Gb Ports each, connected to a cisco switch stack 1Gb ports. All are on auto speed. >> >> I configured a LACP bond on both sides on all servers, first with citrix xen server. >> >> On

Guys, good afternoon I'm using in my bond interfaces as active backup, in theory, should assume an interface (or work) only when another interface is down. But I'm just lost packets on the interface that is not being used and is generating packet loss on bond. What can that be? Follow my settings bond [root at xxxxx ~]# ifconfig bond0 ; ifconfig eth0 ; ifconfig eth1 bond0

took a couple months off due to road blocks, hoping a fresh look would allow me to use my server as desired. I have three ports, eth0-2 over two nics. I want to bond them, and then use a bridge to connect to virtual machines on the virtual host computer. Never having done this, I am confused on some parts. Here is where I am at now and any pointers helpful. Single server, centos 6.x My issue

Hi! I just upgraded a machine to 7.7.1908 and the default route is not being set on boot. This particular server has a bonded interface, and the corresponding configuration for the master is ( /etc/sysconfig/network-scripts/ifcfg-bond0): TYPE=Bond BOOTPROTO=none DEFROUTE=yes IPV4_FAILURE_FATAL=yes NAME=bond0 DEVICE=bond0 ONBOOT=yes IPADDR=10.3.20.131 PREFIX=24

Hi, This may sound crazy but I will go ahead anyway. Here's my scenario: ifconfig bond0 10.10.10.1 netmask 255.0.0.0 ifenslave bond0 eth0 ifenslave bond0 eth1 brctl addbr stp0 brctl addif stp0 bond0 brctl stp stp0 on Is this a valid scenario? I am trying to bond two interfaces and run STP over the bonded interface..The problem I am trying to solve is to run STP over aggregated links

Hi all, i have a xen 4.3 installation and would like to have a bridge bond szenario: *** eth0 eth1 | | bond0 | br0 | vif = [ ''bridge=br0,mac=xx:xx:xx:xx:xx:xx'' ] *** With the network script in debian wheezy *** /etc/network/interfaces auto bond0 iface bond0 inet manual slaves eth0 eth1

Hi, I am currently struggling with the right way to configure a bonding device via kickstart (via PXE). I am installing servers which have "eno" network interfaces. Instead of the expected bonding device with two active slaves (bonding mode is balance-alb), I get a bonding device with only one active slave and an independent, non-bonded network device. Also the bonding device

I'm running into a situation where a bogus bonded interface named "bond0" is being created, in addition to the desired "bond2" interface. Can anyone confirm this? Anyone know why it's happening or what I do to get rid of it? I wanted to start my numbering scheme at 2 instead of 0, which I didn't think would be a problem. As you can see, I have no reference

Hi! Is it HTB fully compatible with BOND interface? I have this setup (mode= fault tolerance) : BOND0 -> ETH0 + ETH1 BOND1 -> ETH2 + ETH3 ( http://www.kernel.org/pub/linux/kernel/people/marcelo/linux-2.4/Documentation/networking/bonding.txt ) HTB work very well with Class over BOND0. If I add Class for BOND1 it generate balance errors. Also with HTB.init

Hi, I try to get networking running with xen 3.2, but it seems I fail miserably. I am on sles10sp1, with xen 3.2.0, and kernel rpm''s installed from SP2. I configured in /etc/sysconfig/network the NETWORK_LIST: NETWORK_LIST="bridge,0,default,00:DE:AD:BE:EF,192.168.8.13/24,dhcp-off" but an ifconfig xenbr0 still shows the mac address of peth0 fe:ff:ff:ff:ff:ff. Initially, I