similar to: Network scripts ifup-post

Requirement is a very strong word , but you should consider using it and here is a short demo why: - By default, RHEL uses NetworkManager to configure and manage network connections, and the /usr/sbin/ifup and /usr/sbin/ifdown scripts use NetworkManager to process ifcfg files in the /etc/sysconfig/network-scripts/ directory. [root at system ~]# ls -l /usr/sbin/ifup lrwxrwxrwx. 1 root root 22 21

Anyone know off the top of their head the "right" way to hard set a link automatically to 100Mbps Full Duplex, etc using the ifup or ifcfg files? Don't see options in the scripts that might cover this, but maybe there's a more elegant way to do it than to do something in rc.local or hack up the ifup files myself... Ray

I have been *manually* dealing with my wired and wireless network interfaces on my laptop. I have a pair of config files (in /etc/sysconfig/network-scripts/: ifcfg-eth0 (wired: Intel Corporation 82540EP Gigabit Ethernet Controller (Mobile)) and ifcfg-eth1 (wireless: Intel Corporation PRO/Wireless LAN 2100 3B Mini PCI Adapter), both with USERCTL=true (and ifcfg-eth0 also has ONBOOT=true). I have

Setting up bonding in active-backup mode 1 (using ARP monitoring) on a server, it looked OK, but pulling the active link cable didn't actually work, it didn't fail over. Eventually with manual playing around with modprobe, ifconfig, ifenslave, etc., a solution was stumbled upon: enslave the eth1 device before eth0, and all is good. Why this should matter is a puzzle - I could not find

My manager tells me a system in the datacenter is down. I go down there, and plug in a monitor-on-a-stick and keyboard. It's up, but no network. I try systemctl restart NetworkManager several times, and ip a shows *no* change. Finally, I do an ifdown, followed by an ifup, and everything's wonderful. My manager thinks that the NM daemon thinks everything's fine, and there've been

I and testing command line to up and down ethernet connection. if I perform following, client can not re-connect. ????? ifconfig eth0 down ????? ifconfig eth0 up if I use following, client can re-connect: ????? ifconfig eth0 down ????? ifup eth0 What difference between "ifconfig up" and "ifup"? thanks.

Odd situation: I've mentioned before that I have several users for whom I have to spoof the MAC address, due to a software license. Now, I've got net.ifnames=0 biosdevname=0 on the grub2 command line, and I've got the spoofed MAC address in /etc/sysconfig/network-sctipts/ifcfg-eth0. But he had a serious problem - X froze, and he thought to reboot, rather than call me. It came up with

Minor fix. I'm using this in my RPM specfile. John --- ./zaptel-1.0-RC1/Makefile.bigu 2004-07-16 17:09:07.000000000 -0500 +++ ./zaptel-1.0-RC1/Makefile 2004-08-18 16:28:45.000000000 -0500 @@@ -316,10 +318,10 @@ elif [ -d $(INSTALL_PREFIX)/etc/init.d ]; then \ install -m 755 zaptel.init $(INSTALL_PREFIX)/etc/init.d/zaptel;\ \ fi - if [ !

I'm looking for a capability similar to Debian/Ubuntu's pre/post up/down network commands capability. The problem: we've got a colo in which hosts talk directly to the hosting provider's router (through a bridging firewall) and hence our hosts MAC addresses are cached by the router. We should be able to solve this by pinging the router directly when bringing up the interface,

My machine has a static IP, with dhcp and IPv6 disabled. Every time I reboot, some process rewrites /etc/resolv.conf, including a comment about dhcpclient. The only package I have installed that shows up in "rpm -qa|grep -i dhcp" is dhcpv6-client-1.0.10-16.el5, and nothing in there is named dhcpclient. I'd like to figure out what software is rewriting this file and why. man 5

On Mon, Dec 02, 2019 at 06:51:44PM -0600, Michael Hennebry wrote: > I've chacked on that. > I've made what seemed like promissing changes to > /etc/sysconfig/network-scripts/ifup-post and > /etc/sysconfig/network-scripts/network-functions . > No go. > I still get the search line in resolv.conf . > I've tried putting in search google.com , > but on reboot, it

Dear Friends I have 2 netcards (eth0 to Internet and eth1 to internal network) in CENTOS 4.2, bit when I boot system the up eth0 and et1i [OK]. When I run ifconfig the eth1 has not IP configure, then I run command ifdown eth1 and ifup eth1, after eth1 is work perfect. Below I show file /etc/sysconfig/network-scripts/ifcfg-eth1 # Please read /usr/share/doc/initscripts-*/sysconfig.txt # for

Hello, I have a big problem with my servers. I have 4 NIC on all my KVM Servers but the most time on a start (restart) I lost one NIC? It is not always the same, but this two are virtio NICs. with ifup eth0(1) the system say,I have no configured eth0 or eth1 file ? Can any tell me what I can do? thank's for a answer NetworkManager is disabled. -- mit freundlichen Gr??en / best regards,

Hi, I'm running CentOS on all kinds of setups: servers, workstations, desktops and laptops. Up until now, I'm only using NetworkManager on laptops, since it makes sense to use it there. On servers and desktop clients, I usually remove it and configure the network "traditionally" by simply editing /etc/sysconfig/network-scripts/ifcfg-whatever, /etc/resolv.conf, /etc/hosts,

Hello all I am setting up a Centos 6 machine with one network card & one onboard network port. Both are recognized & work. Onboard Network port is unused yet, but is required for dedicated access to LTSP LAN, which would allow older PIII machines to boot from this system. I have installed LTSP but again Networking seems to be the problem area, as the clients won't boot from this

On Tue, Apr 21, 2015 at 03:46:52PM +0200, Dennis Jacobfeuerborn wrote: > Networking isn't really controlled by systemd but by NetworkManager. I > usually just yum remove NetworkManager* and then everything works just > as it did in CentOS 6. Note: NetworkManager is in CentOS6 too, and is part of the default workstation install. The NM in CentOS7 is a bit more polished than the NM

I want to change the contents of my /etc/sysconfig/static-routes-ipv6 and NOT restart the network. Is there a way to do this??? I know about ifup and ifdown for interfaces, but what about routing (and IP6 at that).

Hi all I have a SuSE 9.3 domU. It has a eth0 interface, corresponding to some vif interface in the dom0. Running ifup eth0 doesn''t seem to work. This means I don''t get any network. It seems that /sbin/ifup relies upon /sbin/getcfg but getcfg does not seem to find the right configuration for the eth0 device. A attached a patch below with a work around for this.

On 11/15/2016 06:07 AM, Sean Son wrote: > I have no network connectivity even > when I restart the network service. Should I reenable NetworkManager now? Yeah, the switch is just a test to see if the problem is specific to NetworkManager. It seems that you have other problems as well. Before you do that, post the output of the following: ip route show ip route show table 300 ip

On Sun, 4 Aug 2019, John Pierce wrote: > So you need to modify the source file that NetworkManager is using. > somewhere in /etc/network or /etc/networking-scripts, a config file has > DNS0=192.168.0.1 or sokmething, or your system is getting that from DHCP Will check on that. > the web login on 192.168.0.1 is undoubtably your modem/router. -- Michael hennebry at