similar to: SNMP V3 libraries not found, SNMPV3 disabled.

On Nov 30, 2017, at 6:31 PM, Lee Damon <nomad at ee.washington.edu> wrote: > > SNMPv3 works fine when I have any one of the three configured in > ups.conf while the other two are configured with SNMPv1. It doesn't > matter which _one_ UPS is configured for SNMPv3 in ups.conf, they all > work individually (see below example). > > However, if I configure any two or

nut-2.6.5 Scientific Linux 6.3 APC AP9630 management card My basic question is, does nut's SNMPv3 implementation work? I have this in /etc/ups/ups.conf ...... [tfapc01] driver = snmp-ups port = tfapc01.testfest.ixorg.org mibs = apcc snmp_version = v3 secLevel = authPriv secName = tfsnmpprof1 authPassword = ralow6moHet7zoboP8 privPassword = tuseL8Pakaz9degim7 authProtocol=MD5

New NUT install dealing with three APC Smart-UPS 5000s, two of which have AP9617 and the third has a AP9619 card. The SNMPv3 configurations on all three are exactly the same. This is confirmed by snmpget calls that work just fine: snmpget -Cf -v3 -u [...] -l authPriv -A '[...]' -X '[...]' -a MD5 -x DES [upsname] .1.3.6.1.4.1.318.1.1.1.1.1.1.0 snmp-ups can query all three

Updating an old thread. History here. http://lists.alioth.debian.org/pipermail/nut-upsdev/2013-January/006391.html http://lists.alioth.debian.org/pipermail/nut-upsdev/2013-February/006394.html http://lists.alioth.debian.org/pipermail/nut-upsdev/2013-February/006398.html On Fri, 1 Feb 2013, Tim Rice wrote: [snip] > > In all my testing I discovered the APC AP9630 is kind of flaky when >

Hi Charles, Running upsdrvctl -D start on the host with all three configured to SNMPv3 kicks out 56 different "unhandled ASN 0x81 from ..." lines on all three but importantly they all start up and keep running. I'm starting to suspect the startup is taking so long that systemd is timing out and killing it. time -p reports real time of 133.27. I'm not a fan of systemd but

I've told systemd to wait up to 10 minutes for startup but it's still failing. Sometimes it fails with "timeout exceeded" and sometimes with the ASN error previously reported. I went back to running upsdrvctl -D to see if I could see anything. On the third run I saw messages about "startup timer elapsed" for ups2-1 and then it tried again to launch that one (killing

Just a hunch about your snmpwalk, what happens if you format like this? snmpwalk -l authpriv -v 3 -u user -a MD5 -x DES -A authpassphrase -X privpassphrase {host address} so snmpwalk -l authpriv -v 3 -u nut -a MD5 -x DES -A NutScan at Password43LongerWord -X NutScan at Password43LongerWord apcups Thank you, David Zomaya Tripp Lite ________________________________ From: Nut-upsuser

I'm trying to get SNMPv3 management working for an APC AP9617 card. It is newly refurbed, running sumx v3.7.2 and aos v3.7.3. In the SNMPv3 user profiles section I have (I don't care about the password leaking, it's temporary): User Name: nut Authentication Passphrase: NutScan at Password43LongerWord Privacy Passphrase: NutScan at Password43LongerWord Authentication protocol:

Hi all. I am having an issue and quite frankly would rather not spend the entire next two days learning the entire snmp program. I am hoping someone out there has used MRTG and SNMP to make it work. I have both installed. Single server, polling itself. Question 1- does snmpd have to run as a daemon, or only run once so I can get OID and MIBs from it? Question 2- does anyone know the command

I got itchy fingers over the weekend and decided to fix what wasn't broken and upgraded one of the older servers from Centos 5.2 to Centos 5.3. Following the recommended process of updating glibc and such before the rest, it appeared to work perfectly and rebooted without problem. However, MRTG 2.15.2 started complaining about unexpected values. I installed/updated both MRTG (2.16.2) and

Hi David On 4/29/20 3:28 PM, David Zomaya wrote: > Is NUT using the same SNMP v3 user as your SNMP Set or a different one? > > If it is a different one (e.g. an SNMP v1 or v2c string) does that user > / community string have read/write access? I tried setting them all with -x thing= arguments as well as letting it pull from ups.conf, same result. It's all SNMPv3 settings. sudo

Hi gents, I have a CentOS 6.6 install with net-snmp running. I'm using SNMPv3 Auth and Encryption with Observium polling devices every five minutes. On one of my Centos server, the net-snmp process will die after 24-36 hours of running. It seems to be hitting my system maximum file open limit which is set to 1024. > [root at mail net-snmp-5.7]# ulimit -n > 1024 That number will

On Oct 9, 2014, at 5:33 PM, Brian Jester <bjester at spawar.navy.mil> wrote: > Charles, > > I re-ran, with no joy... here's my config.log. Seems to be a mismatch between the Net-SNMP package and your current compiler: configure:7857: checking for Net-SNMP version via net-snmp-config configure:7863: result: 5.6.1.1 found configure:7866: checking for Net-SNMP cflags

Hi Jim, On Tue, 18 Feb 2014, Jim Klimov wrote: > Hello all, > > I was asked about a proper way to ensure powerfail shutdown of a blade > server fed off an APC SmartUPS, which is monitored by all hosts over > SNMP. In particular, they'd like to avoid the "untimely" return of > utility power - when the OSes are already shutting down, and would > stay down

On Tue, 22 Jul 2008, tl wrote: > I search a simple variant to generate CPU,Load for MRTG. > Actually I use following configuration. > But I see CPU-usage of xen0 only, not a summary of all VM. > - net-snmp does not support xen [1]. > - dtc-xen [2] show CPU-usage from each VM, but not summary. > This view is confusing. [3] > For monitorings from more than 3 physical

Hallo xenusers, I search a simple variant to generate CPU,Load for MRTG. Actually I use following configuration. But I see CPU-usage of xen0 only, not a summary of all VM. - net-snmp does not support xen [1]. - dtc-xen [2] show CPU-usage from each VM, but not summary. This view is confusing. [3] For monitorings from more than 3 physical machines unpractically. - enomalism [4] is too large

Hi I''m trying to move the tracking of the shaping from MRTG to Cacti. My predecessor, who built all this stuff and was far more advanced than I, had a shell script that collected data by running tc -s qdisc show dev on both eth 0 and 1 and then pushing it out via snmp to another server running MRTG. I''m building a new server with cacti and having trouble with the custom

Is anyone using snmp-ups with the -k option successfully? This is really starting to look like a bug somewhere in nut, not a config problem. I've just tried the same command from a FBSD box with the same unfortunate result. Mind you, it could be the UPS card, I'm using the same one for both tests. : || nomad at castle nut-2.7.4 [93] ; please drivers/snmp-ups -a nutdev1 -x

On Jan 27, 2019, at 2:36 PM, Phil Stracchino <phils at caerllewys.net> wrote: > > SO, my full load on my core UPS is two Dell R610s, one Sun X4540, one HP > DL360p gen8, two six-core Thuban-II workstations plua their monitors, > and the network stack and KVM. > > The APC SU3000RM (3KVA) that blew up last week considered this to be > just short of 60% load. > The new

Hi I''ve patched net-mrtg http://www.net-snmp.org/ with http://x-ray.prokon.cz/data/snmp/ sucefully Also I''ve copied QOS.TXT to /usr/local/share/snmp/mibs when I make a normal use of snmp, with mrtg in order to monitor all traffic on eth0 and eth1, it works OK. But, how must I do in order to get monitor for a specific class ? If I make a snmpwalk (like README suggest), I get