similar to: [CentOS6] Manually configured Firewall (WLAN-AP plus Router)

1.. Is it even possible? Every example I've seen has bridged eth* rather wlan*. 2.. If it helps here are my scripts: $ more /etc/sysconfig/network-scripts/ifcfg-wlan0 ESSID="snip" MODE=Managed KEY_MGMT=WPA-PSK TYPE=Wireless BOOTPROTO=dhcp DEFROUTE=yes PEERDNS=yes PEERROUTES=yes IPV4_FAILURE_FATAL=yes IPV6INIT=no NAME=wlan0 UUID=2b508481-ec01-4311-8903-af7aaeb9879d ONBOOT=yes

Hello, I'd like to add rules (level workstation) for ignoring wlan reconnects/disconnects. The rules would ignore messages like this: May 12 11:02:16 t400 kernel: [13254.204101] No probe response from AP <MAC> after 500ms, disconnecting. May 12 11:02:16 t400 kernel: [13254.213029] cfg80211: Calling CRDA to update world regulatory domain May 12 11:02:16 t400 wpa_supplicant[3277]:

Hi All, After hours of reading and trials, I got the following setup working... 1. Dell Axim X30 PocketPC with 802.11b wireless using DHCP with Open WEP -- successfully connected to --> 2. Laptop with DLink Airplus DWL-650+ PCMCIA wireless with ndiswrapper v1.1 driver with network bridge (wired + wireless) and running a DHCP server listening on interface br0 (eth0 + wlan0) Here is the

Hi! I have some problems with an bridge between wlan0 and eth0 device... It works and I can from both sides ping the router with the bridge device but I cant ping the devices from other net so I cant ping wlan devs from eth net and other way around the wlan card is an atmel usbw11 from linksys and eth is a intel e100 10/100mbit nic I have configured the bridge according to the how to and

Hi all, let me see if I can explain my problem in an explicable way. I have written a WLAN driver which runs on a dedicated box (e.g. not a PCMCIA card). The box is plugged into a client that wants WLAN connectivity via Ethernet. E.g.: [ ] Ethernet [ ] RF/WLAN [ Laptop ]------------------[ WLAN adapter ]------------- [ ] [ ]

I have a Broadcom 802.11b/g hardware on my dual-boot laptop. Note first that in the WinXP partition, the wifi makes DHCP connections to my router with no problem. Since this was not working in my new CentOS 6 partition, and remembering that there was a driver problem with the old Fedora partition it replaced, I followed instructions founs at:

I am having problem in ping or connect AP from Mobile Node(essid & channel is the same,maybe routing did not set properly but i fail to configure with route add default gw 192.168.3.4,its alway said network is unreachable ),My Mobile Node is using acx100 as driver while AP(redhat 9.0) is using HOSTAP 0.1.3.Any one can help? I heard How-To said we not need to set address on eth0 & wlan0

ClarkConnect Home 3.2 eth0 - WAN - inet - ip:192.168.1.2 gw:192.168.1.1 (connected to my www.woosh.co.nz gatway) wlan - WAN - private community wireless networt - ip:10.252.16.16 gw:10.252.16.1 eth1 - LAN - ip:192.168.2.1 # route add -net 10.0.0.0 netmask 255.0.0.0 gw 10.252.16.1 [root@bowenvale etc]# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface

I intend to realize the connection to the Internet by WLAN (at the presen time DSL cable modem). The WLAN DSL-Router should not be the problem. But which wlan- adapter (internally (PCI), USB... whatever) can be recommended for a work "out of is the box" with cent OS 5? Thx Timothy

Hello, Thanx in advance to anyone who can help me get this going. I have tinkered around and around with this and I have it functioning as a visible access point that I can connect to. My problem comes in when trying to access the internet. I''m not an iptables guru or anything but I got the following as my iptables startup to supposedly masq the connection correctly:

Hi, i''m trying to use PCI passthrough feature on Xen 4.0 but it fails on my Wireless card. I use Xen 4.0 on a Debian 6.0 (package from repo) and try to passthrough the following PCI device root@omega:~# dpkg -l | grep xen ii libxenstore3.0 4.0.1-1 Xenstore communications library for Xen ii linux-image-2.6.32-5-xen-amd64 2.6.32-30 Linux 2.6.32 for 64-bit PCs, Xen dom0 support ii

Hi list, I bought two UTStarcom F1000 phones, pre-equipped with the latest firmware, including WPA support. Those are configured to register to an asterisk server on the internet (not LAN), and registration works. Calling and being called also, with transfer and all bells and whistles. After a few minutes up to 5 hours (varies widely), the display tells me that an Accesspoint is not available

I know, I know... don't use the non-standard kernels unless you have to... BUT: I have a D-Link N150 USB card. Bus 001 Device 004: ID 0846:9030 NetGear, Inc. WNA1100 Wireless-N 150 [Atheros AR9271] This isn't supported in C5, but it is supported in newer kernels (ath9k_htc). So let's try NDISwrapper: # rpm -i kmod\-ndiswrapper\-1.56\-1.el5.elrepo.i686.rpm

Gents, I have build a four interface firewall using Redhat V7.3 using a kernel supplied from the PoPTop website. Obviously I have poptop installed, and it seems to be working just fine. Anyway, I also have Shorewall installed, and it seems to be working just dandy except for one small problem. A little infor first. The interfaces/zones are ... net eth0 loc eth1 192.168.10.0/24 wlan eth2

Greetings, This is my fist time posting to a mailing list. For the past few days I have been trying to mimic my former windows workstation with a centos 6.3 workstation at work. I have gotten really far but am now facing an issue I cant seem to solve on my own. My former workstation had vmware for running my virtual machines. Most of the time I would run just two virtual machines, but sometimes

Hi to everyone on the mailing list. I have two networks at home, apart from the internet. One is the wired network, LAN, and the other is the wireless network, WLAN. They need to be separated, not bridged, because of hardware issues. I am trying to setup inter-networking browsing on these networks, pc's on LAN should see and browse pc's on WLAN and viceversa. After reading the manual

Hello. I have three separate networks on my LAN: wired network (192.168.0.0/24) wireless network (192.168.5.0/24) VPN (172.16.15.0/24) Here is an ASCII art showing my setup: ,----------. ppp0 <------eth1 eth0--192.168.0.0/24--->to LAN switch | wlan0--192.168.5.0/24---> WLAN | tun0--172.16.15.0/24---> VPN |__________|

Hello all, I'm trying to bridge the wlan0 and eth0 on an embedded system. I used the following commands to setup the bridge: ifconfig eth0 0.0.0.0 promiscuous ifconfig wlan0 0.0.0.0 promiscuous brctl addbr br0 brctl addif br0 eth0 brctl addif br0 wlan0 brctl sethello br0 1 brctl setmaxage br0 4 brctl setfd br0 4 ifconfig br0 up The eth0 is connected to a local network, and wlan0 is set to

Hallo, can I use pxelinux for booting a notebook via WLAN? Viele Gruesse! Helmut

Hopefully this is a simple answer. I am new to setting up bridges on a linux system. Here is what I have set up: Laptop directly connected to the eth0 port on the bridge (A Soekris 4521 board). The otherside of the bridge is a wirelass lan card (SMC2532b-w) as wlan0. The wlan0 is setup in managed mode to communicate to my test ap2000. When I do a 'brctl showmacs br0' on the