similar to: filesystem mounting fails at boot

_netdev The filesystem resides on a device that requires network access (used to prevent the system from attempting to mount these filesystems until the network has been enabled on the system). This device is not a network device (this a SAN not a NAS). To the OS it looks like a normal SCSI attached device, it's /dev/sdb. In the blade there is a HBA (Qlogic) card, and it's

On 10/10/2015 05:03 PM, Barry Brimer wrote: > On October 10, 2015 8:34:11 AM CDT, Imre Gergely <gimre at narancs.net> wrote: >> _netdev >> The filesystem resides on a device that requires network >> access (used to prevent the system from attempting to mount these >> filesystems until the network has been enabled on the system). >> >> This

Does it work usin netdev option? Eero 10.10.2015 4.17 ip. "Imre Gergely" <gimre at narancs.net> kirjoitti: > > Hi > > I have an IBM blade with internal harddisks, in hardware RAID1. I've > installed a CentOS 6 64bit on it, everything works just fine. > > After the installation, I've presented a vdisk to the blade from an > external SAN (an HP

On October 10, 2015 8:34:11 AM CDT, Imre Gergely <gimre at narancs.net> wrote: > > _netdev > The filesystem resides on a device that requires network >access (used to prevent the system from attempting to mount these >filesystems until the network has been enabled on the system). > >This device is not a network device (this a SAN not a NAS). To the OS >it

hi i downloaded dovecot-1.0.beta1.tar.gz, did a rpmbuild -ta dovecot-1.0.beta1.tar.gz (which uses the dovecot.spec from the tar.gz), and got the following: Making install in quota make[3]: Entering directory `/usr/src/gimre/rpm2/BUILD/dovecot-1.0.beta1/src/plugins/quota' make[4]: Entering directory `/usr/src/gimre/rpm2/BUILD/dovecot-1.0.beta1/src/plugins/quota' mkdir -p --

[offtopic] btw, is there something wrong with the domain? i couldn''t reach the site, my browser said the hostname lartc.org (or www.lartc.org) doesn''t exist, i had to dig up the ip address through whois, lookups and stuff. [/offtopic]

On 6/22/2016 11:06 AM, Digimer wrote: > I know this goes against the > grain of sysadmins to yank power, but in an HA setup, nodes should be > disposable and replaceable. The nodes are not important, the hosted > services are. of course, the really tricky problem is implementing an ISCSI storage infrastructure thats fully redundant and has no single point of failure. this requires

> On Oct 10, 2015, at 9:34 AM, Imre Gergely <gimre at narancs.net> wrote: > _netdev > The filesystem resides on a device that requires network > access (used to prevent the system from attempting to mount these > filesystems until the network has been enabled on the system). _netdev in fstab was a workaround from oracle linux support for a FC issue very similar

I have inherited an Oracle system which we have installed on a client site with the specs below. There was a kernel upgrade done by the patch management team at their site which broke the cluster. Once the kernel was reverted the system came back up. Am somewhat of a newbie to ocfs, etc and am trying to verify something. To do a kernel upgrade the ocfs2 (CRS) and ASM would have to be upgraded

hi i''m using htb + u32 filters, and i was wondering if there is something one can optimize at this stage. i have a lot of filters (~ 50.000 / interface, and there are two interfaces), and around 4500 classes / interface. the traffic going through this machine is something around 210-230mbit/s at 50kpps. as you can imagine, the load is pretty high. in fact (as it''s a dual xeon at

> Simple, it's only a NAS device, and not really a file server / web > server / data base server as well. Here is something I am currently lokoing at, and wondering if you'd considered it or if anyone here has done it. I've got a bunch of existing hardware - really good IBM stuff that is all installed with CentOS (with a few exceptions). We want to move to virtualization, but

I've setup the CentOS version of the RH Cluster Service on a pair of centos 4.4 i386 test boxes... wanting to do high availabilty stuff. its working, I've added a virtual IP and a fiberchannel hosted e3fs file system thhat either can mount, if I manually crash or reboot one, this IP and FS mount on the other, awesome. the servers are connected to the storage via a QLogic SANbox

Hi, I tried to do live migration from machine A to B. After the migration, machine A still had the record of the VM, though the VM was not running any more. Also, if I shut down the VM on machine B, its record on B would be gone --- I could not see it using "xm list" anymore. However, I can still start the VM on machine A using "xm start". Looks like the migration just move

Maybe I'm doing somthing really stupid, but while copying some windows share onto a samba server, on some random subdirectory robocopy says ERROR 87 (0x00000057) Copying NTFS Security to Destination Directory... The samba logfile has lots of these lines. modules/vfs_posixacl.c:349(smb_acl_to_posix) smb_acl_to_posix: ACL is invalid for set (Das Argument ist ung?ltig) The strange thing is

How does one configure a fence device in the form of a NIC card in centos 5? Is the gnbd item relevant to this? I have posted the question to linux-cluster also, but they are much less active overall, -so if you have info, massively appreciated... -karl

Is there a command that will list the disks that the system currently has? The df and mount commands only display info about filesystems. Charles L. Sliger, Information Systems Engineer, chaz at bctonline.com "No matter where you go, there you are..." -------------- next part -------------- An HTML attachment was scrubbed... URL:

I was wondering if anyone here has experience with HP MSA60 with P400 and P800 controller. How reliable are they for a 24x7 shop? TIA

Hello, I have a Rocks cluster based on Centos 5.2. Can this Centos version support a Storage Area Network? What kind of software do I need for installing and managing it? Regards, Panos Nastou Dpt of Mathematics Aegean University Samos Island Greece

From: Bruno Delbono <bruno.s.delbono at mail.ac> > I'm really sorry to start this thread again but I found something very > interesting I thought everyone should ^at least^ have a look at: > http://uadmin.blogspot.com/2005/06/4-dual-xeon-vs-e4500.html > This article takes into account a comparision of 4 dual xeon vs. e4500. > The author (not me!) talks about "A

Hi list, Trying to set custom paramters for a wine-program as wcmd for example doesn't work for me. I tried setting [AppDefaults\\wcmd.exe.so\\x11drv] "Desktop"= "N" and [AppDefaults\\wcmd.exe\\x11drv] "Desktop"= "N" when global is "Desktop"="640x480". wcmd is displayed on a 640x480 desktop. Is there a workaround ?