similar to: Remote auth against Active Directory

I'm looking for direction to install and boot CentOS 7 from an iSCSI device. Any experience and advice will be greatly appreciated. Thanks! Michael Duvall

Hello All, I seem to have run into a bug with the new --bridgeslaves=<INTERFACE> option. It would seem that if I tell the bridge device to use a virtual interface (like bond0) rather than a physical interface (em1/em2) that kickstart completely barfs on it. I have provided my network section below which works fine as long as i don't enable all the bridge content. When the

I'm poking through Solaris documentation trying to figure out how to make it installable via our PXE server and, as with many things Solaris, I'm hitting walls of completely foreign procedures and setups. Has anyone managed to do this before? I'm trying to set Solaris 11.3 up.

----- Original Message ----- From: "John Hodrien" <J.H.Hodrien at leeds.ac.uk> To: "CentOS mailing list" <centos at centos.org> Sent: Thursday, August 18, 2016 4:47:09 PM Subject: Re: [CentOS] Centos7 kickstart & pxe On Thu, 18 Aug 2016, johan.vermeulen7 at telenet.be wrote: > Hello All, > > I'm trying to get kickstart to work through pxe. > So

On 8/4/2015 12:47 PM, James A. Peltier wrote: > Some older 32-bit software will likely have problems addressing any content outside of the 2^32 bit inode range. You will be able to see it, but reading and writing said data will likely be problematic The 99% of software that just does open,read,write will be fine regardless of word size. NFS is the only broken thing I ran into (on CentOS 6

Hi All, I have a Dell R710 that has 6x1TB in a RAID-5 configuration. When installing CentOS 7 using the full disk capacity and booting in UEFI mode the machine dumps me into a GRUB rescue mode prompt. error: disk `,gpt2' not found Entering rescue mode... grub rescue> If I use the PERC RAID controller to make the disk smaller ROOTDISK volume of 100GB in size and then a DATA volume

Hi, I've created a bridge using 2 interfaces and have a lot of messages as follows: nov 12 15:30:22 localhost kernel: br0: received packet on enp0s3 with own address as source address nov 12 15:30:22 localhost kernel: br0: received packet on enp0s3 with own address as source address And the operating systems is extremely slow Interfaces files : [root at localhost ~]# cat

2015-11-12 18:07 GMT-03:00 James A. Peltier <jpeltier at sfu.ca>: > ----- Original Message ----- > | Hi, > | > | I've created a bridge using 2 interfaces and have a lot of messages as > | follows: > | > | nov 12 15:30:22 localhost kernel: br0: received packet on enp0s3 with own > | address as source address > | nov 12 15:30:22 localhost kernel: br0: received

On 6/25/2015 8:50 AM, Robert Heller wrote: > man vgdisplay > man lvdisplay > man lvcreate > man lvextend > man lvresize > man lvreduce > man lvremove > man e2fsck > man resize2fs man xfs_growfs -- john r pierce, recycling bits in santa cruz

Through kickstart I setup everything I need. On CentOS 7 I still get the "welcome" screen followed by a couple more then your ready to start using centos how do I get Rid of those series of screens ? Thanks Jerry

I have just started looking through the RHEL6 IdM guide, and while the documentation seems quite thorough and extensive, the examples are somewhat on the weak side. Migration scenarios can be much more complex - e.g. migrating away from NIS while at the same time moving to LDAP or AD for user account management. Is anyone aware of any tutorials or guidelines for such a situation? Then there are a

Is DLZ support enabled in the Centos 7 bind? building a Samba/sernet AD, and this looks to be the best way to handle the DNS needs of the AD. thanks. Also any web tools for managing a mysql (mariaDB?) DLZ backend? Web, as my AD will not have a GUI; nor should I be doing this on the AD directly.

On 08/27/2015 12:49 PM, James A. Peltier wrote: > ----- Original Message ----- > | Is DLZ support enabled in the Centos 7 bind? > | > | building a Samba/sernet AD, and this looks to be the best way to handle > | the DNS needs of the AD. > | > | thanks. > | > | Also any web tools for managing a mysql (mariaDB?) DLZ backend? Web, as > | my AD will not have a GUI; nor

Gordon Messmer wrote: > On 09/16/2015 09:11 AM, Callum Scott wrote: >> It is running a little >> tight on memory and so there have been a couple of events where the >> OOM_killer has been invoked and killed off MySQL, which you would >> expect. > > One thing that should be noted is that regardless of swappiness, > overcommit might be an issue. If a single

On Tuesday 26 September 2017 11:56:06 Joseph L. Casale wrote: > The error is actually pretty straight forward. You are using a repo > (atrpms) that has not been updated in years, it's not surprise that it > finally has lost compatibility with the platform. > > Find a modern and up to date replacement for any packages you reference > from atrpms and without the switches. When

----- Original Message ----- | Not tried automount with Centos 7 nor with selinux. | | With that said autofs relies on nfs mounting to work, so have you | started there by attempting to manually mount /home? | | Another place to look is at the hostname. I've had problems where auto | mount doesn't like the short name and insists on using a FQDN, to get | around that you could try using

On Monday, 08 June 2015 at @07:06 zulu, Gordon Messmer wrote: > Why? If you use gparted (ntfsprogs, under the covers, IIRC), the system > will chkdsk on the next boot. No such requirement exists with Microsoft's > tools That's not been my experience... gparted does use ntfs-3g to work on NTFS partitions (what linux-based tool doesn't?), but does not by default set the

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 On 25/08/15 23:09, Fabian Arrotin wrote: > On 25/08/15 20:39, Alice Wonder wrote: >> julie70773 [at] loverhearts.com > >> Responded off-list to message on the list, spam with content >> that is not suitable for minors. > >> It is possible subscribed under different address. > >> IP of offending spam : >

Hi All I have two bond interfaces namely, bond0 and bond1. bond0 has two ethernet interfaces associated with it and bond1 also has two ethernet interfaces associated with it. Now i create a bridge interface namely br20 (20 being the VLAN) and assign it a IP Address , subnet mask and the default gateway. I will use this IP to reach the server. So it is like a management bridge for me.

On 27/06/2017 00:49, James A. Peltier wrote: > Bind does not have a method to do multi-master replication. All updates must be done via an intermediary service (database). > > In our case, we've used containers and Consul for providing a highly available DNS service. A container will fire up and race for the master lock. It will dump the contents of the database into its named