similar to: C7 and /etc/sysconfig/network

I wasn't sure what to call this in the subject line, but here's my issue. I have an occasional need to switch a few computers from one Internet provider to a different one. Both Internet providers feed into the same network, one at 192.168.0.1 and the other at 192.168.0.254. So to change from one provider to the other I run nmtui to change the gateway and dns server addresses, then

On Thu, Apr 7, 2016 at 1:26 PM, Subscriber <ml-lists at agoris.net.ua> wrote: > Hello FrancisM, > > Thursday, April 7, 2016, 8:03:38 AM, you wrote: > > > > I tried last night and it seems like the vlans that I created is failing > to > > bring-up. So this is what Im doing > > > in my DATA trunk port at my HomeLab Im doing this > > > 2 port

Once again I am building a headless Centos 7 box that needs to reliably be on both the LAN and WIFI network at all times. Amongst other things it's going to be an AirPrint bridge enabling IPads to print to printers on a different VLAN. I have asked about this before and got a solution working using nmtui to set up both the LAN and WIFI interface, and activate them. However, the WIFI

On 8/25/2015 11:58 AM, Robert Moskowitz wrote:> Does Centos 7 use /etc/sysconfig/network or is this replaced by some > systemctl set of commands. I let Network Manager control the interfaces on my two or three C7 boxes. I used nmtui to set the hostname, and MAC and IP addresses (the MAC addresses need to be updated if you clone a machine in VMware) interactively. That's not

On Thu, 16 Jan 2020 15:34:43 +0100, Stephen John Smoogen <smooge at gmail.com> wrote: > On Thu, 16 Jan 2020 at 07:58, Asle Ommundsen <aommundsen at gmail.com> > wrote: >> >> Hi, >> >> Tonight I upgraded two CentOS 8 boxes to CentOS 8.1 (1911). Then after a >> reboot of the first server the network was unavailable. In IPMI console >>

Hello everyone Iam trying to delete a route from mt CentOs 7 server but everytime i restart network services, it reappears iam using command "route del -net x.x.x.x/x gw x.x.x.x <interface name>" Am i missing something?? Best Regards Mulin

I gather that ifconfig is a way of setting the netmask in the current shell instead of a persistent value.? I say this because I am running it and see it for my specific network interface, directly after running it. However if I restart the network service the netmask is reverted to the previous value. What is the correct way to set the new netmask for the network interface to make it persistent.

We can permanently set hostname using hostnamectl set-hostname. How can we permanently set *domain name* in CentOS 7? I found an article <http://unix.stackexchange.com/questions/239920/how-to-set-the-fully-qualified-hostname-on-centos-7-0> that recommended setting FQDN using hostnamectl. Is that the right way to set hostname and domainname at the same time using *hostnamectl set-hostname*

On 04/26/2015 07:37 PM, Frank Cox wrote: > On Sun, 26 Apr 2015 19:25:27 -0500 > Robert Nichols wrote: > >> Do you know of a place I can set a static name that NetworkManager >> won't override? > > What about this: > > hostnamectl set-hostname whateveryouwant # which hostnamectl /usr/bin/which: no hostnamectl in

Hi, Tonight I upgraded two CentOS 8 boxes to CentOS 8.1 (1911). Then after a reboot of the first server the network was unavailable. In IPMI console everything except the network was looking good. Network was unreachable. No errors in NetworkManager. I also restarted NetworkManager, but it did not help. Then I discovered that the default gateway suddenly was missing. Then I rebooted the

Dear CentOS-Community, we are facing the following issue: A secondary ip address seems to be automatically added to a nic which causes several issues in our setup. This server is equipped with four nics which are currently in use: # nmcli con show NAME????? UUID????????????????????????????????? TYPE????? DEVICE eno2????? cb6fcb54-be52-4ab6-8324-88091a0ea1a0? ethernet? eno2 eno4?????

Once upon a time, Lists <lists at benjamindsmith.com> said: > I understand that it's possible to allow the 4 VM guest systems to each have a > "direct" fixed IP address and access the addresses \via the host network > adapter, while the host retains its fixed IP. If you are running NetworkManager (the default), it's not too hard. Here's an example

Hi, I have to do some maintenance on a CentOS 7 proxy installed on a routerboard without a video card. The only way to access this machine directly is via Minicom and serial port. I'm using NetworkManager TUI (nmtui) to configure network interfaces, but Ncurses rendering in Minicom works in the sense that chickens fly and horses swim. What you get is a forest of question marks with a few

In CentOS 6.7 I ran setup command and I could configure network settings from that "gui" utility at command line. In CentOS 7 I don't know where this goes or how to enabled. I have installed a few packages: yum install setuptool -y \ && yum install system-config-network-tui -y \ && yum install system-config-firewall* -y \ && yum install

On Tuesday 10 January 2017 08:53:17 John R Pierce wrote: > On 1/9/2017 7:11 PM, fred roller wrote: > > On Mon, Jan 9, 2017 at 12:04 PM, Frank Cox<theatre at melvilletheatre.com> > > > > wrote: > >> That sounds like a weak signal from your wifi transmitter. > > > > Or signal interference. Where is the antennae located on the server? > > Ran

On Tue, Apr 21, 2015 at 03:46:52PM +0200, Dennis Jacobfeuerborn wrote: > Networking isn't really controlled by systemd but by NetworkManager. I > usually just yum remove NetworkManager* and then everything works just > as it did in CentOS 6. Note: NetworkManager is in CentOS6 too, and is part of the default workstation install. The NM in CentOS7 is a bit more polished than the NM

Le 18/02/2020 ? 12:28, Anand Buddhdev a ?crit?: > Neither. The DNS configuration should not normally be bound to a > specific interface, so don't configure it with any interface. If you do, > and that interface goes down, your DNS config also disappears. I would like to do that very much, only NetworkManager makes you jump through burning loops to do so. With network-scripts, it

My manager tells me a system in the datacenter is down. I go down there, and plug in a monitor-on-a-stick and keyboard. It's up, but no network. I try systemctl restart NetworkManager several times, and ip a shows *no* change. Finally, I do an ifdown, followed by an ifup, and everything's wonderful. My manager thinks that the NM daemon thinks everything's fine, and there've been

Hai Viktor,   Yes, i did keep that in mind that it was an upgrade, that exact why im responding. ;-)   If in the base  /etc/hostname, /etc/nsswitch.conf and /etc/resolv.conf or systemd  cointains wrong settings, you might inherit these. So it might be that a previous samba was accepting these settings, but a latest samba not. Or a previous systemd version accepted these and a newer not..  

On 28/08/15 13:15, Robert Moskowitz wrote: > In the shower this morning, I realized that samba's dlz is through its > ldap interface, probably through dhcp. :) > > All of that work researching how to set up a dlz database for naught. > This is NOT documented in either: > > https://wiki.samba.org/index.php/DNS > or >