similar to: 7.1 install with Areca arc-1224

On 07/06/15, g wrote: you might try verifying that system you are getting error message on has a good cd/dvd drive. burn another dvd at at least 4 speeds slower. if runs ok, bad drive. if still fails, bad drive. another way you can check is to pull iso on system you are having problem with and burn dvd. if you get error, get a new drive. -------- Above quoted -------- When I md5sum the DVD

On 07/05/2015 09:17 AM, linush at verizon.net wrote: > Someone please tell me what I did to screw this thing up so badly. On 07/05/15, Gordon Messmer<gordon.messmer at gmail.com> wrote: Have you looked at the log files in /mnt/sysimage/root/? ------------- Quoting broken in this mailer ------------ So I looked in /mnt/sysimage/var/log/anaconda and found this in anaconda.packaging.log:

On 07/05/15, Gordon Messmer wrote: anaconda will try to delete an rpm file if it gets an IOError. Your media may be corrupt. Check that first. ----- Above quoted ----- No such luck. On the system where I'm doing the install, I used dd to read the entire DVD and also copied every .rpm to /dev/null and didn't get any I/O errors. What next?

I must be doing something horribly wrong and I hope somebody can help. The Areca arc-1224 is not supported by the Areca driver included driver in 7.1 so I have to supply that when starting the install. Documentation provided by Areca and in the Red Hat install guide say the same thing, put the driver on an accessible medium then append inst.dd on the boot command, choose the driver and now the

On 07/06/15 18:06, C Linus Hicks wrote: > On 07/06/15, g wrote: >> you might try verifying that system you are getting error message on >> has a good cd/dvd drive. >> >> burn another dvd at at least 4 speeds slower. >> > if runs ok, bad drive. >> > if still fails, bad drive. >> > another way you can check is to pull iso on system you are

Running C6 fileserver. Want to replace 7 year old HDs connected to an Areca ARC-1220 raid sata II (3Gb/s) controller. Has anyone used this controller with newer 2TB SATA III (6Gb/s) WD Re drives like the WD2000FYYZ or the WD2004FBYZ?

> The disks I am going to use are 6TB Seagate Enterprise ST6000NM0034 > 7200rpm SAS/12Gbit 128 MB Sorry to hear that, my experience is the Seagate brand has the shortest MTBF of any disk I have ever used... > If hardware RAID is preferred, the controller's cache could be updated > to 4GB and I wonder how much performance gain this would give me? Lots, especially with slower

> This is why before configuring and installing everything you may want to > attach drives one at a time, and upon boot take a note which physical > drive number the controller has for that drive, and definitely label it so > y9ou will know which drive to pull when drive failure is reported. Sorry Valeri, that only works if you're the only guy in the org. In reality, you cannot

On 2017-01-20, Valeri Galtsev <galtsev at kicp.uchicago.edu> wrote: > > Hm, not certain what process you describe. Most of my controllers are > 3ware and LSI, I just pull failed drive (and I know phailed physical drive > number), put good in its place and rebuild stars right away. I know for sure that LSI's storcli utility supports an identify operation, which (if the

On Sat, January 21, 2017 12:16 am, Keith Keller wrote: > On 2017-01-20, Valeri Galtsev <galtsev at kicp.uchicago.edu> wrote: >> >> Hm, not certain what process you describe. Most of my controllers are >> 3ware and LSI, I just pull failed drive (and I know phailed physical >> drive >> number), put good in its place and rebuild stars right away. > > I

Hello, I have a RAID-6 Partition with the Areca ARC-1231 card on a S5000PAL Intel system with 6 disks as part of the raid volume. The system has been set up as Write-back cache and the raid card has a 2 GIG memory cache on it. It is installed on Freebsd 7.0 STABLE with SCHED_ULE enabled. I have a folder with a lot of small and big files in it that total 3009 files. In the user system we

Hi Valeri, Before you pull a drive you should check to make sure that doing so won't kill the whole array. MegaCli can help you prevent a storage disaster and can let you have more insight into your RAID and the status of the virtual disks and the disks than make up each array. MegaCli will let you see the health and status of each drive. Does it have media errors, is it in predictive

On Fri, January 20, 2017 12:59 pm, Joseph L. Casale wrote: >> The disks I am going to use are 6TB Seagate Enterprise ST6000NM0034 >> 7200rpm SAS/12Gbit 128 MB > > Sorry to hear that, my experience is the Seagate brand has the shortest > MTBF > of any disk I have ever used... > >> If hardware RAID is preferred, the controller's cache could be updated >> to

Hi, Does anyone have experiences about ARC-1883I SAS controller with CentOS7? I am planning to have RAID1 setup and I am wondering if I should use the controller's RAID functionality which has 2GB cache or should I go with JBOD + Linux software RAID? The disks I am going to use are 6TB Seagate Enterprise ST6000NM0034 7200rpm SAS/12Gbit 128 MB If hardware RAID is preferred, the

On Fri, January 20, 2017 7:00 pm, Cameron Smith wrote: > Hi Valeri, > > > Before you pull a drive you should check to make sure that doing so > won't kill the whole array. Wow! What did I say to make you treat me as an ultimate idiot!? ;-) All my comments, at least in my own reading, we about things you need to do to make sure when you hot unplug bad drive it is indeed failed

On Fri, January 20, 2017 5:16 pm, Joseph L. Casale wrote: >> This is why before configuring and installing everything you may want to >> attach drives one at a time, and upon boot take a note which physical >> drive number the controller has for that drive, and definitely label it >> so >> y9ou will know which drive to pull when drive failure is reported. > >

this is cleaner and avoids rebuilding initramfs in the kickstart post it is built with correct configuration for the node image the first time, in kernel posttrans --- dracut/Makefile.am | 3 + ...-3d88d27810acc7782618d67a03ff5c0e41494ca4.patch | 20 ++++++++ ...-93724aa28fc20c8b7f0167201d1759b7118ba890.patch | 37 +++++++++++++++ dracut/ovirt-dracut.conf

Hi, My first e-mail... my apologies if this is not the appropriate e-mail list. My goal is to *write* from the guest OS to a CD or DVD reader/writer on my host system. Currently, the write operation is failing. I believe it is because the virtual CD-ROM device is set to be "readonly". Is it possible to write to a QEMU CDROM device and, if so, how? (The host machine's CD-ROM

Hi. I'm looking at deploying a freebsd 7-release server with some storage attached to an areca ARC-1680 controller. But this card is not mentioned in 'man 4 arcmsr' (http://www.freebsd.org/cgi/man.cgi?query=arcmsr&sektion=4&manpath=FreeBSD+7.0-RELEASE). Areaca's website does mention freebsd as a supported OS (http://www.areca.com.tw/products/pcietosas1680series.htm). Has

Just as I create a ZFS pool and copy the root partition to it.... the performance seems to be really good then suddenly the system hangs all my sesssions and displays on the console: Oct 10 00:23:28 sunrise arcmsr: WARNING: arcmsr0: dma map got ''no resources'' Oct 10 00:23:28 sunrise arcmsr: WARNING: arcmsr0: dma allocate fail Oct 10 00:23:28 sunrise arcmsr: WARNING: arcmsr0: