Displaying 20 results from an estimated 1000 matches similar to: "Centos 6 - Persistant static routes"
2015 Mar 12
3
Centos 6 - Persistant static routes
On Mar 12, 2015, at 11:52 AM, Jason Warr <jason at warr.net> wrote:
>
> On Thu, 12 Mar 2015 12:43:27 -0500, Robert Moskowitz <rgm at htt-consult.com> wrote:
>
>> I found:
>>
>> http://www.cyberciti.biz/tips/configuring-static-routes-in-debian-or-red-hat-linux-systems.html
>>
>> where it says to add to ifcfg-eth0:
>>
>>
2009 Apr 28
2
adding static route via network setup fails
I want to add the following route command
route add -net 192.168.2.0/27 gw 192.168.2.3
via the normal network setup.
The result should be the following routing table (the first line):
192.168.2.0/27 via 192.168.2.3 dev xenbr1 scope link
192.168.2.0/27 dev eth2 proto kernel scope link src 192.168.2.4
192.168.2.0/27 dev xenbr1 proto kernel scope link src 192.168.2.3
192.168.1.0/24 dev xenbr0
2015 Feb 19
3
Help with routing question.
On Wed, February 18, 2015 13:07, Les Mikesell wrote:
> On Wed, Feb 18, 2015 at 11:39 AM, James B. Byrne
> <byrnejb at harte-lyne.ca> wrote:
>> 2. How does one configure the routing table on network startup to
>> specifically detail the route particular addresses are supposed to
>> take?
>>
>
> Not exactly sure how routing works with aliases on the same
2015 Feb 20
1
Help with routing question.
On Thu, February 19, 2015 12:33, Les Mikesell wrote:
> On Thu, Feb 19, 2015 at 9:48 AM, James B. Byrne
> <byrnejb at harte-lyne.ca> wrote:
>>
>>> I added these directives to the route-eth0:192 file:
>>>
>>> ADDRESS0=192.168.6.9
>>> NETMASK0=255.255.255.0
>>> GATEWAY0=192.168.6.1
>>>
>>
>> Which should have been:
2015 Mar 12
2
Centos 6 - Persistant static routes
On 03/12/2015 03:51 PM, Les Mikesell wrote:
> On Thu, Mar 12, 2015 at 2:25 PM, Warren Young <wyml at etr-usa.com> wrote:
>> On Mar 12, 2015, at 11:52 AM, Jason Warr <jason at warr.net> wrote:
>>> On Thu, 12 Mar 2015 12:43:27 -0500, Robert Moskowitz <rgm at htt-consult.com> wrote:
>>>
>>>> I found:
>>>>
>>>>
2015 Mar 12
0
Centos 6 - Persistant static routes
On Thu, 12 Mar 2015 12:43:27 -0500, Robert Moskowitz <rgm at htt-consult.com>
wrote:
> I know how to use 'ip' to set up a static route, e.g.:
>
> ip route add 192.168.128.0/17 via 40.53.24.3 dev eth0
>
> But if you reboot or restart network, you loose this. Thus you have to
> make it persistant. I found:
>
>
2015 Mar 12
0
Centos 6 - Persistant static routes
On Thu, Mar 12, 2015 at 2:25 PM, Warren Young <wyml at etr-usa.com> wrote:
> On Mar 12, 2015, at 11:52 AM, Jason Warr <jason at warr.net> wrote:
>>
>> On Thu, 12 Mar 2015 12:43:27 -0500, Robert Moskowitz <rgm at htt-consult.com> wrote:
>>
>>> I found:
>>>
>>>
2014 Aug 27
2
Cannot Static Routes
Hi,
I'd want to configure persistent static routes, ie in config files, but I
can't configure static routes, I tested:
[root at centos7 ~]# cat /etc/sysconfig/network-scripts/routes-enp0s3
ADDRESS0=10.10.10.0
NETMASK0=255.255.255.0
GATEWAY0=192.168.1.1
logs says nothing:
ago 27 15:38:29 centos7.vhgroup.corp NetworkManager[2299]: <info>
Activation (enp0s3) Stage 5 of 5 (IPv4
2015 Mar 13
0
Centos 6 - Persistant static routes
On Thu, Mar 12, 2015 at 01:43:27PM -0400, Robert Moskowitz wrote:
> I know how to use 'ip' to set up a static route, e.g.:
>
> ip route add 192.168.128.0/17 via 40.53.24.3 dev eth0
>
> But if you reboot or restart network, you loose this. Thus you have
> to make it persistant. I found:
>
>
2005 Dec 12
1
Netcard don't up
Dear Friends
I have 2 netcards (eth0 to Internet and eth1 to internal network) in
CENTOS 4.2, bit when I boot system the up eth0 and et1i [OK].
When I run ifconfig the eth1 has not IP configure, then I run command
ifdown eth1 and ifup eth1, after eth1 is work perfect.
Below I show file /etc/sysconfig/network-scripts/ifcfg-eth1
# Please read /usr/share/doc/initscripts-*/sysconfig.txt
# for
2015 Mar 12
0
Centos 6 - Persistant static routes
On 12 March 2015 at 13:43, Robert Moskowitz <rgm at htt-consult.com> wrote:
> I know how to use 'ip' to set up a static route, e.g.:
>
> ip route add 192.168.128.0/17 via 40.53.24.3 dev eth0
>
> But if you reboot or restart network, you loose this. Thus you have to
> make it persistant. I found:
>
>
2008 Apr 15
1
How to create static routes on startup with CentOS4?
Hi,
I'm working with the iproute2/iptables toolset on my CentOS4 server to
create custom routing rules. However, I'm a bit at a loss how to create
these permanently so that they are automatically reloaded upon reboot of the
server.
I know that iptables has a config file in /etc/sysconfig/iptables that is
loaded by /etc/init.d/iptables startup script.
Is there anything that works
2005 Aug 05
5
making a route sticky
Is it possible to have a route stick in the kernel, even if device it points to
goes to roller coaster up and down drive.
For example. I have an ADSL modem and am doing VPN over it. There's a route
needed for VPN added like this:
ip route add 192.168.1.0/24 via 1.2.3.4 src 192.168.2.1
There are two problems with it:
a) if ADSL link is down when above command is executed, the route
2015 Mar 12
0
Centos 6 - Persistant static routes
On Thu, Mar 12, 2015 at 3:01 PM, Robert Moskowitz <rgm at htt-consult.com> wrote:
>
>>>>>
>>>>> where it says to add to ifcfg-eth0:
>>>>>
>>>>> 192.168.128.0/17 via 40.53.24.3
>>>
>>> That?s only for RHEL 7: http://goo.gl/AtjIyI
>>
>> Aside from being irritating, that's just wrong. I'm
2015 Mar 12
1
Centos 6 - Persistant static routes
On 03/12/2015 04:12 PM, Les Mikesell wrote:
> On Thu, Mar 12, 2015 at 3:01 PM, Robert Moskowitz <rgm at htt-consult.com> wrote:
>>>>>> where it says to add to ifcfg-eth0:
>>>>>>
>>>>>> 192.168.128.0/17 via 40.53.24.3
>>>> That?s only for RHEL 7: http://goo.gl/AtjIyI
>>> Aside from being irritating, that's just
2015 Feb 19
0
Help with routing question.
On Thu, February 19, 2015 10:19, James B. Byrne wrote:
>
> I added these directives to the route-eth0:192 file:
>
> ADDRESS0=192.168.6.9
> NETMASK0=255.255.255.0
> GATEWAY0=192.168.6.1
>
Which should have been:
ADDRESS0=192.168.6.0
NETMASK0=255.255.255.0
GATEWAY0=192.168.6.1
Sigh.
--
*** E-Mail is NOT a SECURE channel ***
James B. Byrne
2007 Jun 22
0
Bug in initscripts? Problem with ifup-routes and alias device
Hello List,
I have one network card and added two IP-Adresses to it:
eth1 192.168.1.1/24
eth1:1 10.1.2.3/24
a want to use static routes on device eth1:1 and added one in
/etc/sysconfig/network-scripts/route-eth1:1:
GATEWAY0=10.1.2.4
ADDRESS0=10.2.2.0
NETMASK0=255.255.255.0
What the network-script should execute in background is:
ip route add 10.2.2.0/24 via 10.1.2.4 dev eth1
but it executes
2009 Jul 22
1
Routing issue - Revisited
A number of weeks ago I had huge help from many of you configuring routing
on a server with multiple Internet facing nics. Thanks for all of your
help!!!!
I am still having a routing issue that I am hoping someone can help me
tweek. This server, besides acting as our gateway to the internet, is also
our web and email server. The server has 4 nics. Two are connected to the
internet and the
2013 Oct 04
1
networking issues - internet facing guest interfaces
I have the following networking setup:
- eth0 and eth1 corresponding to the physical ports on the host NIC
- bond0 which enslaves eth0 + eth1
- br0 which attaches bond0
- xenbr0 - xenbr5 all of which are internal only networks (10.0.0.0;
10.1.1.0; etc)
Br0 is used both for the host to access the outside world as well as DomUs
acting as gateway machines for each xenbr network. For example the
2006 Dec 14
5
persistant: Matlab->R
Dear list members,
Could anyone tell me if there is an equivalent of the Matlab declaration 'persistant' in R?
Thank you very much,
Bernard Gregorry.
(Matlaber converted to R).
---------------------------------
[[alternative HTML version deleted]]