similar to: Centos 6 - disabling IPv6 addressing

Sorry - that should be sysctl -w net.ipv6.conf.all.accept_ra=0 to disable that, not 1. Chris On Sun, Mar 8, 2015 at 11:14 PM, Chris Stone <axisml at gmail.com> wrote: > Try: > > sysctl -w net.ipv6.conf.all.accept_ra=1 > > to persist between boots, be sure to add this to your /etc/sysctl.conf > file. > > This should prevent the box from listening to any RA

How about, in your /etc/sysconfig/network file adding or editing the line for IPV6 to be: NETWORKING_IPV6=no and then try a 'service network restart' and see what you get. Chris On Mon, Mar 9, 2015 at 11:52 AM, Robert Moskowitz <rgm at htt-consult.com> wrote: > No change after running this and trying both: > > system network restart > > ifdown eth0; ifup eth0

On Fri, Mar 6, 2015 at 11:52 AM, Robert Moskowitz <rgm at htt-consult.com> wrote: > > > On 03/06/2015 11:00 AM, Robert Moskowitz wrote: > >> >> >> On 03/06/2015 10:55 AM, Barry Brimer wrote: >> >>> >>> >>> IPV6INIT="no" >>>> >>>> But I am still getting a global IPv6 (and of course local scope).

On 03/06/2015 10:55 AM, Barry Brimer wrote: > > >> IPV6INIT="no" >> >> But I am still getting a global IPv6 (and of course local scope). >> >> What else do I need to do to disable the listening for RA announcements >> >> and setting an IPv6 global address? I do not want to reboot the box. > There are other modules, most notably bonding

On 03/06/2015 10:40 AM, Robert Moskowitz wrote: > I have just moved a host from a network that supports static IPv4 and > IPv6. The IPv4 addr is set in ifcfg-eth0, and the IPv6 via RA (I set > the MAC so I get an IPv6 addr that I like). > > I just moved the host to a network that supports static IPv4, but only > dymanic IPv6, so at this time (until I get static IPv6), I need to

On 4/28/2020 3:17 PM, Chris Adams wrote: > - gateway sends a router solicitation and gets a router advertisement > with "stateful config" set, which tells gateway to do DHCPv6 (but > default route comes from RA) I'm not seeing any outbound IPv6 traffic from my CentOS 7 box on the WAN interface. I do see RA's emitting from the LAN interface, from radvd. Is there

Dear Simon, every second IP-address is unwanted. We restarted? eno4: nmcli con down eno4; nmcli con up eno4 and the second address vanishes. Then after a few ours, the second ip address reappears. This is the config-file of eno2: # cat ifcfg-eno2 TYPE=Ethernet PROXY_METHOD=none BROWSER_ONLY=no BOOTPROTO=none DEFROUTE=yes IPV4_FAILURE_FATAL=yes IPV6INIT=no IPV6_AUTOCONF=yes IPV6_DEFROUTE=yes

Dear Simon, > And can you diff the config of eno1 and eno4. # pwd /etc/sysconfig/network-scripts # diff -u ifcfg-eno1 ifcfg-eno4 --- ifcfg-eno1??? 2020-09-21 17:23:25.576672703 +0200 +++ ifcfg-eno4??? 2020-09-22 07:18:43.160532532 +0200 @@ -3,15 +3,20 @@ ?BROWSER_ONLY=no ?BOOTPROTO=none ?DEFROUTE=no -IPV4_FAILURE_FATAL=yes -IPV6INIT=no -IPV6_AUTOCONF=no +IPV4_FAILURE_FATAL=no

I want to seriously work with IPv6 and not have stray IPv4 functions messing with me. So in /etc/sysconfig/network, I commented out NETWORKING=yes. I have NETWORKING_IPV6=yes. In /etc/sysconfig/network-scripts I altered ifcfg-eth0, setting BOOTPROTO=none. That was enough for eth0 to only have IPv6 working on it (have IPV6INIT=yes and IPV6_AUTOCONF=yes). But lo had IPv4. So I commented

Hello, I'm running a CentOS 5.6 server through linode. I am atempting to configure it for ipv6, previously this had been done though not by me on a ubuntu box so the hardware can take it. I've got an ipv6 tunnel through Hurricane Electric and at a shell prompt have done the following: ifconfig sit0 up ifconfig sit0 inet6 tunnel ::IPV4 Address ifconfig sit1 up ifconfig sit1 inet6 add IPV6

> On 03/09/2015 01:15 AM, Chris Stone wrote: >> >> sysctl -w net.ipv6.conf.all.accept_ra=0 On 03/10/2015 06:52 AM, Robert Moskowitz wrote: > No change after running this and trying both: > > system network restart it's: service network restart Try also setting these in sysctl: net.ipv6.conf.all.disable_ipv6=1 net.ipv6.conf.default.disable_ipv6=1

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 A few months back, I tried to use the network scripts to provision an IPv6 range like can be done with IPv4. I was using CentOS 5.2 at the time and was informed that 5.2 was broken in this regard. I have upgraded to CentOS 5.3 now and I am trying to get IPv6 to provision an entire range of IPs, but I am still getting the old behavior and no IPs are

I want to configure IPV6 on the system and not use some auto ipv6 config. I have tried to use IPV6_AUTOCONF=no in interface script dose not affect anything. ifcfg-eth0: GATEWAY=192.168.1.254 IPV6INIT=no IPV6_AUTOCONF=no BROADCAST=192.168.1.255 BOOTPROTO=none NAME="" NM_CONTROLLED=yes MACADDR="" TYPE=Ethernet DEVICE=eth0 NETMASK=255.255.255.0 MTU="1500"

I just got 50 Mbps symmetric fiber from AT&T and it includes a /56 of IPv6 addresses, replacing a much slower ADSL line. I never tried to get IPv6 working on the old connection. I'm using CentOS 7 as a gateway and it's worked great for several versions for IPv4. I'm not seeing any IPv6 default route on the WAN interface. I suspect I'm not getting route announcements. I

I'm having a problem permanently assigning a static IPv6 address to my CentOS v5.5 box. I have IPv6 enabled and the link local address is automatically brought up. I can manually ifconfig the address but when I configure it in ifcfg-eth0 and restart the network init script the IPv6 address is not assigned. Anyone have any ideas on how to fix this?

Hello, in /etc/sysconfig/network-scripts/ifcfg-eth0 I have this <ifcfg-eth0> ... IPV6INIT=yes IPV6ADDR=prefix::5 IPV6ADDR_SECONDARIES="prefix::2 prefix::3 prefix::4" IPV6_AUTOCONF=no IPV6_DEFAULTGW=prefix::1 IPV6_DEFAULTDEV=eth0 </ifcfg-eth0> when I enter ifconfig the IPv6 addresses are in a different order <ifconfig> eth0 Link encap:Ethernet HWaddr ... inet addr:...

Hi, If I disable ipv6 via the kernel command line, ipv6.disable=1, then systemd-networkd fails to bring up any interfaces. Removing the option and networking works as expected. Phil.

I'm about to publish a fixed IPv6 address and I understand I can use the ip token command to lock the host part of the RA-assigned address to a fixed value. But I can't see an obvious place to configure this. The logical place would be in the ifcfg-<interface> file. Is there someplace else I should set this? NetworkManager? It looks like the new systemd-networkd has support for

Hi all, I'm pretty new to CentOS. I am working with a newly set-up server: [cbearden at host ~]$ lsb_release -a LSB Version: :core-4.0-amd64:core-4.0-noarch:graphics-4.0-amd64:graphics-4.0-noarch:printing-4.0-amd64:printing-4.0-noarch Distributor ID: CentOS Description: CentOS release 6.3 (Final) Release: 6.3 Codename: Final I'm trying to solve this problem (X11 forwarding)

On 10/30/2015 09:01 AM, Timothy Murphy wrote: > Johnny Hughes wrote: > >>> So I guess the strange IP address probably comes from some Lite-On device >>> somewhere in my house - maybe on the server itself, an HP MicroServer. >>> There are so many possible electronic culprits today. > >> You should be able to use nmap to scan the device. > > Thanks