similar to: Linux client for Checkpoint VPN?

Sorry Dag, it is possible to use linux as a roadwarrior client: http://www.fw-1.de/aerasec/ng/vpn-racoon/CP-VPN1-NG-Linux-racoon-roadwarrior.html -------- Original Message -------- Subject: Re: [CentOS] Connecting CentOS to IPSEC VPN (Checkpoint FW1) Date: Mon, 21 Aug 2006 15:20:55 +0200 From: carlopmart <carlopmart at gmail.com> To: CentOS mailing list <centos at centos.org>

Hi, Does anyone have experience using IPSEC on CentOS in order to connect to vendor IPSEC-based VPN products (specifically Checkpoint FW1) ? Is the included IPSEC implementation sufficient, or do people have to rely on OpenSWAN or FreeSWAN ? I'd be testing tomorrow and I'm interested with experiences others have had and things to look out for. Thanks in advance, -- dag wieers, dag

Hello Julius, Thanks - but it doesn't seem to work. I installed sg3_utils and ran #scsi-rescan but that seemed to have done nothing for some reason. Cheers, Boris. On Wed, Nov 4, 2015 at 10:12 AM, Tnjulius <tnjulius at gmail.com> wrote: > Hi Boris, > Just rescan the scsi host. > #scsi-rescan #if you have sg3_utils package > #lsscsi > Or > #echo "- - -"

It should work fine. What esxi version you are using? Eero 4.11.2015 6.27 ip. "Boris Epstein" <borepstein at gmail.com> kirjoitti: > > > > > > > > was the controller you added the virtual disk to an IDE or scsi > controller? > > > > -- > > public gpg key id: 1362BA1A > > > > _______________________________________________

Hi all, If I have a dual-boot machine (Linux and Windows) would I have any good tools under Linux that would allow me to look at the content of the Windows boot partition, administer it, clean up the registry, remove viruses if any, etc? The Windows installation seems to be so defective as to be quite useless so I am trying to think of a good strategy for dealing with the situation. Thanks in

OK, thanks again for all your help. I have resolved this, finally. The problem was that I configured VLAN 48 as the native VLAN on the trunk port.That was a mistake as apparently the native VLAN is the one where Cisco does not bother to tag packets. For now I set the native VLAN to VLAN 1 and that works. Cheers, Boris. On Sun, Jan 25, 2015 at 7:13 PM, Boris Epstein <borepstein at

Anyone know of a client that will allow me to connect a laptop running 4.3 to a checkpoint firewall running an ipsec tunnel? Once i have this working i can say farewell to windows. thanks

On Wed, Nov 4, 2015 at 10:22 AM, Boris Epstein <borepstein at gmail.com> wrote: > Hello Julius, > > Thanks - but it doesn't seem to work. > > I installed sg3_utils and ran > #scsi-rescan > > but that seemed to have done nothing for some reason. > Dumb question: did dmesg even bother to notice *something* was attached? > Cheers, > > Boris. >

Lucian, So far here is the best we could find out: https://bugzilla.redhat.com/show_bug.cgi?id=1084747 Testing to see if this is the solution; so far it seems to be. Cheers, Boris. On Tue, Jan 13, 2015 at 2:49 PM, Nux! <nux at li.nux.ro> wrote: > Use BIND. How the times have changed. :-) > > PS: I'm also curious for a solution.. for when djbnostalgia hits me. > >

Hello all, If I were looking for a load balancer to run on a Linux - specifically, CentOS - machine - what would you recommend? Thanks. Boris.

Less, You are 100% right. Of course I brought up my eth0 - but, like you said, with no IP. Meanwhile, I brought up eth0.48 with 192.168.48.100. However, until I would bring up eth0 with an IP address (any in the network) I would have no connection. Why? That's what I fail to understand. Boris. On Fri, Jan 23, 2015 at 6:45 PM, Les Mikesell <lesmikesell at gmail.com> wrote: > On

Is there a cisco vpn client for linux centso 5 AMD 64 bit? Using google it talks about cisco vpn client but everyplace to download is blocked. I then found a vpnc reference but did not find a 64 bit version. yum install vpnc did nothing.... What is my next step? Jerry

Hello all, Is there a way to recognize a hot-plugged disk (i.e., to get the system to recognize it and build the appropriate /dev/sd* device for the new device) without a reboot? Thanks. Boris.

Thanks for getting back with the "solution". You might want to give that bugzilla entry a jolt, it's been stagnating since last year. :-) Lucian -- Sent from the Delta quadrant using Borg technology! Nux! www.nux.ro ----- Original Message ----- > From: "Boris Epstein" <borepstein at gmail.com> > To: "CentOS mailing list" <centos at

My manual patching of the rejects in checkpoint.c didn''t work out; a delete of 10,000 files caused a panic (in any ext fs, not just Lustre). In the new checkpoint.c, two routines expected by the patch no longer exist: __cleanup_transaction and __flush_buffer. I can avoid the panic if I omit (don''t try to manually patch) the following: Index: linux-2.6.9/fs/jbd/checkpoint.c

Thank you everyone. OK, the mystery deepens, I guess. The machine does need to support several VLAN's, it is currently on a trunkport (8021q encapsulated), it made it into the ARP table - which I specifically tested for by physically unplugging the table, clearing the ARP table and plugging it back in. The ARP table currently looks like this: hq#show arp Protocol Address Age (min)

Hi all, I would be nice if we could find a reliable versioning file system to use as an underlying revision control mechanism. Going by this http://en.wikipedia.org/wiki/Versioning_file_system there aren't all that many options but I am still hopeful. We would most likely be hosting it on a CentOS machine. If you have a perspective on this please share it. Thanks. Boris.

Hi all, Does anybody know of an editor that can do on Linux what Acrobat / Acrobat Pro can do on Mac/Windows? I have tried to use the PDF Import extension to the Open Office which appears barely functional - at least it is so slow as to be almost impractical. I have also tried pdfedit under Linux which seems to work fine but seems to have rather limited functionality. For instance, the capability

On 11/04/2015 10:27 AM, Mauricio Tavares wrote: > On Wed, Nov 4, 2015 at 10:22 AM, Boris Epstein <borepstein at gmail.com> wrote: >> Hello Julius, >> >> Thanks - but it doesn't seem to work. >> >> I installed sg3_utils and ran >> #scsi-rescan >> >> but that seemed to have done nothing for some reason. >> > Dumb question:

Hello, I hope we have the right mailing list. We are two of a team of developers for DMTCP (transparent checkpoint-restart). It runs under Linux, and is free software (LGPLv3+), found at: http://dmtcp.sourceforge.net In our latest release, version 1.2.3, we have done some simple testing on R, and find that we can successfully checkpoint and restart. Its usage can be as simple as: