similar to: DomU Guests not shutting down nicely when Dom0 Hypervisor shuts down

Dear All I am using Centos 7 with Xen 4.6 on a Dell Poweredge T430 When the machine boots, after the 'Scrubbing Free RAM' message, I get a screen filled with little white squares until the login prompt, so I cannot see what is happening as the machine boots. Also there is nothing on the screen when I reboot. My /etc/default/grub is GRUB_DISTRIBUTOR="$(sed 's, release

Yes I usually work headless, but I have been setting it up from new, so need to see what is going on. Regards Francis From: "Scot P. Floess" <sfloess at nc.rr.com> To: "Francis Greaves" <francis at choughs.net> Cc: "centos-virt" <centos-virt at centos.org> Sent: Monday, 22 February, 2016 17:02:12 Subject: Re: [CentOS-virt] Garbled screen

I am running Xen 4.6 on CentOS 7 in a Dell Poweredge T430 I need PCI Passthrough to get USB working. I am following the Xenproject Wiki I have enabled the Virtulasation in the BIOS. I have xen_pciback as a module I have issued the command: xl pci-assignable-add 00:1a0.0 and it shows up fine when I issue this xl pci-assignable-list I have pci=['00:1a.0'] on the DomU config file I

Further to my last post, I have removed the xen-pciback module from the Dom0 kernel, and reloaded it as modprobe xen-pciback passthrough=1 I now have the PCI device on the DomU matching the Dom0 Device usb usb1: SerialNumber: 0000:00:1a.0 instead of 0000:00:00.0 However I now have this error ehci_hcd 0000:00:1a.0: Unlink after no-IRQ? Controller is probably using the wrong IRQ. does

Try this: systemctl start xendomains.service systemctl enable xendomains.service On 21 January 2016 at 08:48, Francis Greaves <francis at choughs.net> wrote: > I am using Xen 4.6.0-8.el7 on CentOS 7 with 3 Linux DomUs. I did have Xen > 4.? on CentOS 6.5 on my previous system. I installed using yum install > centos-release-xen. > On shutting down the Hypervisor it used to

(1) This made no difference. It still hangs around the same place. (2) It wasn't enabled in the kernel so i enabled it. I then rebooted but unfortunately it made no difference. If you want access to a hypervisor to have a play around, let me know. The only information i really have is that if i installed CentOS 7.3 on this hypervisor it works fine. On 11 December 2017 at 16:24, Richard

On 01/19/2016 03:27 PM, Phill Bandelow wrote: > I presume this addresses CVE-2016-0728? > Actually it does not .. they have not rolled that patch into the LTS 3.18 branch at kernel.org yet. As soon as it hits the LTS tree I will build a new kernel though. -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature

There is a new xen kernel for centos-6 and centos-7 the needs testing in: http://cbs.centos.org/repos/virt6-xen-common-testing/x86_64/os/Packages/ and http://cbs.centos.org/repos/virt7-xen-common-testing/x86_64/os/Packages/ Thanks, Johnny Hughes -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 198 bytes

Hi Francis. Personally I would gracefully shutdown all the VM?s first, before attempting to shutdown the xen hypervisor. Are you getting any fsck errors when restarting those VM?s? Kind Regards, Keith On 21 Jan 2016, at 08:48, Francis Greaves <francis at choughs.net> wrote: > I am using Xen 4.6.0-8.el7 on CentOS 7 with 3 Linux DomUs. I did have Xen 4.? on CentOS 6.5 on my previous

Dear George, Thanks for the input and ideas. Unfortunately bootscrub=false dos not work, not does setting nothing for vga, still get the 'Little white squares'! I am asking the xen-users as you suggest Regards, Francis From: "George Dunlap" <dunlapg at umich.edu> To: "Francis Greaves" <francis at choughs.net>, "centos-virt" <centos-virt

Dear George please find attached the three files as requested. I have used iommu=soft in the grub command line for the kernel in the domU as explained before. many thanks Francis From: "George Dunlap" <dunlapg at umich.edu> To: "francis" <francis at choughs.net>, "centos-virt" <centos-virt at centos.org> Sent: Monday, 16 May, 2016 10:29:09

On Thu, Jan 21, 2016 at 1:28 PM, Phill Bandelow <phill at onapp.com> wrote: > Well when the last upgrade 4.2 > 4.4 went live and XM was disabled by > default it took many hosts down without warning. 4.4 > 4.6 may cause the > same issues. It's a dangerous upgrade for sure. Why can't 4.4 be LTS for C6? > as it's the last build with XM. Any XSA patches should not

HI, We've started to see several issues with the Xen releases. Going back to basics I've used this guide https://wiki.centos.org/HowTos/Xen/Xen4QuickStart Once the install process is complete the grub.conf looks like this: default=0 timeout=5 splashimage=(hd0,0)/boot/grub/splash.xpm.gz hiddenmenu title CentOS (3.18.21-17.el6.x86_64) root (hd0,0) kernel /boot/xen.gz

>On Mon, May 16, 2016 at 12:00 PM, Francis Greaves <francis at choughs.net> wrote: >> Dear George please find attached the three files as requested. >> I have used >> >> iommu=soft >> >> in the grub command line for the kernel in the domU as explained before. >> many thanks >The options are: >1. Figure out what the other device is and

Further to my messages back in May I have at last got round to trying to get my DomU to recognise USB devices. I am using Xen 4.6 with CentOS kernel 3.18.34-20.el7.x86_64. I have to manually make the port available before creating the DomU by issuing the command: xl pci-assignable-add 00:1a.0 otherwise nothing shows in: xl pci-assignable-list I have added this to my .cfg file as per the

?My .02 is to stay the course. ?As a server admin, I want to be able to type things like: yum upgrade php ????not yum upgrade php55-epel-rpmforge-fancy-package Having to remember all the idiosyncrasies of a system is what causes some type of major failure in the future whenever (1) you forget something or (2) someone else has to pick up the box to adminster. -- ?Craig Thompson,

> > working in 4.6 for some people, but is working in 4.5 > > How can I downgrade to Xen 4.5 so I can test this out? > > Many thanks > > We do not provide a CentOS-7 version of Xen lower than 4.6. At the > time > we started Xen support on CentOS-7, 4.6 was already stable and that > was > our first release for CentOS-7. > > We do currently have both

We?ve been seeing this a lot lately on generic CentOS 6 rpm installs: rpm -qa | grep libguestfs libguestfs-java-1.16.19-1.el6.x86_64 libguestfs-java-devel-1.16.19-1.el6.x86_64 libguestfs-1.16.19-1.el6.x86_64 libguestfs-tools-1.16.19-1.el6.x86_64 libguestfs-javadoc-1.16.19-1.el6.x86_64 libguestfs-devel-1.16.19-1.el6.x86_64 libguestfs-tools-c-1.16.19-1.el6.x86_64

Francis, I just rebooted my Precision 470 and watched...nothing :( I see the boot menu, and then everything goes blank - as in just a blinking cursor until I get the login prompt. No idea what it's doing - but I don't even see the scrubbing free memory output... On Mon, 22 Feb 2016, Francis Greaves wrote: > Yes I usually work headless, but I have been setting it up from new, so

From: "Francis Greaves" <francis at choughs.net> To: "Francis Greaves" <francis at choughs.net>, "centos-virt" <centos-virt at centos.org> Sent: Sunday, 3 July, 2016 11:19:49 Subject: Re: [CentOS-virt] PCI Passthrough not working Further to my last post, I have removed the xen-pciback module from the Dom0 kernel, and reloaded it as modprobe