similar to: Trouble passing PCI device in isolated IOMMU group

On 07/27/2018 11:51 AM, Quincy Wofford wrote: > I'm attempting PCI-passthrough from host to guest on an HP ProLiant > 380P, which has an outdated BIOS (2014), but it does support VT-d. I'm > running CentOS 7, kernel 3.10.0-862.9.1.el7.x86_64. > > I have an Intel 82580 NIC installed with 4 ports. Each of these ports is > in its own IOMMU group (I enabled SR-IOV at the

Hello, I've tried over at IRC and it appears the solution to this problem may not be obvious. I'm working with a Centos7 box on HP ProLiant 380p hardware. The BIOS is a bit outdated, but both Intel Virtualization Options and VT-d are present and enabled in the firmware. Some relevant command outputs below: -bash-4.2$ dmesg | grep Virtualization [ 1.299295] DMAR: Intel(R)

On Tue, Jul 10, 2018 at 07:47:49AM -0600, Quincy Wofford wrote: > Hello, > > I've tried over at IRC and it appears the solution to this problem may not > be obvious. > > I'm working with a Centos7 box on HP ProLiant 380p hardware. The BIOS is a > bit outdated, but both Intel Virtualization Options and VT-d are present > and enabled in the firmware. > > Some

Hi All; Anyone knows if there is an Asterisk version that setup can be stored in Database instead of the configuration files (.conf)? Any advise? Regards Bilal

Hello Does Samba work in an environment where there are multiple domains with 2-way trusts? Thanks Daniel K. Muturi 1776 Heritage Dr Quincy, MA 02171 Mail Stop: JABS Tel; (617)985-1725

When you create a new rails app the default home page says to rename routes.rb. I tried this, but when I run script/console or script/server I get an error saying the routes.rb file can''t be found. If you rename this file is there an environment variable holding the location elsewhere in the application? -- Posted via http://www.ruby-forum.com/.

Hello Everyone, I have an installation where the client has a Microsoft SQL database that holds all of their case information. They would like the asterisk system to require users to enter a valid case number when making an outgoing call. I?m seeing some documentation regarding people using Microsoft SQL for CDR storage, however nothing regarding validating authentication using a Microsoft SQL

I had my asterisk configuration working very well with broadvoice, but it stopped working this afternoon. I plugged the Cisco 7960 phone I used for my origional signup (just a few days before they offered generic BYOD) and it works fine. I did notice it seems to do all of its comunication through proxy.broadvoice.com (I used tcpdump). I have never contacted broadvoice about using asterisk

I'm trying to get PCI passthrough working by passing through a DVB-T TV card to a VM running MythTV. When I assign the PCI devices in virt-manager and attempt to start the VM I get this error: Error starting domain: internal error: process exited while connecting to monitor: 2015-09-06T12:41:09.725990Z qemu-kvm: -device vfio-pci,host=05:02.0,id=hostdev0,bus=pci.0,addr=0x9: vfio: error, group

I''ve got qualcomm''s qpopper2.2, and am not sure if its vulnerable. The advisory mentions pop and imap servers, but only says: version of IMAP (Section B). If your POP server is based on the University of Washington IMAP server code, you should also upgrade to the latest version of IMAP. Until you can take one of these actions, I installed the new imapd about 3

There is a new updated kernel for centos 3.1 that fixes a security issue. As I have not had time to test this build I am releasing it for testing for 24 hours to pick up any problems before general release. It is available at :- http://caos2.caosity.org:/centos/3.1/updates/i386/RPMS/ The version is 2.4.21-15.0.2.el.c0 Please install and test these packages, they are as yet unsigned and not

I hope someone can enlighten me. I have a quad-port Intel 82580 nic (igb driver) on my system and I''d like to dedicate each nic to a HVM via VT-d PCI passthrough. The IOMMU on my system seems to work, I can assign the PCI devices to my HVMs. The HVMs see the pci device and load their respective igb drivers, and ethtool -i eth0 works on each HVM, shows the drivers are loaded and the

Hello list, I am doing some work for a non profit group. As part of this, I am going to be putting in a 30 handset Asterisk solution. We are trying to keep the costs down as much as possible, as this job includes cabling, I am looking at POE solutions. On the switch side, I am considering something like some Netgear ProSafe FS726TP 24 port switches, or maybe the equivalent Linksys SRW224MP 24

On Thu, May 14, 2020 at 01:22:37PM +0530, Bharat Bhushan wrote: > Different endpoint can support different page size, probe > endpoint if it supports specific page size otherwise use > global page sizes. > > Device attached to domain should support a minimum of > domain supported page sizes. If device supports more > than domain supported page sizes then device is limited

On Thu, May 14, 2020 at 01:22:37PM +0530, Bharat Bhushan wrote: > Different endpoint can support different page size, probe > endpoint if it supports specific page size otherwise use > global page sizes. > > Device attached to domain should support a minimum of > domain supported page sizes. If device supports more > than domain supported page sizes then device is limited

Hello. I've been tesing VGA passthrough using libvirt. However, My *Windows7*(64bit) Virtual Machine stopped at loading screen as soon as I installed graphic driver(*AMD Radeon HD 7750*) and then restarted the VM. How Can I use VGA passthrough technology in my *Windows7* VM? I attached my testing information(HW, system environment and settings, qemu log and so on..) Best Regards.

Hi all I have a very weird case of pci passthrough. I have a machine with 7 network interfaces, all of them intel. Four of them are on one quad giga ethernet device. If I manually unbind the devices and allow qemu to use them, with intel IOMMU working, everything works like a charm. Here's how I do it manually: root@kybrat (x86_64) ~]$ lspci -nn | grep net 00:19.0 Ethernet controller

How can it be, that class 1:3 in my case borrows, when all sibling classes are isolated ? nessus:~# tc -s -d class show dev eth1 class cbq 1: root rate 100Mbit cell 8b (bounded,isolated) prio no-transmit/8 weight 100Mbit allot 1514b level 2 ewma 5 avpkt 1000b maxidle 1us Sent 484 bytes 7 pkts (dropped 0, overlimits 0) borrowed 0 overactions 0 avgidle 77 undertime 0 class cbq 1:1 parent 1:

Hi! I am trying to get this scenario working: http://lists.xensource.com/archives/html/xen-users/2005-07/msg00558.html - Dom0 as well as the DomU firewall are Gentoo systems with Xen 3.0.2. - Both physical nics are hidden from Dom0 and are already working in the DomU firewall - A bridge exists in the DomU firewall (i don''t know if this is correct). That is for the DMZ to connect other

Hi, I try to configure a kvm with a NIC, but no attached network to this NIC. I tried following methods: 1. Create a generic ethernet connection I configured the VM with following interface section: <interface type='ethernet'> <script path='/root/noscript.sh'/> <target dev='myvm_nic0'/> <interface/> The script /root/noscript.sh