similar to: <source mode='private'> for PPPoE?

Hello, CentOS 8 dropped the rp-pppoe package. My attempts with NetworkManager-ppp already failed because it seems that it is not possible to use a VLAN as a device. Please, how does it work under C8 to set up a pppoe connection (German Telekom, VDSL (VLAN 7 required), ZTE modem). Thanks. Joe

AHOI! I've big trouble by setting up CentOS 6.3 for my new vDSL. As I've found out, the German Telekom is using VLAN7 for her internet-(data) connections. => http://workaround.org/blog/vdsl O.K. what I've done: The NIC where's my DSL-modem is connectet is eth0. cat /etc/sysconfig/network-scripts/ifcfg-eth0 # device for vDSL-modem DEVICE=eth0 HWADDR=00:30:1B:14:08:67

I am a newbie to linux and shorewall. I am reading the shoreall quickstart guides. I am a bit confused about the following statement: ----------- quote -------------- The firewall has two network interfaces. Where Internet connectivity is through a cable or DSL "Modem", the External Interface will be the ethernet adapter that is connected to that "Modem" (e.g., eth0) unless you

HI guys i need help i install centos 4.1 and apt-get the rp-pppoe. so i setup the rp-pppoe using adsl-setup and input all the data given by the provider. When i connect to my dsl using adsl-start it keeps on terminating where can i find the logs for rp-pppoe and anyone had this kind experience with bellsouth adsl? anyway when i connect the modem to my linksys wrt54g router it worked fine. --

I am having a little trouble getting my head around this so any help would be appreciated. I have just signed up a new service and have been allocated the following subnet which gives me 30 usable IP addresses. 210.15.xxx.192/27 The connection is made via pppoe which works fine and the connection creates ppp0 and assigns 210.15.xxx.193. Now I want to use 4 IP''s in a DMZ and the reset

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello, I''m using HTB to shape my outgoing traffic over a ADSL-link with PPPoE with a nominal bandwidth of 128kbit/s. My goal is to favour small packets like ACKs and interactive services like ssh; in other words, I want to achieve low lantency. If there are some big packets going over the wire, everything works fine. But if there are

I am building a CentOS 5 box to ship to Houston which will be a gateway system on an SBC DSL connection for a while until the client gets a T1 installed. I have read up on using adsl-setup and related software, but never done PPPoE on anything but LinkSys commodity boxes. I have examined the adsl-setup script, and I think I understand how this works, but want to be sure I understand things

My provider is getting ready to switch my DSL router to bridging mode and I supply the router (so I can get no only IPv4 addresses but also IPv6 addresses!). Here are his 'instructions' to me: "Basically you start pppoe, I give you the username and password for it, and then I set the router to passthrough modem mode, and you initiate the PPPoE session directly with my LNS back

I have three ADSL lines that I''d like to use as one big pipe to the internet. The ADSL service works by establishing a pppoe connection (the ADSL "modem" is a bridge), and each pppoe interface gets its own IP address. This means I''d have to have 4 ethernet interfaces (3 for each of the ADSL modems and 1 for the LAN) in my gateway. I''d setup the gateway to NAT

Dear all, I just stumbled over the following instruction in the LLVM IR of a C program compiled with clang: %26 = call i32 (...)* bitcast (i32 (i32, i32, i32, i32, i32)* @KeWaitForSingleObject to i32 (...)*)(i32 %23, i32 %24, i32 %25, i32 0, i32 0) Since our LLVM Parser choked on this instruction, I tried to check the documentation, but did not find anything about such nested bitcasts within

I need basic PPPoE startup help. adsl-start DID bring up my PPPoE link (ppp0) to my ISP over eth0 via the DSL modem/bridge. My IPv4 CIDR block is routing and Shorewall is doing the firewalling. But shorewall has to be started after ppp0 is up and working. For now this means running shorewall restart (or start?). Shorewall 4.2 will have a way to restart shorewall without recompiling, I

On Sat, 2 Mar 2019 10:25:49 +0100 Michael Ströder <michael at stroeder.com> wrote: > On 3/1/19 10:17 PM, Rowland Penny via samba wrote: > > You don't need to precreate the computer, the join with 'net' will > > do it for you. > > But then I need to have administrative rights on the OU for the admin > doing the actual join. For security reasons I

Peter Jakobi wrote: > Hi Jiri, > > you already tested an ancient userspace-only rp-pppoe? > I''ve still one active, and trying this you could validate > your the rest of your setup, before looking at possible > kernel changes anew (strace, ltrace, logs, whatever)... > Hi Peter. No I did not. Do I have to compile it? Can you give me more info what to do?

Hi all, I am trying to install the PPPoe server rp-pppoe-3.8 from Roaring penguin on centos PC (Centos 4.3, Kernel release 2.6.9-34.EL) but not able to start it. When I start it it gives the error-- /etc/rc.d/init.d/pppoe status pppoe-status: Link is down (can't read pppd PID file /var/run/pppoe.conf-pppoe.pid.pppd) ror - /etc/rc.d/init.d/pppoe start Bringing up PPPoE

Hello to everyone, Can someone help me with hints on how to configure a pppoe gateway on a linux box with 200+ clients behind it ? I''ve read that user-space daemons give A LOT of CPU overhead. I''m opened to ANY solution ! -- Radu Cugut mobile: +40 742 045686 web: http://rcugut.has.it

Hi, I want a way to traffic shape pppoe encapsulated pkts based on its src/dst Ip address. Is there any way I can mark pppoe encapsulated pkts? Samit

Hello, My system is: Server with Slackware 8.1 LINUX, ADSL Internet with PPPoE connection, and I masquerade my LAN. I use "Roaring Penguin" PPPoE client for my ADSL connection. I would like to connect another ADSL line (also PPPoE) to my server and have two lines, because I want to make "Simple source policy routing", as described in LARTC HOWTO. How should I set up my

Dear all, Though this is not LARTC related question, finding no other help I am forwarding this question for this group. Hope some GURUZ will help me. I want to authenticate my lan users through pppOE. I am using rh 9.0 box as my gateway. How / Which software do i use on my linux box to provide pppOE service and in client end win98/2000/Xp which software do i use?

I was given the challenge recently of creating a LAN-LAN bridge between two buildings several hundred metres from each other, using only existing Cat 3 wiring and without having to resort to an expensive and finicky 5 Ghz wireless link. I was able to create a 90 megabit link for about $3,000 Cdn with new PC's, CentOS 4.1, and the newly avaliable Black Box VDSL Ethernet Extender, which

Hi BKF, you can configure icecast to serve thousands of listeners but it's not going to happen on anything less then an industrial strength internet connection. If you have ADSL you can probably handle 5 listeners maybe 10 on an average service. If you have VDSL increase that to 15 maybe. If you have fibre it might do 25. It all depends on the service provided by your ISP and the