similar to: libvirt equivalent for VMWare for SCSI mode = independent-persistent?

I have Centos 5.2 and am trying to set up my first tape loader, a Quantum SuperLoader 3. My "cat /proc/scsi/scsi" outputs the following: Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: transtec Model: PV610F16R1C Rev: 373I Type: Direct-Access ANSI SCSI revision: 05 Host: scsi1 Channel: 00 Id: 01 Lun: 00 Vendor: HP Model: Ultrium

Hi people, I installed a via SATA controller in a CentOS release 3.8 (Final) - I needed additional disk space. After the first boot, the kudzu service, added the following line to /etc/modules.conf: alias scsi_hostadapter sata_via and I rebooted. After reboot in dmesg one can see: scsi0 : sata_via scsi1 : sata_via Vendor: ATA Model: SAMSUNG HD080HJ Rev: WT10 Type: Direct-Access

https://bugzilla.redhat.com/show_bug.cgi?id=1441197

Okay, this is probably a stupid question, but here goes: We've got a database server that I'm going to wipe clean and install the latest OS. It's running 2.1 right now, and it has a hardware raid. I've found lots of stuff on software raid tools, but are there any tools on hardware raid? We've got another box, an IBM AS/400, and when one of it's raid disks fail

Hi! Report from my multipath tests today. My test virtual machine, that runs from an NPIV pool, is not able to use multipath. When I pulled the cable from one of the targets, it crashed. But, strangely, it could boot up again on that other path, that it just crashed on. That tells me it can use both paths, and is not limited to one of them only, but because the multipath layer isn't

I'm having speed problems with the SCSI card we're using to do tape backup. It seems to be functioning in 16 bit mode and the current thinking is that perhaps it's using a legacy driver instead of the correct one. The Adaptec site has a 'driver' for RHEL5 which I've downloaded and tried to install but it seems to have a problem installing on a CentOS-5 system. [root at

I've been having no end of issues with a 3ware 9650SE-24M8 in a server that's coming on a year old. I've got 24 WDC WD5001ABYS drives (500GB) hooked to it, running as a single RAID6 w/ a hot spare. These issues boil down to the card periodically throwing errors like the following: sd 1:0:0:0: WARNING: (0x06:0x002C): Command (0x8a) timed out, resetting card. Usually when this

Basically the issue comes down to my Volume Groups not being found by this initrd, causing good ole kernel panic. initrd-2.6.12.6-xen3_12.1_rhel4.1.img [root@xen01 lvm]# uname -a Linux xen01.inside.***.com 2.6.9-22.0.2.ELsmp #1 SMP Thu Jan 5 17:13:01 EST 2006 i686 i686 i386 GNU/Linux [root@xen01 lvm]# cat /etc/redhat-release Red Hat Enterprise Linux ES release 4 (Nahant Update 2) Everything

Hi, Is there something OS related (CentOS 5.1) I would need to do for a CLI created array to become visible to the OS after the array is created and initialized? I don't want to reboot... Thanks! jlc -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.centos.org/pipermail/centos/attachments/20080201/ed076445/attachment-0001.html>

Hi again! Need to add here, since I been investigating a bit further, that it seems to be possible to add an NPIV vhba to the guest, using vdsm hooks. I've seen the reference to "host device assignments", which Dan pointed me too, but I didn't really understand the meaning of it at that moment. It would be interesting to hear from someone that have been doing it, how it would

Hi people, I ran into one of these silly issues I'd like to share as I think the reason behind it may be a flaw in the current initrds. The setup; Dual-Xeon Intel-chipset motherboard. SATA-disk attached to ICH, onboard Adaptec SCSI-controller. Installed system, updated packages, no problems. Basic, non-LVM partition setup - OS-disk is /dev/sda, single filesystem-partition /dev/sda1 is

Samba mount (from one of our build scripts). We decided to upgrade to RedHat 7.2 (which uses a newer version of Samba -- 2.1.1b IIRC), maybe that fixes the problem. However, I decided to submit this bug report, in the hope that it may help kill some bugs. (Remember -- the only good bug, is a dead bug :)) So, here is the dmesg output: Linux version 2.2.16-22enterprise

hi all We have a rh linux server connected to two HP SAN controllers, one an HSV200 (on the way out), the other an HSV400 (on the way in). (Via a Qlogic HBA). /etc/multipath.conf contains this : device { vendor "(COMPAQ|HP)" product "HSV1[01]1|HSV2[01]0|HSV300|HSV4[05]0" getuid_callout "/sbin/scsi_id -g -u -s /block/%n"

I've been having an extremely hard time using the on board SATA controller on my nvidia based board. I have two 160gig Maxtor SATA drives attached to the on board controller, setup as software raid0. The problem is the array is extremely unreliable, where I'm getting constant I/O errors like: sd 0:0:0:0: SCSI error: return code = 0x00040000 end_request: I/O error, dev sda, sector

Hi folks, I inherited a very old computer (I guess about 8 years old) which I'd like to use for some training on CentOS. I downloaded images for CentOS 6.4 i386 (DVD 1 and 2) and burned them onto discs. After inserting DVD 1 into drive and booting, on the "Welcome to CentOS 6.4!" screen I select "Install or upgrade an existing system". I then skip the media test and

I really hope someone has a clue on this one.... :) I've got a 2.2TB array mounted on a 3ware 9500 controller. I installed it last week ensuring that LBA was enabled and using gpt with parted to get the full size available on one array. I also think I chose reiserfs for the array. We then moved ALOT of data to the array. Problem now is that after a reboot LBA doesn't seem to be in

I have an IDE based PC running Linux/CentOS4 to which I wish to attach a scsi dlt. The host controller is an Adaptec AHA3940 something that lspci reports as: SCSI storage controller: Initio Corporation 360P (rev 02). I would like to have the system load the driver for this adapter at boot but I have two problems: 1. I am not sure which driver to use; and 2. I do not know how to force

Hello, After updating to 6.6 I've lost my connection to my tape library. Old log file (6.5): Sep 13 08:17:51 server1 kernel: scsi 1:2:0:0: Sequential-Access HP Ultrium 5-SCSI Z65W PQ: 0 ANSI: 6 Sep 13 08:17:51 server1 kernel: scsi 1:2:0:1: Medium Changer HP 1x8 G2 AUTOLDR 4.20 PQ: 0 ANSI: 5 New log file (6.6): Oct 28 18:15:06 server1 kernel: scsi1 : hpsa Oct 28 18:15:06

http://libvirt.org/formatdomain.html#elementsHostDevSubsys At this description used "drive"-typed address for SCSI. But when i get xml-description of scsi-devices by <code> unsigned int flags = VIR_CONNECT_LIST_NODE_DEVICES_CAP_SCSI_HOST ; int ret = virConnectListAllNodeDevices (currWorkConnect, &nodeDevices, flags); then get by

Hi all, I use libvirt-go in my agent to attach rbd volumes. I ofen suffer the issue of incosistent of domain dump xml and domain persistent xml file. For example, when I try to attach volume, the the domain by ?virConnectListAllDomains? api from libvirt tell me the vdf or 0x0a is empty, but when attach it with the vdf device or 0x0a address, qemu return the error duplicated with vdf or PCI