similar to: Error message doesn't make sense

On Fri, Dec 04, 2015 at 10:42:30AM +0800, Tashi Lu wrote: > Hi everyone, > > I incidentally configured two IDE controller for my machine-1.2 VM(it > might be virsh attach-disk to blame), and I got the error message > "Only a single IDE controller is unsupported...". I can't understand > this error message, I think it means I HAVE to configure two or more > IDE

Hi all, I was trying to take live snapshot of VMs, but I got the following error: [root@localhost ~]# virsh snapshot-create-as 1 test desc --live --memspec file=mem.bak,snapshot=external --diskspec vda,snapshot=external,file=/root/root.bak.qcow2 error: Operation not supported: live disk snapshot not supported with this QEMU binary I upgraded my qemu-kvm 0.12.1 to qemu 1.2, the error still

On Fri, May 5, 2017 at 12:52 PM, Nikolaos Milas <nmilas at noa.gr> wrote: > On 5/5/2017 1:42 ??, Nikolaos Milas wrote: > > Hmm, it seems that the boot flag should be removed from /dev/vda2 >> partition? >> > > Actually, I tried this and left the boot flag only to /dev/vda1. I > rebooted and I am still getting the same error. :-( > > I was hoping we were

Hi all, is it possible to monitor guest's interface's stat which uses SR-IOV virtual function? I don't know how qemu/libvirt implement monitoring, if functions like interfaceStats are implemented in the host, I think there's little chance to do this due to SR-IOV's nature, is it right? If i can't use libvirt to monitor SR-IOV interfaces, is there another way to do

Hi, One of the I noticed during migration from XM toolchain to XL in PCI Pass-through was that we used to specify target bdf in HVM guest as pci = [ ''0000:07:11.6=0@1a'' ] However with XL, it now seems like this is the correct syntax: pci = [ ''0000:07:11.6@1a'' ] Is that correct? I''ve verified that it works but what about zero in

On Wed, Jun 5, 2013 at 9:58 PM, upen <upendra.gandhi at gmail.com> wrote: > I copied pxelinux.cfg/default to pxelinux.cfg/<IP to HEX> and it looks this > step resolved the earlier error. Next I get failed to load com32 file > vesamenu.c32 while that file exists in /tftplinux/linux-install. Is vesamenu.c32 from 5.10? -- -Gene

I've installed Syslinux on a somewhat old system. The motherboard is based on an Intel 440GX chipset (specifically it's the Supermicro P6DGE if that means anything.) The harddrive has been split up into partitions of one hidden FAT16 (marked as active) to which syslinux is installed (hda1), one normal FAT32 which has windows and dos (hda2.) It also has an extended partition containing

On 5/5/2017 1:19 ??, Gianluca Cecchi wrote: > Could you verify, if /dev/sda is your boot disk, with the command > > fdisk -l /dev/sda > ? It's /dev/vda in my case: # fdisk -l /dev/vda Disk /dev/vda: 21.5 GB, 21474836480 bytes, 41943040 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512

On Tue, Aug 04, 2015 at 07:11:29AM -0700, Ryan Barry wrote: >On 08/03/2015 10:47 PM, Martin Kletzander wrote: >> On Mon, Aug 03, 2015 at 03:39:30PM -0700, Ryan Barry wrote: >>> On 08/03/2015 01:43 PM, Ryan Barry wrote: >>>> Using: >>>> >>>> edk2.git-0-20150803.b1141.ga0973dc.x86_64 >>>>

On Mon, Aug 03, 2015 at 03:39:30PM -0700, Ryan Barry wrote: >On 08/03/2015 01:43 PM, Ryan Barry wrote: >> Using: >> >> edk2.git-0-20150803.b1141.ga0973dc.x86_64 >> edk2.git-ovmf-x64-0-20150802.b1139.gb234418.noarch >> >> On Fedora 22. >> >> Provisioning a i440FX system in virt-manager and attempting to boot >> results in successful EFI

Just thought I'd pass along that I have successfully installed FreeBSD 7.0 into a Xen 3.1 HVM. ?This one went as smooth as I expected, considering my experience with 6.3. ?Haven't done any benchmarking or stress testing or port installs or anything. ?But so far it's working nicely. Here's all the info. ?If you'd like to see anything else, let me know. Host hardware: ?

Hello, I have a big problem with my servers. I have 4 NIC on all my KVM Servers but the most time on a start (restart) I lost one NIC? It is not always the same, but this two are virtio NICs. with ifup eth0(1) the system say,I have no configured eth0 or eth1 file ? Can any tell me what I can do? thank's for a answer NetworkManager is disabled. -- mit freundlichen Gr??en / best regards,

Using: edk2.git-0-20150803.b1141.ga0973dc.x86_64 edk2.git-ovmf-x64-0-20150802.b1139.gb234418.noarch On Fedora 22. Provisioning a i440FX system in virt-manager and attempting to boot results in successful EFI initialization, but the VM exits ungracefully after the bootloader (with F22 and CentOS 7 installer images). There's no really useful information in any of the logs. Using qemu-kvm

I am working on S5000VSA Intel Server Board with the following cpu spec. XEN-PEER-RHEL5 $ cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 15 model name : Intel(R) Xeon(R) CPU E5345 @ 2.33GHz stepping : 7 cpu MHz : 2327.512 cache size : 4096 KB physical id : 0 siblings : 1 core id : 0

On Thu, Jun 6, 2013 at 3:48 PM, upen <upendra.gandhi at gmail.com> wrote: > > > > On Thu, Jun 6, 2013 at 1:01 PM, Gene Cumm <gene.cumm at gmail.com> wrote: >> >> On Thu, Jun 6, 2013 at 11:58 AM, upen <upendra.gandhi at gmail.com> wrote: >> >> >> This is sounding like dropped/intercepted packets. Could we get some >> >>

Hi, I''m working with Xen 3.0.1 and I have the following problem: I''m running Xen in a VT enabled Intel processor, I have successful installed a Fedora Core 4 32 bits Guest using VT. But the Network interface doesn''t appear in the Guest. I mean, running the commands "ifconfig –a" doesn''t show any eth0 interface just lo. In the /sys/class/net directory

On 05/05/2017 12:57, Gianluca Cecchi wrote: grub-install /dev/vda2 didn't work ? > On Fri, May 5, 2017 at 12:52 PM, Nikolaos Milas <nmilas at noa.gr> wrote: > >> On 5/5/2017 1:42 ??, Nikolaos Milas wrote: >> >> Hmm, it seems that the boot flag should be removed from /dev/vda2 >>> partition? >>> >> Actually, I tried this and left the boot

On Thu, Jun 6, 2013 at 11:58 AM, upen <upendra.gandhi at gmail.com> wrote: >> This is sounding like dropped/intercepted packets. Could we get some >> details on the client (make/model of computer/motherboard, same for >> NIC, PXE OROM details)? Is it connected to the same physical switch >> as the DHCP/TFTP server? Any chance that the physical switch that the

Sure, I don't mind testing it out on there for you, but, where do I find the pre releases to try then? At least we know it's between 2.13 and 3.00. That narrows it a bit I would think. Mind you, if it jumps up a major revision number, I guess that means a lot of changes went in. On 8/2/05, syslinux-request at zytor.com <syslinux-request at zytor.com> wrote: > Send SYSLINUX

I've got a Digium PCI telephone card that I'm trying to use with an AsteriskNow guest, on a CentOS 5.2 host. I've tried setting up the pciback stuff, and think I've done it right, but the card does not show up in the guest. I'm obviously missing something, so any help (including ways to debug this!) would be greatly appreciated. Here's some more info: The guest is