similar to: ralink rt61 in centos 5

Hello, Maybe someone will run into the same problem, so here is how it works for me. I could not get work my wlan card (ralink rt61) with the driver from rt2x00.serialmonkey.com under CentOS 5 (2.6.18-8.1.1.el5). All drivers (beta and daily cvs) from this site freezes my system. So I get the driver from the Ralink support at http://www.ralinktech.com/ralink/Home/Support/Linux.html

From: Johannes Berg <johannes.berg at intel.com> Declaring the factor is counter-intuitive, and people are prone to using small(-ish) values even when that makes no sense. Change the DECLARE_EWMA() macro to take the fractional precision, in bits, rather than a factor, and update all users. While at it, add some more documentation. Signed-off-by: Johannes Berg <johannes.berg at

From: Johannes Berg <johannes.berg at intel.com> Declaring the factor is counter-intuitive, and people are prone to using small(-ish) values even when that makes no sense. Change the DECLARE_EWMA() macro to take the fractional precision, in bits, rather than a factor, and update all users. While at it, add some more documentation. Signed-off-by: Johannes Berg <johannes.berg at

I know, I know... don't use the non-standard kernels unless you have to... BUT: I have a D-Link N150 USB card. Bus 001 Device 004: ID 0846:9030 NetGear, Inc. WNA1100 Wireless-N 150 [Atheros AR9271] This isn't supported in C5, but it is supported in newer kernels (ath9k_htc). So let's try NDISwrapper: # rpm -i kmod\-ndiswrapper\-1.56\-1.el5.elrepo.i686.rpm

HI I admit up front that I know just enough about wireless networking to know that I don't know much at all about it. That said, I'm hoping someone can help me learn a little bit... Specifically, could a laptop running Centos 5.1 be expected to (be able to) connect to a wireless access point using WPA2 security settings? I don't know if WPA depends on hardware support, or if

I just installed an Asus PCE-n13 wireless card into one of my CentOS 5.6 systems. It uses the RaLink 2680 chip set and I was able to get the driver loaded using modprobe rt2x00pci.ko. I saw no error and now see that the module is loaded along with mac80211 and other dependencies. Now I need to know how to create the wlan0 device. I can find nothing via Google searches on how to create that

Hi everyone, My PC don't have an integrated WLAN card, so I bought an USB WIFI device which use the MediaTek MT7601U chip(image 'dongle.jpg'). ------------------------------------------------------------------------------------------------------ My PC specification- OS = CentOS 7.8.2003. Processor = AMD Ryzen 5 1600. Mother-Board = GA-Gigabyte A320M-S2H

Hello, I am using CentOS 4.6 (2.6.9-67.plus.c4) on a toshiba tecra 8000 notebook. If closing the panel, "Panel Power On/Off" is enabled in bios, the notebook does suspend. But after opening the panel, the notebook completely freezes. If the suspend only takes a few minutes, then everything is working fine. But if the suspend takes a time more than five or ten minutes, the system

Hello, I have installed CentOS 5 (2.6.18-53.1.4.el5) on my new Acer Extensa 5220 notebook and everything seems to work fine except of the following: 1) Display is ok, but could maybe be better? The driver is set to 'vesa' but should be 'intel', in my opinion. But 'intel' isn't working in xorg.conf. 00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960

Hi, My wife and I live in a two-storey flat, and we have a small home LAN (100% CentOS 5) with a "classical" configuration: On the ground floor, there is the telephone jack with the DSL modem router (192.168.1.254). This modem has a mini-switch with two Ethernet jacks to it, and the two are used by: - the server (192.168.1.1), a "black box" running in a cupboard 24/7 -

Hey All, In looking for a solution for the subject wireless on my friend's Asus A54C laptop I found this entry: http://www.centos.org/modules/newbb/viewtopic.php?topic_id=39054&forum=55 rt2860-firmware-26-1.el6.elrepo.noarch.rpm kmod-rt5390sta-2.5.0.3-1.el6.elrepo.x86_64.rpm This solution appears to have worked for the RT3090. Would these be the right rpm's for my friend to

Hello, I am looking for developer(s) to assist with two separate capabilities as contributions back to the community. 1) The ability to send management frames in wifi monitor mode with the run0 driver using the Ralink RT6390. 2) I would also like to get HostAP working with the same Ralink RT6390 radio. WEP, WPA and WPA2 support are required for wifi Access Point mode. Please feel free to

hi all, this is my first hit on the mailing list. hope i m posting in the right place. well, i have a dell vostro 1510 laptop with broadcom wifi adapter. n it doesnt work! :( i installed the wifi drivers with ndiswrapper. iwconfig shows the following. [root at laptop ~]# iwconfig lo no wireless extensions. eth0 no wireless extensions. sit0 no wireless extensions. wlan0

I have a new install of CentOS 6.4 on an HP Pavilion 500-27c with one mother board nic card. results of lspci : 01:00.0 Ethernet controller: Atheros Communications Inc. AR8161 Gigabit Ethernet (rev 10) 04:00.0 Network controller: Ralink corp. Device 539b results of ifconfig -a lo Link encap:Local Loopback wlan0 Link encap:Ethernet HWaddr 70:18:8B:80:AE:71 There is no

I realize that many on this list have likely applauded the NetworkManager package split that removed wireless stuff into its own package, NetworkManager-wifi, because for wired workstations and servers it might be desirable to not have any wifi software installed. And I believe it was a sound technical decision to do the split. However, in doing a fresh installation of what most call CentOS

hi list members, my goal is to make one of my DomU''s act as a wireless accesspoint... So, i need it to have access to the pcmcia wlan card attached to dom0. But how ? when i give the pci=[] option to the domU config file its shows up with lspci but i cant use it... (on debian with module-assistent get rt2x00 in de DomU) Is it possible or would it be better to use a more direct interface

Any hope of getting my laptop's Broadcom BCM94311 wireless running on CentOS 5? I find lots of references to using fwcutter to get the needed firmware from Windows drivers, but there's a Catch-22: Version of fwcutter that generate files for the bcm43xx driver in CentOS 5 don't recognize the md5sum of any currently available Windows driver. Newer versions of fwcutter

I persuaded a reluctant friend to buy a new computer. I enthusiastically extolled the joys and benefits of Centos and promised to install it on his new machine - dual booting with Micro$oft Windoze 7. His super-duper new laptop arrived. Acer, AMD 4 core, fast etc. but not as nice looking as my impressive HP DV5. The wireless refused to connect. After 8 hours on Saturday I could sometimes see

There is a new fallthrough pseudo-keyword macro that can be used to replace the various /* fallthrough */ style comments that are used to indicate a case label code block is intended to fallthrough to the next case label block. See commit 294f69e662d1 ("compiler_attributes.h: Add 'fallthrough' pseudo keyword for switch/case use") These patches are intended to allow clang to

There is a new fallthrough pseudo-keyword macro that can be used to replace the various /* fallthrough */ style comments that are used to indicate a case label code block is intended to fallthrough to the next case label block. See commit 294f69e662d1 ("compiler_attributes.h: Add 'fallthrough' pseudo keyword for switch/case use") These patches are intended to allow clang to