similar to: New UPS to the DB

On Tue, 7 Jul 2020, Alexander Karenin wrote: > Hi, I have an OEM of KStar UDC9101S which is Megatec protocol rs232 capable unit.So I use blazer_ser protocol=megatec /dev/ttyUSB0 with no issue to get > NUT running. > > Please direct me what command should I issue to collect the data in order to include the UPS to device database? It would be interesting to see the output of upsc

Hi, recently I got a GE EP6000R UPS. At first I feared it's not supported at all, but after digging in I found out that it's supported by the 'blazer' driver. The UPS has both RS232 and USB connection. To use the RS232 connection, I had to use the 'cablepower = none' as the UPS is using only RX, TX and GND pins. So my 'usp.conf' was a bit like that: > [myups]

Hi, I've got an AEC Star T4110 connected with an RS232 port by a megatec cable. On the list of supported devices (http://www.networkupstools.org/stable-hcl.html) there is only one AEC device, so I tried genericups with upstype=21. The problem is, that the UPS (while being on-line) reports constantly being on battery. # upsc aec ups.status OB My question is: What is the recommended procedure

>I wonder how difficult it would be to rip off their modifications and revert to a.standard, functional nut. I think it should be preatty simple. just rename Synology files and replacewith what you think is the best there... it's just a banch of scripts nothing more...

Hi all, I am quite new to nut mail list and not good in English. My OS is Armbian 23.02.2 Jammy with linux 5.15.93-sunxi Hardware is Raspberry pi Nut version 2.7.4-14ubuntu Install via apt-get install UPS manufacturer : Kstar Model : micropower Cannot find the manufacturer on the HCL Kstar is a oem manufacturer. That OEM to many brand. Lsusb show : Bus 006 Device 004: ID 09d6:0001 KSTAR UPS

Hello, Replaced UPS Kstar Micropower Micro 1200 (managed via blazer_usb) with https://www.njoy.ro/UPS/horus-plus-2000. The latter doesn't seem to be supported. 1. I tried blazer_usb and usbhid-ups. Any other suggestions? 2. What would be needed to get it supported by NUT? ======== HW ======== HP Microserver Gen 8 ======== UPS ======== Working:Kstar Micropower Micro

Hi, I have a bunch of UPSs, most connected to pcs with Linux working 100% with NUT. The only one I have a problem with, is connected to Windows 7 64bit, and I used the straight MSI installed from the website named NUT-Installer-2.6.5-4.msi Took me a while to find a way to get it to work, but it is ugly for now. Just starting up the service results in a NUT not working at all, and I tracked it

Hello list, we've got a PowerWalker VI 1000E/RT LCD UPS and like to use it with NUT using the blazer_ser driver. For the blazer_ser driver to display percentage, one has to add battery.voltage.high and battery.voltage.low voltages to the ups config. Here's what I received from the powerwalker customer service: Battery-Low Voltage: 21.6VDC Battery Shutdown: 19.2VDC Now my questions: 1.

Manufacturer: Aviem Power RT 1000-3000VA Description: Rack/Tower Intelligent Online LCD UPS. connected with serial cable. #upsc battery.voltage: 24.96 battery.voltage.low: 21.5 battery.voltage.nominal: 24.0 beeper.status: enabled device.mfr: device.model: device.type: ups driver.name: blazer_ser driver.parameter.pollinterval: 2 driver.parameter.port: /dev/ttyUSB1 driver.version: 2.6.3

Hi Users NUT, I want monitor a UPS of brand SMS (Sinus Double 8 KVA) using a raspberry-pi. In compatibility list, is listed to use the blazer_ser driver. I use a USB adapter to RS-232 conected in to the No-Breake. Follow the comands e confs. root at rasp:/home/pi# lsusb *Bus 001 Device 004: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port* Bus 001 Device 003: ID 0424:ec00 Standard

Hi Artronic art 1000 bl is supported partially by blazer_ser: battery.voltage: 13.40battery.voltage.nominal: 12.0 beeper.status: enabled device.type: ups driver.name: blazer_ser driver.parameter.pollinterval: 2 driver.parameter.port: /dev/ttyS0 driver.version: 2.6.3 driver.version.internal: 1.51 input.current.nominal: 4.0 input.frequency: 50.1 input.frequency.nominal: 50 input.voltage: 232.9

Barry, I have had success with NUT on Debian and an EATON 5E2000IUSB-AU 5E 2000VA/1200W UPS With 3 x OUTLETS which I believe is good value. I would believe the the EATON ?5E 1500VA/900W UPS With 3 x OUTLETS would work just as well. The 1500VA also uses the same batteries as the 2000VA so I would believe it would run its raited load longer than 2000VA. My eight drive RAID driver uses less that

Hello, I have been following the details in this article to configure my UPS: http://rogerprice.org/NUT.html However the system won't shutdown although file permissions look ok: ls -alF /usr/sbin/ups* -rwxr--r-- 1 upsd daemon 64984 Oct 15 2014 /usr/sbin/upsd* -rwxr--r-- 1 upsd daemon 48584 Oct 15 2014 /usr/sbin/upsmon* -rwxr--r-- 1 upsd daemon 31536 Oct 15 2014 /usr/sbin/upssched*

I have a Dell PE 2850 connected via 940-0024C cable to serial port on the UPS mentioned above. I've used apt-get to install nut-2.0.2-3 and attempted to configure based on the documentation. So far I'm getting the following when I try to start ups daemon: server:/etc/ups # /etc/init.d/ups start Starting service NUT: -> Starting UPS driver: Network UPS Tools - UPS driver controller

On Wed, 14 Oct 2015, Davide Baldini wrote: > upsdrvctl shutdown > ... > instcmd(shutdown.return, [NULL]) > instcmd: FAILED > Shutdown failed! > Driver failed to start (exit status=1) > > This time /var/log/syslog doesn't register anything about the UPS after > issuing the command above. Instead, It logged some errors after a > upscmd -u admin -p mypass

Hi Charles, >----- Original Message ----- >From: "Charles Lepple" <clepple at gmail.com> >To: "R?bert SZAKSZ" <robert at szaksz.eu> >Cc: nut-upsuser at lists.alioth.debian.org >Sent: Monday, November 16, 2015 3:20:17 PM >Subject: Re: [Nut-upsuser] Contact-closure UPS > >[please use reply-all when responding - the list does not modify the

On 12/17/2015 10:50 PM, hyouko at gmail.com wrote: > Can you try the nutdrv_qx driver with a debug level of 5 (i.e. five D > flags, nutdrv_qx -a upsname -DDDDD )? Attached is a logfile. -------------- next part -------------- A non-text attachment was scrubbed... Name: nutdrv_qx.log Type: text/x-log Size: 5727 bytes Desc: not available URL:

Hallo group, I am running openSUSE 10.3 with nut-2.2.0-20 installed. I have configured it as mentioned in /usr/share/doc/packages/nut/README.SUSE. on starting nut using "rcupsd start" i get following: # Starting NUT UPS monitor done Broadcast Message from root at pane (somewhere) at 22:27 ... Communications with UPS myups at localhost

Hi Mutlu, 2009/8/7 Mutlu T. <cmtunc at gmail.com> > Redirecting to debian.org domain due to being rejected as spam by free.fr > > > ------- Forwarded message ------- > From: "Mutlu T." <cmtunc at gmail.com> > To: arnaud.quette at free.fr > Cc: > Subject: New NUT HCL entry / (brand)Inform (series)Informer Compact > Date: Fri, 07 Aug 2009 15:31:04

Hi There, We have this rather large-ish floor-standing Best Axxium Pro, Model Series 0650. I tried using both the "bestups" and "blazer_ser" drivers with it, but no go. So before I go any further: *Should* one of these work with it and, if not, do I have any options? (E.g.: Modify a current driver, resuscitate one that was started and abandoned, etc.? I can code.) My test