similar to: (no subject)

Thank you lots! Finally I have everything working! Which are the ups.status I can use with ups in dummy mode? I have seen only OB, LB, OL... thank you Andrea 2017-07-04 19:55 GMT+02:00 Charles Lepple <clepple at gmail.com>: > On Jul 3, 2017, at 11:06 AM, Andrea de Lutti <adelutti at gmail.com> wrote: > > > > ?I would like that NOTIFYCMD points to upssched?. > >

On Jun 27, 2017, at 9:23 AM, Andrea de Lutti <adelutti at gmail.com> wrote: > > Sorry, I didn't received it... You should be subscribed to the list now. > I don't have any REPLBATT message Right, you would only get REPLBATT messages when the UPS reports that the battery *needs to be replaced* (and then at regular intervals per the upsmon.conf parameters). > , but

Sorry, I didn't received it... I don't have any REPLBATT message, but when in battery test I have OL CAL status: it would be good to have the result. Anyway I still not receive any email on any test (power cord disconnected and/or reconnected for example) Does the runtime calibration test alter the values of ups.conf? Or do I have to change it manually? Which would be the right procedure

On Jun 26, 2017, at 7:03 AM, Andrea de Lutti <adelutti at gmail.com> wrote: > > Are there no warnings for battery test? not sure if you saw my reply on 2016-06-17: Do you mean a notification that a test is in progress, or something for the results? There is the REPLBATT message in upsmon when the battery test fails, but I don't think the generic Qx protocol supports the RB

Good morning again, I have finished some tests and the driver works perfectly for shutting down the server and a client, both Ubuntu 16.04. I have to change the battery, I am unable to test with 100% load and now I have 5 minutes of battery power with a load of 18%. I am still unable to send email notifications, I have enabled all the warnings in upsmon.conf: NOTIFYFLAG ONLINE

Thanks mates, as suggested I have added runtimecal = 240,100,720,50 default.battery.voltage.low = 10.4 default.battery.voltage.high = 13.8 (the actual charging voltage) In ups.conf I have also added the startup procedure in rc.local file, everything is fine... I have only to make a deep test. Is there a way to add a NOTIFYMSG value for the battery test? Thank you lots Andrea

On Jun 16, 2017, at 2:20 AM, Andrea de Lutti <adelutti at gmail.com> wrote: > Using 'guestimation' (low: -0.866667, high: -1.083333)! > Initial battery charge undetermined > Driver failed to start (exit status=1) The "low" and "high" voltages should correspond to the battery voltage when it is discharged (LB) and charged, respectively. For a 12V

Ok, I am running NUT in dummy mode. I have added a new ups in ups.conf [dummy] driver = dummy-ups port = upsc.dev desc = "dummy ups for testing purposes" upsc.dev has been generated by exporting the Elit configuration. I have added the monitor line in upsmon.conf and the "exec" flags (all the events) MONITOR dummy at artu 1 user pass master SHUTDOWNCMD

> > , but when in battery test I have OL CAL status: it would be good to > have the result. > > "OL CAL" or "OB CAL"? If the UPS is powering the load from the battery > during calibration, it should report "OB CAL". The ONBATT handler in > NOTIFYCMD can check for CAL at that point. > > I don't think we considered the case where CAL is

On Mon, 3 Jul 2017, Andrea de Lutti wrote: > MONITOR dummy at artu 1 user pass master > SHUTDOWNCMD "/sbin/shutdown -h +0" > NOTIFYCMD /usr/local/bin/upssched-script Hi, As far as I can see, what you are getting in syslog corresponds correctly to what you have specified. You have specified that upsmon is to call upssched-script _directly_. This means that the argument to

Hi, it's me again. I haven't yet tested my UPS with full load, but I have tried to insert some values in ups.conf, I have kept the example on the blazer_usb driver hel page: runtimecal = 240,100,720,50 When I try to start the driver, I receive root at artu:~# upsdrvctl start Network UPS Tools - UPS driver controller 2.7.2 Network UPS Tools - Megatec/Q1 protocol USB driver 0.11 (2.7.2)

On Jun 29, 2017, at 6:52 AM, Andrea de Lutti wrote: >>> Anyway I still not receive any email on any test (power cord disconnected and/or reconnected for example) >> >> Oh, I misinterpreted "working script" as a script that was sending email, rather than work-in-progress. Does that same command work from the command line? Can you add something like "logger"

On Jan 27, 2019, at 2:36 PM, Phil Stracchino <phils at caerllewys.net> wrote: > > SO, my full load on my core UPS is two Dell R610s, one Sun X4540, one HP > DL360p gen8, two six-core Thuban-II workstations plua their monitors, > and the network stack and KVM. > > The APC SU3000RM (3KVA) that blew up last week considered this to be > just short of 60% load. > The new

2017-06-11 14:10 GMT+02:00 Andrea de Lutti <adelutti at gmail.com>: > So....seems so better... > > Each time I rebbot, I miss the /var/run/nut folder... > > root at artu:~# upsdrvctl start > Network UPS Tools - UPS driver controller 2.7.2 > Network UPS Tools - Megatec/Q1 protocol USB driver 0.11 (2.7.2) > Can't chdir to /var/run/nut: No such file or directory >

On Tue, 29 Sep 2020, João Luis Meloni Assirati wrote: > The UPS I am developing a driver to is able to report several flags for > critical hardware conditions, like overheat, overload, inverter failure, > output short etc. What should be the correct policy of operation when such a > condition occurs? I think that the an UPS in such a condition is not reliable > and therefore a

Hi, I have used the truss command as directed. I have attached both the driver output and the last few sections of truss output leading to the hang. Both outputs end at the CTRL+C i pressed when i was forced to end the processes. Hope this is helpful. Please bear with me if i didn't run it with the right options etc - as I mentioned, I'm a little new to Solaris. Regards, Richard On

On Jun 7, 2017, at 12:54 AM, Andrea de Lutti <adelutti at gmail.com> wrote: > > > Hi, I have tried several drivers for make my Elite UPS working. > With blazer_usb I can contact it, but I have no informations. This is the best result. > > OS: Ubuntu Xenial 16.04.2 LTS > NUT Version: Nut 2.7.2-4Ubuntu1 (Installed from Ubuntu Software Center) > Device name: Elite UPS

On Jun 8, 2017, at 9:15 AM, Andrea de Lutti <adelutti at gmail.com> wrote: > > Thank you for your reply Charles, > this is the "upsc" result: > > root at artu:~# upsc ups at localhost > Init SSL without certificate database > Error: Unknown UPS > Use the name from ups.conf in front of "@localhost". > Trying with nutdrv_qx, protocol megatec

On Jul 3, 2017, at 11:06 AM, Andrea de Lutti <adelutti at gmail.com> wrote: > > ?I would like that NOTIFYCMD points to upssched?. > If I understand correctly, Roger is pointing out that your configuration is confusing upssched and upssched-script. Since you are using Ubuntu, upsmon.conf should contain "NOTIFYCMD /sbin/upssched". Similarly, upssched.conf should contain

Thanks for your help. I have posted information, but I think I have answered myself, so maybe you haven't got an info. Sorry, using a mailing list is new for me ;-) Let's forget about the QNAP problem. It seems that although upsc is getting correct status information ("OL", "OB", "OB LB", OB CAL"), including calibration state, the QNAP special program