similar to: APC ups bx1400UI

Gabor: note, these HCL reports go to the nut-upsdev list. Begin forwarded message: > From: Gabor Tjong A Hung > Subject: Re: Network UPS Tools - Compatibility List > Date: September 3, 2013 2:18:31 PM EDT > > Sorry, > I just noticed the "If your device isn?t listed" part: > > [HCL] Forza FX-1500LCD supported by blazer_usb > > > [root at freenas] ~#

I'm looking for a driver for and old uninterruptible power supply (UPS), Eaton Powerware 9125 2500U. I want to use it with my FreeNAS server. I looked a the list and didn't see a driver for it: http://www.networkupstools.org/stable-hcl.html?manufacturer=Eaton I see a driver for the 9130; any idea whether it will work with a 9125? Any other ideas for connecting the 9125 to a FreeNAS

On Sep 19, 2014, at 4:03 PM, Nello Lucchesi <nello at octobergroup.com> wrote: > I'm looking for a driver for and old uninterruptible power supply (UPS), Eaton Powerware 9125 2500U. I want to use it with my FreeNAS server. > > I looked a the list and didn't see a driver for it: > > http://www.networkupstools.org/stable-hcl.html?manufacturer=Eaton > > I see a

Hey guys, :) recently, I installed Cyberpower PR2200ELCDRT2U, however, I have not managed to get this UPS working with FreeNAS 11, yet. According to compatibility list, PR2200 should work fine, when using powerpanel driver: http://networkupstools.org/ddl/Cyber_Power_Systems/ http://networkupstools.org/ddl/Cyber_Power_Systems/PR2200.html However, when trying to establish a connection between

Dear NUT users/developers, I'm having trouble while trying to configure the UPS APC BZ2200BI-BR[1] in NUT, which despite having a USB cable it apparently communicates using the serial protocol. The relevant output of 'lsusb' is: Bus 002 Device 004: ID 051d:c812 American Power Conversion The device is registered as /dev/ttyACM0 and uses the kernel module 'cdc_acm' (USB

Dear Charles, thanks for your quick answer and your information! I didn't know there is a difference in the PR-series between old and new. So thanks for this valuable information! usbconfig dump_device_desc shows: ugen0.2: <CyberPower Systems product 0x0601> at usbus0, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON (50mA)

The Hardware Compatibility List page on our website said to report any omissions in the list to this address. I bought a CyberPower UPS Model *LX1500GU*. It looks similar to the *CP1500AVRLCD*. My intention is to configure it in FreeNAS (FreeBSD). The FreeNAS user guide says it uses NUT to provide UPS support an contains a link to your website for a list of drivers of supported UPS devices. I

I'm using FreeNAS 9.1, and I've just got an APC Back-UPS CS 500. In theory it's supported by NUT, but the latest released version (2.6.5) doesn't have support for it (the driver reports an error, which is apparently due to an overflow). According to a thread on the mailing list, Back-UPS ES series requires a fix that's in source control, and CS series requires an additional

I have a Cyber Power LE1000DG UPS I got from Best Buy this weekend. I plan to use it with a TrueNAS scale system, and it is connected via USB. Vendor link: https://www.cyberpowersystems.com/product/ups/battery-backup/le1000dg/. TrueNAS has you pick a UPS driver. I could not find any "LE" related models on https://networkupstools.org/stable-hcl.html (which is the list TrueNAS uses). Per

Dear Sir or Ma'am, I have set-up a very functional NAS in my home using Freenas 0.7.2.5543. I had problems when losing power to the NAS. When I'd power it back on, my Raid 5 array and other disks would say that it was not properly dismounted, until I erased the disks, reformatted and remounted. The problem would then go away. I have since put an UPS between my NAS and the power to

Dear Sir or Ma'am, I have set-up a very functional NAS in my home using Freenas 0.7.2.5543. I had problems when losing power to the NAS. When I'd power it back on, my Raid 5 array and other disks would say that it was not properly dismounted, until I erased the disks, reformatted and remounted. The problem would then go away. I have since put an UPS between my NAS and the power to

On Aug 18, 2013, at 12:14 AM, Lyndon Drake wrote: > I'm happy to test an updated build, but have no idea about how to go about doing a build in the first place. Could someone help me in the process of creating a snapshot build for FreeNAS? I am not familiar with the specifics of building for FreeNAS, but our BuildBot instance is making source snapshots again:

On Mar 20, 2014, at 10:01 AM, Douglas A. Augusto wrote: > Dear NUT users/developers, > > I'm having trouble while trying to configure the UPS APC BZ2200BI-BR[1] in NUT, > which despite having a USB cable it apparently communicates using the serial > protocol. > > The relevant output of 'lsusb' is: > > Bus 002 Device 004: ID 051d:c812 American Power

Hi all ! I have a little problem using NUT from FreeNAS. Operating system FreeBSD 8.3-RELEASE-p4 (FreeNAS 8.3.0 BETA 2) UPS American Power Conversion/Back-UPS CS 650 FW:817.v7 .I USB FW:v7 NUT Driver Network UPS Tools - Generic HID driver 0.37 (2.6.5) USB communication driver 0.31 Trying to configure the UPS from FreeNAS failed so I try to investigate which is the problem. Running

Hello, I use a UPS APC 800VA. Use it with Openmediavault + Ups Nut plugin. My UPS is not in your list. :( I try in "Driver configuration directive" driver = usbhid-ups port = auto I have this in the log : omvhome upsmon[21683]: Poll UPS [ups at localhost] failed - Driver not connected Khampol.

Hello, I need help configuring my USB connected UPS "Emerson Power Liebert PowerSure PSI 1440" to my freebsd machine, using NUT. here's the manufacturer's product page http://www.emersonnetworkpower.com/en-US/Products/ACPower/Pages/LiebertPowerSurePSILineInteractiveUPS10003000VA.aspx I'm not a BSD expert, so please ask me for any information you need. regards Daniele

Hi, Recently I got three units of this nobreak [0]: The intention is connect it with some file server and/or web server. I found the NUT via FreeNAS [1] , and the contribuition [2] of Ulisses and Rodrigo about this vendor SMS, in Brazil. But, initially, i'm trying to apply the Ulisses patch (for smsbrasil driver) in a Debian Server, with no success. Can anyone help me about the patch in

Folks, I've asked this question on the FreeNAS forum but there are no ideas there as it looks like it's a NUT issue. Original question: https://forums.freenas.org/index.php?threads/apc-ups-reporting-wrong-input-voltage.60888/ the nut driver is reporting the wrong input voltage. I am in the UK, 230V but it's reporting circa 108. If I connect it to the laptop and run powerchute it

Hello Charles and Douglas, I really believe that BZ2200-BR model is the same as mine BZ1200-BR, with different capacity. If you see the BZ2200-BR specs you will notice the manufacturer "APC-Microsol". Those no-breaks have a USB port in it, but in fact it is a serial<->usb cable, usually uses the port "/dev/cuaU0". In mine, the serial<->usb chip is from FTDI, and

Greetings all, Anyone have a clue on this behavior (see below) on this behavior with FreeNAS-8.3.0-RELEASE-x64 (r12701M) on a TrippLite 1500LCD UPS? NUT version is 2.6.5 Using the following profile: Tripp-Lite ups 2 Smart1500LCD USB (usbhid-ups) I get the following: Dec 10 21:40:12 nas6 kernel: uhid0: <Tripp Lite TRIPP LITE UPS, class 0/0, rev 1.10/0.02, addr 2> on usbus1 Dec 10 21:40:12