similar to: Regarding the Asium P700

I have been using the Asium P700 for about 4 months, running Debian Wheezy 7.9,? and would like to submit the UPS for inclusion in your list of supported devices.? ASIUM P700 (650VA/360W) | ? | | ? | | ? | ? | ? | ? | ? | | ASIUM P700 (650VA/360W)Prices only valid for purchases within the US. No PO Box deliveries. | | | | View on www.asiumpower.com | Preview by Yahoo | | | | ? | Not sure

No, the Battery Temp does not change. It is always 25C. I don't know why the ups.delay.start is that high. Is that user configurable? Yes, I have tested the automatic shutdown. Works well. Yes, the instant commands work, at least those I feel comfortable testing. Battery test work fine. I have not enable the write to variables. Did not know that it might be necessary. John Hart -----

Greetings.? I have been using NUT for some time now and have not had any issues until yesterday.? I was trying to get my NOTIFYCMD script working and was making modifications to upsmon.conf .? After making the mod to upsmon.conf I invoked upsmon -c reload and a few minutes later the system shut down.? There was a loss of communications with the UPS.? I have an Asium P700 UPS and use the blazer_usb

Looking for some help with this UPS. ?I am running Debian Jessie 8.1 (32 bit). ?I live inCosta Rica so UPS purchase options, in my price range, are fairly slim. ?I purchased thereferenced UPS, which works with WinPower software, but am really hesitant to installWinPower as I don't know how it might affect things and don't want to break the system. When I was still running Wheezy, I

2013/12/6 Fabio Cecamore <ceca_89 at hotmail.com>: > Hi all, Hi > I've problem with the management of my AtlantisLand UPS, the UPS don't want > to wake up after the whiteout and I don't have any idea why.. Some (very old) units are known to have problems with small values for ondelay (hence the default 3 minutes value):

As a follow up on my last message, where I talked about loss of USB communication with my Asium P700 UPS, I was thinking about some possible improvements.? 1.? When communications are lost, instead of shutting down immediately why not set a flag and then stop the driver and then restart the driver.? If communication is not re-established, and the flag was set, then shut down the system.? Perhaps

Welcome, Acctualy, I'm try to poweroff my ESXi (6.7). Virtual machine with Ubuntu and redirected USB port with APC Back UPS CS 650, have nut-server and send info to ESXi. When battery is low, ESXi poweroff gracefully all VM and same ESX go down. This work fine and don't have any problem. But important to me, is set to more offdelay on UPS than the default 60 sec. (cut off power socket

On Nov 21, 2015, at 10:36 AM, john hart <jsamcr at yahoo.com> wrote: > > Greetings. I have been using NUT for some time now and have not had any issues until yesterday. I was trying to get my NOTIFYCMD script working and was making modifications to upsmon.conf . After making the mod to upsmon.conf I invoked upsmon -c reload and a few minutes later the system shut down. There was a

As an update to my first message, sent July 13, I am totally out of my league.I installed nut (apt-get install nut) on Debian Jessie. ?Went through the process of modifying?ups.conf and copied the udev ( cp /lib/udev/rules.d/52-nut-usbups.rules /etc/udev/rules.d/ ) When I ran ?upsdrvctl start ?I got a message about the usbhid-ups driver. ?It appears that NUTis not configured with the driver. ?The

Hi all, after a change of UPS (to Atlantis Host Power 851) I began to use the new driver blazer_usb and compared to old one (blazer used with serial connection) I noted more CPU use and errors in dmesg: [...] [256712.584370] usb 4-5: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33 rq 9 len 8 ret -110 [256789.640795] usb 4-5: usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 33 rq 9 len 8

Thanks for your reply Hyouko, these are the actual not working parameters: driver.parameter.offdelay: 60 driver.parameter.ondelay: 5 ups.delay.shutdown: 60 ups.delay.start: 300 and the UPS don't wake up after the whiteout.. My UPS is not so old :( Il 09/12/2013 16.04, hyouko at gmail.com ha scritto: > 2013/12/6 Fabio Cecamore <ceca_89 at hotmail.com>: >> Hi all, > Hi

Dears, I finally resolve my problem, I just make symbolic link: [test at box var/run/]# ln -s -T /var/state/ups/ nut Now I finally got services online: # /sbin/service ups start Starting UPS driver controller: [ OK ] Starting upsd: [ OK ] Starting UPS monitor (master): [ OK ] BUT, on upsc I

On Tue, Oct 2, 2018 at 3:59 PM Charles Lepple <clepple at gmail.com> wrote: > > On Sep 27, 2018, at 6:59 PM, Gabriel <jarod125 at gmail.com> wrote: > > > > Hi, > > > > I'm struggling with a peculiar issue with my UPS. After a power > > outage, the devices powered by it properly shut down via nut. > > Eventually, the UPS also goes down.

Hello, Ren?. > You can change the parameter > ups.delay.start into your UPS to set the "Interval to wait before > (re)starting the load (seconds)" > > use upsset to change the value. So far, the ups.delay.start parameter in my MGE Protection Center 675 has always been equal to the driver.parameter.ondelay parameter (which equals the ondelay argument in ups.conf).

Time, not sure who owner is, but I've tried as both admin and myself, to no avail. ?However, I told you that mesg is y, buti tried to send a mesg using ?' write ' ?and it says I have messages disabled. ????? ? I did that by opening two?terminals, on I logged in as ' su ', and sent the message from there. ?Is that peculiar? Might account for why I am notgetting anything from

Hello, I am trying to make my UPS system working with NUT but with no success. I got "No supported UPS detected" message. I use the blazer_usb driver since it was proposed to me by the web site. My NUT version is : 2.7.1 (installed from standard RPM), release 2.41 The UPS identification: INFOSEC X4 RM PLUS linux-2qya:~ # /usr/lib/ups/driver/blazer_usb -a infosec Network UPS Tools -

After issuing this command: /upsrw -s ups.delay.shutdown=180 -u admin -p mypassword myups /I obtain this error:/ Unexpected response from upsd: ERR READONLY /After issuing this command:/ upsrw myups /I obtain no output./ /In my /upsd.users/ file I have these settings: /[admin]// //password = mypassword// //actions = SET// //instcmds = ALL// // //[myuser]// //password = mypassword//

Hello there. Have been experimenting with an APC Smart-UPS 1500 RM and would like to share the results of my research. I hope this could be of help to people having this kind of units. I would also like to give something back to the NUT community. :) Here are the details of the unit in question (a 1500 VA rack mountable one): Model: Smart-UPS 1500 RM Firmware revision: 617.3.I USB firmware

>> [Roger wrote:] >>> By the way, do you have offdelay and ondelay values in your ups.conf ? >> >> No, I haven’t. I just added. Should I add more lines here? >> >> maxretry = 3 >> >> [ups] >> driver = usbhid-ups >> port = auto >> desc = "CPS" >> pollinterval = 15 >Yes, ondelay

Tim, Thanks for the feedback. ?I am the only user (standalone system), but I checked 'mesg' and made sure it was set?to 'mesg y' . ? And the execute permissions for wall are ? rwxr-sr-x ?and the filename is has a ?kind of orange highlightedbackground. Don't know what that means. John?"Science is organized common sense. Philosophy is organized piffle" -attributed to