similar to: linphone calls not missed due to cause not 487

Hi Sergio On 16.10.20 at 07:54 sergio wrote: > Sometimes, linphone shows missed calls as missed. Look like asterisk > replies with cause=487 that time, but I can't understand why. > > Grandstream always shows calls as missed ones. > > How should I investigate this? You could try to reproduce it while activating pcap traces and analyze it afterwards - or you could

Sometimes, linphone shows missed calls as missed. Look like asterisk replies with cause=487 that time, but I can't understand why. Grandstream always shows calls as missed ones. How should I investigate this? -- sergio.

On 16/10/2020 10:11, Michael Maier wrote: >> Sometimes, linphone shows missed calls as missed. > You could try to reproduce it I can't reproduce it, it happens less than once a month. -- sergio.

Hello. I have two records in dialplan: exten => testA,1,Dial(PJSIP/outgoing/sip:thetestcall at sip.linphone.org) exten => testB,1,Dial(PJSIP/outgoing/sip:thetestcall at iptel.org) Calling testA works fine while testB fails with "CONGESTION". Adding debug for console shows that pjsip_resolver.c does `New queries added, performing parallel resolution again` for linphone after

Hi, I dial on A* from a linphonec to a Playback() extension, then suddenly the sound stops after a while, without any notice. I enabled debug both in linphone and A*, and the RTP packets are sent from A* and received from linphone. It doesn't matter whether I choose alaw, ulaw, gsm as codec (besides changing cpu load of course). How can I debug it? I'm using A* 1.6.2 and both linphone

Hi folks an issue I don't understand. I'm running * stable 1.0.3 on public internet, with following iax.conf / sip.conf entries: iax.conf [100] type=friend username=Foo context=default auth=md5,plaintext,rsa secret=secret host=dynamic callerid="Foo" <100> qualify=no sip.conf [10] type=friend username=Bar context=default callerid=Bar <10>

Hi All, I am getting this error during make. please help me./ speexec.c: In function `speex_ec_process': speexec.c:112: syntax error before "noise" cc1: warnings being treated as errors speexec.c:133: warning: implicit declaration of function `speex_echo_state_reset' speexec.c:148: warning: passing arg 5 of `speex_echo_cancel' makes pointer from integer without a cast

Today's "frustrated programmer" award goes to Linphone, which has the following debug output: > (linphone:28655): LinphoneCore-WARNING **: this fucking remote sip phone did not answered properly to my sdp offer! I get this message when I connect to linphone using a softphone, or when I try to use linphone to connect to asterisk and listen to an announcement. I suspect that

Hi John, 1. Could you get any further, in your quest for working BLF with linphone ? 2. Have you tried with a different Linphone version (4.12 is pending on Linux, packaged as an AppImage, or 4.11 exists on iOS/Android/Win10) ? Best regards Le mer. 25 mars 2020 à 15:06, John Hughes <john at calva.com> a écrit : > > On 23/03/2020 18:51, Joshua C. Colp wrote: > > On Mon, Mar

hi all, please help... I am calling in the simplest way among two linphone clients connected to one asterisk server... the call ends on one side without any sign of problem, while on the other side it stays connected. I checked the SIP dialogue and at some point the server sends a BYE message to one party I have no timeout set, though the duration of a call is always around 20s. the two

It seems a new Linphone 4.2 is to be published next week ! Hopefully, ... Le ven. 5 juin 2020 à 13:34, John Hughes <john at calva.com> a écrit : > On 26/05/2020 15:33, Olivier wrote: > > Hi John, > > 1. Could you get any further, in your quest for working BLF with linphone ? > > The patches to get linphone-3.12 BLF working with Asterisk are here: > >

Hi all - I am using asterisk 13.27.0 with Linphone. I turned off all codes on linphone except the one I want to try. For example: opus and speex (so only one enabled at a time). Then did this same on asterisk for the linphone extension. disallow=all allow=speex (for example). Then I place my call and the call fails. if I enable something like gsm, ulaw, alaw the call works fine. Why does the

So I've got a bit further with my  project to get BLF working between asterisk and linphone. Initially asterisk was rejecting linphone's SUBSCRIBE messages because they didn't have an Accept: header. I've fixed that and now the initial SUBSCRIBE messages work and I see all my online contacts in green. But after a few minutes linphone attempts to renew the subscriptions and

Hi, I have * working with X-Lite and Sipura adapters, but I have one person who is linux based, and is trying to use Linphone and Kphone. His end works, but I get very bad echo on my end. Have any of you folks been able to get linux based soft phones working well with *? I'd appreciate links to howtos/docs if you have them, and/or samples of working configs for * and the linux

Hello, has anyone running a linphone-application on am335x (like beaglebone) with opus codec. My CPU has extreme high load, wenn ist start with opus codec. Is there a possibikity tu optimize f?r this single core ARM? Thanks Helmut Sholz ______________________________ BAYERISCHER RUNDFUNK Rundfunkplatz 1 80335 M?nchen HA IT und Medientechnik Abteilung Systemservice Funkhaus FG Sendungssysteme

I am dying here with linphone (not sure if it is crap software or just me being an idiot) but out of the box debian installations of two linphones fail with a "Got SIP response 415 "Unsupported Media Type" back from 192.168.1.3" Can anybody recommend a particular SIP soft phone that broadly satisfies the following criteria? 1. Run on linux. 2. Simple to use and setup. 3. Is

On 23/03/2020 18:51, Joshua C. Colp wrote: > On Mon, Mar 23, 2020 at 2:45 PM John Hughes <john at calva.com > <mailto:john at calva.com>> wrote: > > > > Why is asterisk giving an error 500? I can find no reason, there > is nothing in any log. > > > The sequence number is from the past. The first SUBSCRIBE is sequence > number 22 (check the

Hi All, I am getting this error during make. please help me./ speexec.c: In function `speex_ec_process': speexec.c:112: syntax error before "noise" cc1: warnings being treated as errors speexec.c:133: warning: implicit declaration of function `speex_echo_state_reset' speexec.c:148: warning: passing arg 5 of `speex_echo_cancel' makes pointer from integer without a cast

On 26/05/2020 15:33, Olivier wrote: > Hi John, > > 1. Could you get any further, in your quest for working BLF with > linphone ? The patches to get linphone-3.12 BLF working with Asterisk are here: http://perso.calvaedi.com/~john/linphone-3/ They're pretty damnned trivial: 1. add the "Accept" header to the SUBSCRIBE message so asterisk doesn't reject it. 2.

Where might I find an rpm for Centos?