similar to: Various extensions ring once and go to voicemail - Thomas Peters

On 1/14/19 4:02 PM, Duncan Turnbull wrote: > > > Sent from my iPad > > On 15/01/2019, at 10:34 AM, Thomas Peters <TPeters at mcts.org > <mailto:TPeters at mcts.org>> wrote: > >> Duncan: >> >> You may have it right—I took one phone and set the ring time to 60 >> seconds. I now get about 4 rings on that one. >> >> I wonder how I

Duncan: You may have it right-I took one phone and set the ring time to 60 seconds. I now get about 4 rings on that one. I wonder how I can change the timing source. Thomas M. Peters | Sr. Systems Administrator | tpeters at mcts.org<mailto:tpeters at mcts.org> Desk: 414.343.1720 | Helpdesk: x3400 or helpdesk at mcts.org<mailto:helpdesk at mcts.org> Milwaukee County Transit System

We have an old Asterisk 1.8.7.0 system desperately need to keep alive for another 6 months or so. We had all kinds of hardware problems, so we virtualized it. Now, random extensions ring once and go straight to voicemail. I went to one of the affected extensions and changed the ring time from the default (20) to 26. Still one ring. I changed it to 30. Now I get two rings. Other extensions ring

Hello all, I hope someone can help me with this old Asterisk version. I have to run this version because of a custom IVR written on it. Porting it would take much too long and we'd have to hire a consultant because of all the hooks it has into Oracle databases and real-time information. We have a brand-new Avaya phone system in place and we will be cutting over to it in late March 2019.

Thanks for the reply John. About 85-90% of what this box has to do is just handle calls, but it also has options to transfer calls to the main phone system, which up to now has been another asterisk box. For example, you can hit 6 to be transferred to the Lost & Found Department. I do have allowguest set to “yes” already, but of course I also have type=peer and the other stuff for a sip

>Information on timing sources can be found here: >https://wiki.asterisk.org/wiki/display/AST/Timing+Interfaces >As noted on that page, ConfBridge can use any timing interface Asterisk >provides, and is not limited to the DAHDI timing interface. Generally, >timerfd is a good timing interface. >That aside, I would try to rule out external issues with the garbled audio

hi: my current system is 1.6.2. I have dahdi hardware card. I must disable res_timing_timerfd module or sometimes phone calls would become silent suddenly. I don't know the situation in 1.8. I heard that timing is still a problem in 1.8. should I keep using "res_timing_dahdi" or I can use "res_timing_timerfd" to get some benefit if I upgrade to 1.8? thank a lot for

Ok, commented out that line. It's still doing it. Reloaded dialplan. Please don't tell me I have to restart asterisk. Thomas M. Peters | Systems Administrator | tpeters at mcts.org Desk: 414.343.1720 | Helpdesk: x3400 or helpdesk at mcts.org >>> Tiago Geada <tiago.geada at gmail.com> 6/26/2015 12:07 PM >>> messages => error states to log error messages to

Switched from Asterisk 1.8 to 13.3.2. Now it logs to /var/log/asterisk/full (good) as well as /var/log/messages (not good). Anyone know why? # grep -v "^;" logger.conf [general] [logfiles] console => notice,warning,error messages => error full => notice,warning,error,debug,verbose,dtmf,fax Thankfully, the .../full logs are rotating properly now (thanks Dale) but we don't

Folks, I've read some sources claiming that Asterisk does not need DAHDI for timing in 1.6.1. Is this true? Searching the web, all I can find is pages celebrating the fact but no actual documentation on which version it was introduced in and how one would go about configuring an external time source. I'm having a devil of a job trying to compile DAHDI on a hosted Xen VM and thought I

Ah I see, in theory it's possible then. We don't have any IVRs or anything which requires key presses, there isn't even voicemail on this particular phone system so I don't think it will be too much of a problem. I've also updated the firmware on the Cisco phones that have had the issue, just to see if that solves the issue but as it's been going on for a while, I'm

Hi! I have Asterisk 1.6.1 installed on OpenSuSE 11.0 running with choppy sound. One specialist on the forums asked me if I have DAHDI configured, he assumed that this could be cause of choppy sound problem. > dahdi_test Unable to open dahdi interface: No such file or directory Do I need to configure DAHDI even if I do not have any Zaptel devices? Is there any guide for configuring

I'd like to start configuring my Avaya 9608G phones for use on Asterisk / FreePBX / PBX-In-a-Flash. I'm using a variety of other phones on my system without major issues. I've read the discussion back in March, May and August of 2016, but unfortunately, my difficulty is much more basic. I think it has to do with DHCP, specifically, what options I'm offering the phone via DHCP.

Hi Tom, Thank you for your informative and helpful reply. I had considered using the relaxdtmf setting but held off this due to not using any physical connection hardware -Asterik uses both SIP in and out from an upstream provider (Gradwell.com). Is it still possible to set this when using SIP trunks only and not physical hardware? The box does have a Digium ISDN card but the ISDN is no longer

Hi all I am using asterisk 11.24.1 on a centos 5 machine. kernel 2.6.18 flavor. (x86_64). I have about SIP 150 endpoints on it. when I send a message I'm getting garbled audio. I used to have a single PRI card in the box - but something happened and that connection no longer worked. I removed the card and also removed the system.conf and chan_dahdi entries. I am using ConfBridge in a PA

Hi all Sometimes (about every three months) some of my Asterisk 1.8 boxes will start running this message thousands of times in the CLI: [Feb 12 14:18:23] ERROR[28129]: res_timing_timerfd.c:180 timerfd_timer_ack: Call to timerfd_gettime() error: Invalid argument [Feb 12 14:18:23] ERROR[28129]: res_timing_timerfd.c:180 timerfd_timer_ack: Call to timerfd_gettime() error: Invalid argument [Feb 12

Hi Gang, My production box with my DAHDI cards is a 1.4.26 build. I have 3 test machines that I do IAX communication with. Machine 1 is a real Dell POWEREDGE 1500 running CENTOS running 1.4.30. Machine 2 is a SUSE 11.1 VM running 1.4.30. Machine 3 is another SUSE 11.1 VM running 1.8.0. I can SIP into all 4 machines and life is great. When I try to IAX from the live machine to

Hi, We heavily use meetme/SLA functionality in Asterisk, and continuously run into issues with dahdi timing. The two errors we get are: ERROR[6518] res_timing_dahdi.c: Failed to configure DAHDI timing fd for 0 sample timer ticks WARNING[22024] app_meetme.c: Unable to write frame to channel Right now, dahdi in our setup uses the software timer (with res_timing_dahdi.so which gives much better

starting 161.1-beta3: chan_iax2.c:10925 build_user: Unable to support trunking on user 'iax-out' without DAHDI timing But I have these "timing" modules: ls /usr/lib/asterisk/modules/res_tim* /usr/lib/asterisk/modules/res_timing_dahdi.so /usr/lib/asterisk/modules/res_timing_pthread.so Do I need to do some magic to get these loaded? modules.conf is set to auto. Is this what

We are running Asterisk 1.8.5.0 with an uptime of 40 weeks. Just today our streaming music on hold stopped working. I remember when we had first installed 1.8 we had an issue where the streaming music on hold would not work because Music On Hold was using the DAHDI timing module. We needed the DAHDI timing module loaded so that paging would work. However, at that time we upgraded to 1.8.5.0 and