similar to: Avaya 9608G and DHCP and TFTP and HTTP oh my

Ok, to review, I'm trying to get Avaya 9608G to come up in a pure Asterisk environment-- no Avaya SBC or gateway or any other Avaya gear in sight. I have the phone working to the point where it boots up properly, then displays a Username and Password prompt, and says its extension is 123 and the time is 4:57p, which is wrong. But please don't tell me the only way to program up each

Right-- I've seen the Avaya document you cite below. It says "To administer DHCP option 242, make a copy of an existing option 176" but I don't have any example of option 176 or 242 to copy, and don't know what to do to /etc/dhcpd.conf to make it offer option 242. Then there's this long table of parameters to use with (presumably) option 242. I was hoping someone had a

Hello, Is there any reason why an IP-phone would pounder on port 5060 ? My firewall blocks the public IP because it thinks the remote IP is port scanning on port 5060. I think the phone is just registering but for some reason it does this repeatedly in a very short time. Oct 28 09:01:48 astserver kernel: Firewall: *UDP_IN Blocked* IN=eth0 OUT= MAC=00:00:00:00:00:00:00:00:00:00:00:00:00:00

i have installed the asterisk 1.6 before that installed the necessary packages in Debian, * i followed the steps as follows, root at astserver: ~# apt-get install unixodbc unixodbc-dev odbc-postgresql postgresql-8.1 postgresql-contrib postgresql-dev * then i installed the asterisk 1.6 version with the odbc modules as in the selected list. * then i created the database as asterisk and the user

Thanks for the reply John. About 85-90% of what this box has to do is just handle calls, but it also has options to transfer calls to the main phone system, which up to now has been another asterisk box. For example, you can hit 6 to be transferred to the Lost & Found Department. I do have allowguest set to “yes” already, but of course I also have type=peer and the other stuff for a sip

Duncan: You may have it right-I took one phone and set the ring time to 60 seconds. I now get about 4 rings on that one. I wonder how I can change the timing source. Thomas M. Peters | Sr. Systems Administrator | tpeters at mcts.org<mailto:tpeters at mcts.org> Desk: 414.343.1720 | Helpdesk: x3400 or helpdesk at mcts.org<mailto:helpdesk at mcts.org> Milwaukee County Transit System

Hello all, I hope someone can help me with this old Asterisk version. I have to run this version because of a custom IVR written on it. Porting it would take much too long and we'd have to hire a consultant because of all the hooks it has into Oracle databases and real-time information. We have a brand-new Avaya phone system in place and we will be cutting over to it in late March 2019.

The line you commented out was writing errors to /var/log/asterisk/messages The problem you are having is the logging to /var/log/messages via syslog. It appears that Asterisk is sending verbose logging out to syslog even though logger.conf does not have syslog configured. I am not sure why Asterisk is doing that, and I do not want to play on a production system. I added a filter to the

Hello All, I am trying to set up a cobbler server running as a guest on an isolated network. I'm having trouble figuring out how I can forward the DHCP and DNS traffic to this guest instead of DNSMASQ on the host. So far I have only tried to get dhcp working by enabling the 'allow-dhcp-server' on a guest named test and setting the $DHCPSERVER variable through a filterref parameter

Ok, commented out that line. It's still doing it. Reloaded dialplan. Please don't tell me I have to restart asterisk. Thomas M. Peters | Systems Administrator | tpeters at mcts.org Desk: 414.343.1720 | Helpdesk: x3400 or helpdesk at mcts.org >>> Tiago Geada <tiago.geada at gmail.com> 6/26/2015 12:07 PM >>> messages => error states to log error messages to

We have an old Asterisk 1.8.7.0 system desperately need to keep alive for another 6 months or so. We had all kinds of hardware problems, so we virtualized it. Now, random extensions ring once and go straight to voicemail. I went to one of the affected extensions and changed the ring time from the default (20) to 26. Still one ring. I changed it to 30. Now I get two rings. Other extensions ring

Switched from Asterisk 1.8 to 13.3.2. Now it logs to /var/log/asterisk/full (good) as well as /var/log/messages (not good). Anyone know why? # grep -v "^;" logger.conf [general] [logfiles] console => notice,warning,error messages => error full => notice,warning,error,debug,verbose,dtmf,fax Thankfully, the .../full logs are rotating properly now (thanks Dale) but we don't

After we upgraded to 1.2.12, we've been having issues with libvirt... it complains that our formerly valid guest definitions are now invalid: error: Failed to start domain XXXX error: internal error: Cannot instantiate filter due to unresolvable variables or unavailable list elements: DHCPSERVER We looked into this, and found that it's the XML validation that's failing: # xmllint

messages => error states to log error messages to 'messages' log file On 26 June 2015 at 17:50, Tom Peters <TPeters at mcts.org> wrote: > Switched from Asterisk 1.8 to 13.3.2. Now it logs to > /var/log/asterisk/full (good) as well as /var/log/messages (not good). > Anyone know why? > > # grep -v "^;" logger.conf > > [general] > [logfiles] >

On 1/14/19 4:02 PM, Duncan Turnbull wrote: > > > Sent from my iPad > > On 15/01/2019, at 10:34 AM, Thomas Peters <TPeters at mcts.org > <mailto:TPeters at mcts.org>> wrote: > >> Duncan: >> >> You may have it right—I took one phone and set the ring time to 60 >> seconds. I now get about 4 rings on that one. >> >> I wonder how I

Hi Rowland. The command (samba-tool user enable 'user') is used to enable a user account that has been disabled in AD, but it is not functional to unlock a user account that has been locked by wrong password. Anderson Hoffmann do Carmo MCP | MTA | MCDST | MCTS | MCSA | MS | MOS | ITIL-F | ISFS | CLOUDF | CI-SCS | VCA-DCV | 2016-08-01 13:51 GMT-03:00 Rowland penny <rpenny at

Hi Jason/Rowland Great news! the following procedure worked perfectly... I added at the end "Remove manually Windows DC entries in DNS" The script used in step 9 was " https://gallery.technet.microsoft.com/scriptcenter/d31f091f-2642-4ede-9f97-0e1cc4d577f3 " *Very thanks for all!* Anderson Hoffmann do Carmo MCP | MTA | MCDST | MCTS | MCSA | MS | MOS | ITIL-F | ISFS | CLOUDF

Hi all: I tried kvm on my ubuntu with the libvirt.xml file as follows: <domain type='kvm'> <name>instance-00000011</name> <memory>2097152</memory> <os> <type>hvm</type> <boot dev="hd" /> </os> <features> <acpi/>

Ah I see, in theory it's possible then. We don't have any IVRs or anything which requires key presses, there isn't even voicemail on this particular phone system so I don't think it will be too much of a problem. I've also updated the firmware on the Cisco phones that have had the issue, just to see if that solves the issue but as it's been going on for a while, I'm

Type the command pdbedit -Lvu username , what does it show on the Account Flags field? ----- Original Message ----- From: "Anderson Hoffmann do Carmo" <anderson.hoffmann at gsurfnet.com> To: "samba" <samba at lists.samba.org> Sent: Monday, August 1, 2016 2:04:48 PM Subject: Re: [Samba] Unlock domain user Hi Rowland. The command (samba-tool user enable