similar to: chan_pjsip ignoring endpoint device state (qualify) on dial

On 2016-08-09 10:06, Faheem Muhammad wrote: > trip time and Call Setup time of SIP Requests. > In case of GSM Network with high delay you need to set the T1 timer a > higher value like 1000ms (500 ms default). Similarly you can reduce the > Call setup time by configuring 'T2' upto you choice as per you telephony > network. Configure t1min, timert1 and timerb according to

Hello, Is there any equivalent of the CONNECTEDLINE function which can be called from an application using the AMI? Thanks for any ideas. -- David Cunningham, Voisonics http://voisonics.com/ USA: +1 213 221 1092 Australia: +61 (0) 2 8063 9019 -------------- next part -------------- An HTML attachment was scrubbed... URL:

I have a concern with Dial command, I want to enable a secondary route with a remote partner, if the first route fails then we use the second one : Solution1: it will try both (there will be 2 simultanious actives calls ringing) this is not clean when calling an endusers exten => _X.,1,Dial(SIP/${EXTEN}@remote-sip1,5 <mailto:SIP/${EXTEN}@remote-sip1,5> ) exten =>

On 10.12.2014 11:42, Frederic Van Espen wrote: > Hi, > > - Could you share the details of the SDP in each INVITE and OK packet? > - How are your SIP endpoints configured in asterisk sip.conf? (the SIP > trunk provider and the local endpoint) > - What type is the local endpoint? > > Cheers, > > Frederic > Frederic, I now have tried to describe the situation

Hey all! I recently tried the dtmf_mode "auto_info" on my setup to support endpoints that only understand SIP INFO as a fallback. My setup is the following: Endpoint A (RFC4733) --> Asterisk <-- Endpoint B (SIP INFO) Both are configured with "auto_info" dtmf_mode in pjsip.conf. What I ran into is, that DTMF sent from endpoint A to endpoint B is additionally sent via

hello, is it possible simultaneously use chan_sip and chan_pjsip? if yes, can you recommend settings i'm thinking about - chan_sip - for sip hardphones/softphones (sip udp 5060) - chan_pjsip - for webrtc -- --------------------------------------- Marek Cervenka =======================================

Dne 13.8.2015 v 17:20 Rusty Newton napsal(a): > On Thu, Aug 13, 2015 at 3:54 AM, Marek ?ervenka <cervajs at fpf.slu.cz > <mailto:cervajs at fpf.slu.cz>> wrote: > > hello, > > is it possible simultaneously use chan_sip and chan_pjsip? > > if yes, can you recommend settings > > i'm thinking about > - chan_sip - for sip

Hello, I finally got to look at chan_sip to chan_pjsip migration again. This time I’m having problems with influencing codec selection on originating (calling) channel. It looks like PJSIP_MEDIA_OFFER only works on outbound (called) channel and has no affect on calling channel. My experiments and function documentation (which says “Media and codec offerings to be set on an outbound SIP

Hello, Anyone? I have hard time to believe this is not possible with chan_pjsip. Anyway, may I ask how people handle the following scenario which I imagine should be quite common: - I have internal extensions talk to each other using g722. so their codec setting (with chan_sip now) is "allow=g722,ulaw" - I have carriers trunks that handle ulaw only (allow=ulaw) - calls between

Hello List, I tried to change the following parameters in sip.conf file, but looks like it cannot be changed, Defaut values: ;t1min=100 ;timert1=500 ;timerb=32000 I have changed to: ;t1min=100 timert1=100 timerb=6400 Sometime I can see too many retransmission of BYE to some of the UAs if UA is unreachable. Is there a way that I can reduce the number of retransmission of BYE message?

Hello Michael, you are referring to the following behavior - did I get it correctly?: outbound broken: asterisk offers g722 / g711 to provider (callee), callee answers g711. Asterisk now transcodes between caller and callee (g722 <-> g711). inbound works: call from provider: g711 -> asterisk drops g722 and passes g711 to internal callee -> no transcoding. As far as I know,

Greetings, I've noticed a problem that might originate from my Asterisk configuration, could use a hand in sorting it out. Problem is a 488 response from Asterisk whenever it gets RTP/SAVPF profile in the SDP. My current setup has Asterisk Kamailio realtime integration, and Kamailio uses dispatcher to route calls for Asterisk to handle. Now I have only one Asterisk, on the same machine as

Well, I'm trying to migrate to chan_pjsip so that I don't have to do that. It's so surprising that the issue so seemingly obvious and trivial hasn't been addressed yet that I wanted to query the collective wisdom of this list to verify my observations. Thanks for github pointer. Michael On 7/5/23 16:46, asterisk at phreaknet.org wrote: > On 7/5/2023 4:19 PM, Michael

Hello. I am using asterisk and chan_sip a lot of years. And newbie in chan_pjsip. Now i am transfering all from chan_sip to chan_pjsip. And have a lot of questions. First of... system: Asterisk 13.2 on slackware 14.1 Errors on outgoing call: [2015-03-03 00:18:58] ERROR[6794]: chan_pjsip.c:1778 request: Failed to create outgoing session to endpoint 'srv_d228' [2015-03-03 00:18:58]

Hello! I encounter the following problem (asterisk 11 and 13) with Teconisy as trunk provider with enabled qualify and default t1min (100ms): Teconisy most often doesn't answer the first invite before asterisk default t1min ended. Therefore asterisk sends one more invite. This second invite is answered by Teconisy with status 486 - Request terminated - Channel limit exceeded. (The second

I am using 1.8. I need to change timerb to 6500, that is, if there is no response of some sort in 6.5 seconds, consider the call failed and try another route. It does not matter what do I set for the other timers: T1min=100 timert1=100 Timerb=6500 The command "sip show settings" always shows Timer B=32000. Any ideas how can I reduce Timer B?

Hi Joshua thank you for the quick reply > Have you checked the Asterisk console when PJSIP is loaded to see if > the endpoint did not load for some reason? Does it show up in "pjsip > show endpoints"? Yes, the endpoint shows up. Endpoint: 11/(scrubbed from mail) Not in use 0 of inf InAuth: 11/11 Aor: 11

Hi Everyone, We're routing calls through Asterisk (dialing in via sip and then dialing out via SIP). We've noticed a curious behavior in chan_sip that doesn't persist with chan_pjsip. When examining the packet capture, we're seeing the SSRC changing constantly on the call. At first it happens over a variable interval (15s 6s etc) but eventually it ends up changing exactly every

Hello, I am having big problems with Xen virtual network interfaces. First I tried typical bridge support, no luck. The packets sent from dom0 to domU seemed to disappear somewhere. Then, to debug the problem I have set up a simple point-to-point link and still have the same problem. I am using Xen 3.0.4-1 and Linux 2.6.16.x in both dom0 and domU. I have tried kernel 2.6.16.35 and 2.6.16.41. I

The Asterisk Development Team has announced the release of Asterisk 13.8.0. This release is available for immediate download at http://downloads.asterisk.org/pub/telephony/asterisk The release of Asterisk 13.8.0 resolves several issues reported by the community and would have not been possible without your participation. Thank you! The following are the issues resolved in this release: New