similar to: RTP / NAT question ( pjsip )

Greetings ! My goal is to get Twilio trunking working, and with TLS/SRTP. I see this concerning message in my log: [Feb 7 16:50:26] ERROR[20596] res_sorcery_config.c: Could not create an object of type 'endpoint' with id ?twilio' from configuration file ?pjsip.conf? Thus, ?pjsip show endpoints? does not show the endpoint for the Twilio trunk. Hoping for a sanity check of

Hello All, I have an Asterisk server v13.1.0 running on EC2 and I am able to connect and register SIP devices and "see" them on the asterisk CLI. I am also able to place calls, but I am not able to hear any audio on either end after the call is picked up. I was wondering if you can tell me what a minimal configuration for Asterisk on EC2 looks like. My current pjsip.conf configuration

Hi first post, so hope I'm not violating protocol. Been using Asterisk as home phone and hobby use for nearly 10 years. I love this project. Anyway, would someone mind verifying my pjsip.conf ? This seems to work well for 14.3.1 but I get no rtp into my natted Linphone when I upgrade to 14.4.1. Other than that the phone registers properly on 14.4.1. I can provide a pjsip log as well,

Hello, I have an Asterisk 15 with PJSIP behind NAT (Amazon EC2). Now I would like to get Early Media Video working between clients in different NATed networks. The 183 signalling goes trough perfectly, but asterisk doesn't forward the Early Media RTP stream from the caller to the recipent. I have the following configuration: [6001] type = endpoint context = internal rewrite_contact = yes

OK. I think I found the issue. The key is to add rtp_symmetric=yes Here's what my final configuration looks like: [transport-udp] type=transport protocol=udp bind=0.0.0.0 ;; for within EC2 local_net=172.31.32.0/20 ;; For softphones within EC2 local_net=192.168.1.0/24 external_media_address=<publicIPOfEC2Instance> external_signaling_address=<publicIPOfEC2Instance>

I've seen this happen three times in the wild now.  I've been trying to isolate the source of the issue, but so far it seems like there's not enough debug output to know why this occurs. Long story short: - Start Asterisk - PJSIP Handles receiving INVITE from ITSP via WAN (Asterisk is behind NAT).  SIP is handled correctly, Asterisk responds OK with RTP media address of

I just noticed, the calling device isn't even sending the early media video stream. It just sends an early media audio stream. Is there propably a change in the signaling needed? (On another P2P SIP Server the early media video works.) 2018-04-10 12:29 GMT+02:00 Benjamin Marty <benjamin.marty at gmail.com>: > Hi Florian > > I already have the external_media_address set in the

Ok Dan, try this... I was able to get this to work behind a NAT and with ip address authentication. [global] type = global debug = yes [transport1] type = transport bind = 0.0.0.0 protocol = udp *local_net=<yourlocalnet I.E. 10.10.10.10/24 <http://10.10.10.10/24>>external_media_address=<your public ip address>external_signaling_address=<your public address>*

Asterisk 13.8 Is CALLERID(all) supposed to wok for pjsip? When I do this: exten => 1234,Set(CALLERID(all)="Jon Doe" <+123456789>) same => n,Dial(PJSIP/phone123, 30) I expect the callerid to be as set, but is always seems to be "phone123", the name of the endpoint. Andrew -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello. I am having a lot of problems with SIP through NAT. So, I decided to adopt PJSIP. However, I am not able to make the extensions ring when receiving a call from the queue. I'm using telnet to include the extension and on the asterisk console, it even shows Called PJSIP/6001, but the extension doesn't ring. If I call from extension to extension, it works normally. telenet:

hi, i'm fighting with webrtc for 14 days reporting my experience to minimize number of crazy asterisk users i have working webrtc with simpl5 + asterisk 13 + pjproject 2.4.5 + chan_pjsip + secure websockets + secure audio + audio in both ways problems first, i needed run chan_sip for old hard phones and wss with chan_pjsip only for webrtc. this is possible with patch from

I did a quick check between what I have set and your settings below. You can try the following and see if it helps In your endpoint: bind_rtp_to_media_address=yes With best regards Florian Floimair Innovation - Software-Development - VoIP & DevOps COMMEND INTERNATIONAL GMBH A-5020 Salzburg, Saalachstra?e 51 Tel: +43-662-85 62 25 Fax: +43-662-85 62 26 http://www.commend.com Security

Hi, I'm trying to setup snom 710 phone with asterisk 13 with PJSIP. inbound is working fine but i cannot dial out. i don't hear anything on the phone and asterisk CLI also does not show anything. my config is. please advice. [2001] type=endpoint context=out-local disallow=all allow=ulaw allow=alaw transport=system-udp auth=2001

Hello everyone, I have a Atcom AX-1600P(1) card with a FXO module and I can't configure it. I have four extension with this PJSIP settings: --- /etc/asterisk/pjsip.conf --- [transport-udp] type=transport protocol=udp bind=0.0.0.0 [6001] type=endpoint transport=transport-udp context=from-internal disallow=all allow=ulaw auth=6001 aors=6001 direct_media=no rtp_symmetric=yes force_rport=yes

On Mon, Dec 15, 2014 at 7:34 PM, Dan Cropp <dan at amtelco.com> wrote: > > I am not sure if I entered the correct settings for the transport > information. > > For the local_net, I entered my local ip address, but no mask. I will > check with the network admin so he can verify the settings I entered. > > > You need the network and mask. For example if the ip

On 1 July 2016 at 17:41, Joshua Colp <jcolp at digium.com> wrote: > > >> exten => 1234,Set(CALLERID(all)="Jon Doe" <+123456789>) >> same => n,Dial(PJSIP/phone123, 30) >> > > Your exten line has no priority, is that how it is in your dialplan? > Actually no, I stole that line from an earlier email to this list. Mine has a priority.

Hello! Oh, wise ones, ponder with me over two of the surprises that populate the universe! I have a phone, that I sometimes cannot reach, connected via pjsip. It can call other extensions just fine, it can call out over a trunk to my cell, all is well, but getting a call? Forget it most of the time. Here is all the config relevant to that phone: [murftest12] type=aor qualify_frequency=1992

I'm quite new to Asterisk and using Asterisk 13 on FreeBSD current. Asterisk is behind a NAT router, the physical setup is very much a trivial one. The Asterisk PBX is supposed to act as the telephone gateway for several VoIP/SIP phones. I'm using throughout pjsip as configuration, I have no experience with chan_sip since I started recently using Asterisk for several SoHo and lab's

Le 09/09/2016 ? 18:32, Madushan Geethanga a ?crit : > Hi, If you're not using RTP encryption did you uncheck the option in your RTP TAB from identity ? > > This is the log. ex dialling 0 from snom phone > > > <--- Received SIP request (1230 bytes) from UDP:123.231.72.210:33878 > <http://123.231.72.210:33878> ---> > INVITE sip:0 at 54.206.59.252

Hello. I am using asterisk and chan_sip a lot of years. And newbie in chan_pjsip. Now i am transfering all from chan_sip to chan_pjsip. And have a lot of questions. First of... system: Asterisk 13.2 on slackware 14.1 Errors on outgoing call: [2015-03-03 00:18:58] ERROR[6794]: chan_pjsip.c:1778 request: Failed to create outgoing session to endpoint 'srv_d228' [2015-03-03 00:18:58]