similar to: centos 5 is reporting invalid mac address

What is happening in centos 5 with network config files??? I have a machine with 2 network cards. ifcfg-eth1 keeps changing to DHCP. All my static setup is gone. Why is it doing this? How can I stop it? I run "netconfig -d eth1" and re-setup my static information. I reboot and now I am back to DHCP. I have a gigabyte motherboard, nvidia chipset. forcedeth driver. eth0 is e1000.

Me again. The ASUS P5N32-SLI motherboard in my new machine has dual NICs but CentOS has only detected one of them. I've tried rebooting with the network plugged in only to the second one, but kudzu still doesn't find it. Any suggestions?

Hello all, I got this tiny problem, I bought an Asus m2n-vm hdmi mobo two weeks ago and it seems not to be fully working under centos amd64(4.6, 4.9, 5.0, 5.1) or even redhat EL 5.0 i386, amd64, I tried to install centos and redhat EL using the linux dd and linux noprobe commands to load driver disk from nVidia guys but it doesn't detect the HD I'm using their diferent versions of the

I have a machine with 2 network cards. Installing centos 5 on it. I set up both cards with static IP addresses. activate on boot etc... One is e1000 Intel the other is onboard forcedeth (nvidia). After I reboot the forcedeth ifcfg-eth1 file is changed to DHCP. I use netconfig -d eth1 to set it back up and reboot again and the changes back to DHCP. Only thing to add here is the network card

While I wait for the Xen 3.0 Test CD to download, has anyone has luck using an Asus M2N32-SLI Deluxe motherboard (NVIDIA nForce 590 SLI MCP chipset)? The CPU is an AMD Athlon64 X2 3800+ AM2 w/ 2GB DDR2 533. The motherboard mostly works under Gentoo using kernel 2.6.18 with the "noapic" kernel boot option in my grub.conf file. The only major issue with the Gentoo kernel

I have a brand new ASUS MB model M2N-MX which is giving me issues when installing Centos 4.4 64 bit I initially had problems with finding the SATA drives but I resolved that issue by simply selecting the NVIDIA SATA (sata_nv)driver from the list of drivers during the initial install. The install seemed to go fine after that as the installer uses the Generic VESA video driver during the install,

Hello ! I installed Windows 2003 Server (RC2) sucessfully on xen 3.0.3-rc3 changeset 11732. XEN and DOM0 is 64-bit X86_64 based. The hardware I use is a Athlon 64 X2 3800+ (EE, Energy Efficient Version) on a simple ASUS M2N-MX Mainboard. However I wasn''t able to run the installation with ACPI enabled in the config file for the domain (acpi=1). The setup procedure simply freezes after

Hi all, I'm trying to troubleshoot my way thru a ACPI-issue on several machines with the Asus P5N32-E SLI motherboard (S775, Nvidia 680i chipset) http://www.asus.com/products.aspx?l1=3&l2=11&l3=397&l4=0&model=1459&modelmenu=1 This is CentOS 4 x86_64, and appears on all tested kernels, including kernel-smp-2.6.9-67.0.4.EL My symptoms are that the machine won't

Hi all, Same system as my previous mail - Asus P5N32-E SLI motherboards, CentOS 4 x86_64. The kernel-supplied forcedeth driver works in kernel-smp-2.6.9-55.0.9.EL (both with and without acpi=off), but after upgrading to kernel-smp-2.6.9-67.0.4.EL, networking does not start. After trying dhcp, ifconfig reports 17 dropped TX packets (all other counters are empty). Ethtool reports the same

What socket AM2 motherboards out there work well with xen (i.e. support > 4G ram, sata and lan chipsets work). I''m looking to probably run one of the lowpower Athlon 64 X2 4200''s in it. I''d also like to see atleast 4 ram slots. Anyone have any recomendations? Thanks, Doug _______________________________________________ Xen-users mailing list

I have two servers with identical hardware ... TYAN i3210w system boards with dual intel gigabit interfaces, and a PCI intel gigabit nic. I'm running Centos 5.4, x86_64, 2.6.18-164.6.1.el5 Every other time I reboot, the nics initialize in a different order. anaconda had setup /etc/modprobe.conf with alias lines for the cards: alias eth0 e1000 alias eth1 e1000e alias eth2 e1000e However,

Hi, today I tested kernel 2.6.33 and it seems that nouveau doesn't detect the DVI-connector of my GeForce 6150SE (Asus M2N-VM DH). The screen turns black during boot-process immediately after the "[drm] nouveau ..." messages appeared. The board has two connectors (DVI + VGA) and I'm using the DVI-connector only. Everything is fine when I use a VGA-cable instead. See boot.msg

This is my first post here, and i hope it is ok that i posted in this thread. I have been doing a bit of reading on the solaris platforms, and seem to be inclined to try out the open solaris os or solaris 10. My only worry is that my lack of knowledge with the command line may make this difficult regarding trouble shooting. It seems fairly straighforward creating zpools etc, but maybe nexenta is

So, as promised, here an first summary. Hardware: AMD Athlon64 X2-4600+ with Asus M2N-Mainboard. Just a short hint: By far not all memory modules work with the Asus boards! Make sure to have compatible ones... After 2 days of trial and error I got the following results: Debian "Sarge" x64: Doesn''t like the new nVidia SATA-Controller (will check today with PATA-interface)

What about the Asus M2N-SLI Deluxe motherboard? It has 7 SATA ports, supports ECC memory, socket AM2, generally looks very attractive for my home storage server. Except that it, and the nvidia nForce 570-SLI it''s built on, don''t seem to be on the HCL. I''m hoping that''s just "yet", not reported yet. Anybody run Solaris on it? Or at least on any

When using 4.4 to install on gigabyte GA-M51GM-S2 motherboard basically an Nforce 410/430 chipset then network is not initially detect to perform a network install. It let me attempt to manually select a driver but I do not see the driver in the list. After installing the network works and the forcedeth driver is loaded. Is there a way to get this driver detected or manually loaded? THanks,

Hi all, I had asked the other day about my new machine amd 6000+ and strangely SLOWWING down then eventually stopping. I have tried a new 500W power supply, I took out the extra video card, and just used the one on the motherboard (both are nvidia one with DVI one RGB). I took out all the RAM and tried differnent RAM. I ran memtest86 (ran fine until the machine turn off). Harddrives should be

I am using centos 5 x86_64 AMD64 X2 4200+. I am current on yum update. My machine has two ethernet cards. e1000 (eth0) and forcedeth (eth1) [root at fsdsigns2 ~]# more /etc/modprobe.conf alias eth0 e1000 alias eth1 forcedeth sometimes on boot the forcedeth driver thinks it is eth0: [root at fsdsigns2 ~]# dmesg | grep eth forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.

On 03/12/2015 10:06, Leon Fauster wrote: > Am 03.12.2015 um 10:53 schrieb Duncan Brown <centos2 at duncb.co.uk>: >> On 03/12/2015 09:40, Bernard Lheureux wrote: >>> On 12/03/2015 10:29 AM, Duncan Brown wrote: >>> initramfs is missing... >>> check if /boot/initramfs-{kernelversion}.img is correctly there, if not do a "yum reinstall

Hi, I have a wireless network but no wired network. I need to access the net for the necessary installation of the wireless drivers in CentOS 5.1. Could anyone let me know how i can go about it!! My card is Intel PRO/Wireless 3945 -------------- next part -------------- An HTML attachment was scrubbed... URL: