similar to: Help with voicemail

Hi list! I have 4 numbers on my Asterisk 1.8. 3 work perfectly, the 4.th not. I'm not sure, when it finish to work, since a month ago it runs without any problem... Well, if I will be called on this number I can't hear anything and in Asterisk I see these: [Jul 15 18:59:55] WARNING[8752]: channel.c:5060 ast_write: Codec mismatch on channel SIP/00493514977290-000001d1 setting write format

Hi, I copied a setup from an older 1.8.5 installation to an 11.15 installation, and I'm having problems getting call files to work. Here is the extension setup I'm using: [outbound-swift] exten => _[a-zA-Z].,1,Answer exten => _[a-zA-Z].,n,Playback(AAA/check_ip_failure) ;exten => _[a-zA-Z].,1,Swift("${EXTEN}") exten => _[a-zA-Z].,n,Goto(1) [mis-phone] exten =>

Hello. I have a codec problem to send calls from a SIP device to a H323 gateway. First I'll explain the scenario: - Asterisk 1.2.1 - The SIP phone can use any codec I want. - The H323 gateway can only use g729 (cause it's not under my administration) - SIP phone has g729 configured, so my asterisk doesn't need to "transcode" (I don't have licences for g729) - sip.conf

Hi All, I have this codec problem, I use "gsm" in my iax.conf file and in teliax settings also, but the error is still appearing as below. please help me. Kumara Starting simple switch on 'Zap/1-1' -- Executing Dial("Zap/1-1","IAX2/kumara@teliax/01194777070239|30|tr") in new stack -- Called kumara@teliax/01194777070239 -- Call accepted by

Hi i am trying to do the same thing: receive a call from a cisco callmanager and forward it to a SIP user. Asterisk is compiled with h323 support, and is configured as a gateway in the cisco callmanager. h323.conf: [general] port = 1720 bindaddr = 193.x.x.x ; this SHALL contain a single, valid IP address for this machine allow=all extension.conf: exten = 3298,1,Answer exten =

Hi Sir, We have integrated Skype with Asterisk (skype user id:- rexesbposolutions). Each call which is coming to skype account is getting transfered to Asterisk Queue. It has following two cases: case 1: When we call from normal skype account to skype account (rexesbposolutions), everything is working fine. case 2: This skype account (rexesbposolutions) has been assigned with a online virtual

Greetings! to all Now, with some hard time and help from many genurous people's in the list, I have come to this point with my TDM20B card & my teliax's IAX2 account. I hope someone may help me with this issue mentioned below. I have already selected my codec as gms in my iax.conf as well as in teliax's "my account page" but still i have the same error when I attempt

Hi list! I'm using Asterisk 1.8.30.0 on a OpenWRT device and it works perfectly. I configured a voicemail and I receive an E-Mail with some information about the call. Again, wonderful! Now my wish: I'd like to have Asterisk to search the caller in a list file and send me the name corresponding to the number in the E-Mail of voicemail. Is it possible? I currently use ${VM_CALLERID} in

Hi i'm trying to connect to the PSTN in the following way sip ATA -> * -> gnugk -> Cisco AS5300 -> PSTN I'm using asterisk CVS-HEAD-06/01/05-14:33:15 running over RH EL3 Asterisk-Oh323 0.7.2 pre1 Open H323 v1.13.5 pwlib v1.6.6 and I'm having a lot of trouble, gnugk and * both have public ips and are not behind any type of firewall, the sip ATA is behind a firewall and

Hi, I have just signed up with Voxee.com and have attached my Asterisk server to dial them via IAX2. Below is the start of the log which dials the number and promply hangs up when the call is answered, with the logs saying that the channel is not compatiable. I have traced this down to the g.729 codec which I don't have installed. Any ideas on how to force that the codec not be used?

Justin Killen wrote: <snip> > > Whenever I try to copy this callfile into /var/spool/asterisk/outgoing/ > I get these 3 lines repeating over and over (I?m not 100% sure which > entry is first): > > [2015-02-16 16:56:02] WARNING[9737][C-0000f8a7]: channel.c:5353 > set_format: Unable to find a codec translation path from (nothing) to (slin) > > [2015-02-16

Daniel Heckl <daniel.heckl at gmail.com> schrieb: > You are searching for ?Call Pickup?. It is implemented in Asterisk by > default. > > https://wiki.asterisk.org/wiki/display/AST/Call+Pickup > <https://wiki.asterisk.org/wiki/display/AST/Call+Pickup> Take a look under > section ?Configuration Options?. Hi, Daniel! Thanks for your answer... I'm using Asterisk

set_format: Unable to find a codec translation path from ulaw to g729 Both endpoints are PAP2 set to G711 only I have 1.2.17 on Suse 10.1

Max Grobecker <max.grobecker at ml.grobecker.info> schrieb: Hello Max, > I'm also a customer of the DTAG. > Yesterday, the messed a bit with their DNS entries... Maybe they tried again to repair a working system... :) > If you are NOT using their DNS resolvers you got a "wrong" IP address back > that was not working. Besides that, you should disable SRV lookups

Hi list! Right now I configured my Asterisk to forward the calls for the number X to both phones (mine and the phone of my wife). It works, of course, but I'm not enthusiast... I see what we have at office: if one phone rings, other phones in the same group can "catch the call", so that if a colleague is not present, another colleague can catch the call. I'd like to have the

I'm sitting here with my dunce cap on. My weak excuse is that I haven't ever played with g729 before. I have a Sipura 841. I have the phone config set to use g729. Its appropriate sip.conf entry, and the IAX stanza for my ITSP all set to disallow=all, allow=g729. But as soon as I dial, I get a complaint from the server: -- Call accepted by 66.225.202.72 (format g729) --

Hi list! Currently I use Asterisk 1.8.30.0 on an OpenWRT-Switch. Now I want to change to Asterisk 13.14.1 on a Banana PI (with Armbian/Debian 9). Well, I copied the configuration and changed what needed, so basically, it works, at least with my tests. But when Asterisk will be started, in the message log I get this error: [Feb 15 08:40:15] ERROR[3971] chan_oss.c: Unable to register channel

Hello, I am having a Mac 10.6.4 (Snow Leopard). I have compiled and built Asterisk 1.6.2.9 and Festival 2.0.95:beta on my machine. Asterisk is working fine with SIP channels without Festival. I have written following context in extension.conf: [connect-to-me] exten => s,1,Answer Exten => s,n,SayDigits(?1?) exten => s,n,Festival(hello john) exten => s,n,Hangup I use call files to

Joshua, If I'm understanding this correctly, you're saying that the Playback is failing because it isn't connected to anything on the other end, because the Dial() failed. When the channel is created on the "OutgoingSpoolFailed" extension, what context is it created in, one of the origin legs? Is there a way detect this condition in the target context ([outbound-swift]),

Hi all, I must admit that I am stuck. I have a TDM400P card with two FXS and two FXO modules which I had set up and configured so that it was working beautifully. The only problem was that occasionally it would get itself into a state where outgoing calls would simply be met with a very loud static. A reboot would fix this issue and everything would work fine for a while. Recently however,