similar to: How to diable fax header (OR: what module could add that header?)

Hello users, Recently i have installed the free version of FaxForAsterisk and trying to work with it by sending a fax on T38. My version information is as follows i)Asterisk 1.6.0.20 ii)res_fax-1.6.0.14_1.1.6-x86_32 iii)res_fax_digium-1.6.0.14_1.1.6-i686_32 sip.conf [general] t38pt_udptl=yes extensions.conf [default] exten => _XXXXXXXXXX,1,NoOp(Fax Incoming Call) exten =>

Hello, I have a question regarding incoming fax to local file (on the Asterisk server). While the fax is received properly (I have the tiff file generated as expected) I get the warning 'FAX CNG detected but no fax extension' on the consol. If the fax is received ok then what 'fax extension' does it expect and what should I do there? My Setup: Sender -> Public PSTN ->

I am testing out inbound faxing using res_fax and res_fax_spandsp.so My system answers the call but then sets there on the ReseiveFax line then comes back with an error that it exceeded the maximum retries. How would I go about debugging this? Below is my very simple dialplan code I am using, and the fax show version gives the following as well. FAX For Asterisk Components:

To provide a reliable fax solution for users connected to a Asterisk 1.6.2.6 server i have tested a few T.38 capable ATA's: - Patton M-ATA - Grandstream HandyTone 486 - Fritz!Box 7170 I have tried Asterisk 1.6.2.6 compiled with SpanDSP-0.0.6pre17 and also Asterisk 1.6.2.6 with Fax for Asterisk installed. These Asterisk servers are connected to a Cisco PGW 2200 + AS5400XM. Sending fax

Hi All, I seem to have stumbled on a bit of a problem. When trying to send a fax with Fax For Asterisk on 1.6.2.x (have tried 1.6.2.5, 1.6.2.7 and the current svn version, with FFA 1.2 I get a core dump each time. Here is an extract form the console: [May 12 22:47:09] DEBUG[22584]: app_queue.c:1084 handle_statechange: Device 'SIP/vltb-sbc01' changed to state '1' (Not in use)

Hello. I've been trying to setup Free Fax for Asterisk on a Debian machine with Asterisk 1.8. I have managed to register and installed the Digium modules. Sending and receiving through it have resulted in failure. The output of fax show capabilities is: Registered FAX Technology Modules: Type : DIGIUM Description : Digium FAX Driver Capabilities : SEND

Hi everybody, I've installed Free Fax For Asterisk in my Asterisk box but I don't understand how it works as when using SendFax application from dialplan, I can't find how to introduce destination fax number. How this application works? Do I have to call destination fax using Dial application, detect somehow that it's a fax and then use SendFAX application specifying FAXOPTs and

Hi, I am using asterisk 11.8 in combination with spandsp to send and receive T38 Faxes. All works fine, but I do not know how to get the remoteheader from the fax I receive. When I send a fax, there are Faxopts to set the localstationid and the headerinfo, but for receiving, there seems to only exist the Faxopts remotestationid but for sure on any fax I receive there is a remoteheaderinfo

Hi, thanks for your answer. Unfortunately this is, what I already know. I was wondering, why it is possible to set ID and Header for an outgoing fax (which will then in turn be inserted via asterisk on top of the transferred "image") , while it seems to not be possible to get the Header from a received fax (only the id), although it is present in the faxdocument. The ID is also

Hi Guys, i am using the latest version of asterisk 1.4 (1.4.33.1), dahdi (2.3.0.1) and FFA (Applications: 1.4_1.2.0, Digium FAX Driver: 1.4_1.2.0). the issue i'm having is that i'm able to receive faxes from a website (that offer this service) but not able to receive from a regular fax machine (that is working perfect). [fax-rx] exten => receive,1,NoOp(**** FAX RECEIVE ****) exten

Hello, I have Asterisk 1.6.1.12 with FAX For Asterisk Components: Applications: 1.6.1.5_1.1.6 Digium FAX Driver: 1.6.1.5_1.1.6 (optimized for core2_32) If I use call file with spool -------------------------------------------- Channel: SIP/IP/DEst No MaxRetries: 0 RetryTime: 10 WaitTime: 50 Application:SendFAX Data:/var/spool/asterisk/test.tif

Hi, Do you have any example showing how to use SendFAX ? I can see several examples of ReceiveFAX but not a single one showing SendFAX. Regards -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20081127/b41ca08b/attachment.htm

Hi all, I am running to the following problem, when using the below dialplan to receive fax, everything works perfect till this line exten => receive,n,ReceiveFAX(${FAXFILE}): and then the following line cannot be executed, it's like asterisk can't go back to dialplan and continue, the good news is when i check what is received in my fax folder i find that the file is a valid one (not

Is it possible to force T38 for all invocations ReceiveFAX() ? Receiving fax always worked OK on Callweaver though I could put SipT38Switchover() into the dial plan. I can't with Digium fax, and it always fails at the point it decides to switch to T38.

I am working on some fax tools for some of my users. I am reading the https://wiki.asterisk.org docs for faxing. Is see Application_SendFax and Application_SendeFax has one been discondinued? Any feed back on using the res_fax module would be apperciated. Any examples or other. Thanks Bryant -------------- next part -------------- An HTML attachment was scrubbed... URL:

I am testing Fax for Asterisk. But, I meet a problem. I try to Send a Fax (.tiff) from the first asterisk (Asterisk1) to the second asterisk (Asterisk2). Asterisk1 initiates an INVITE with audio G.711. Asterisk2 accepts this INVITE. Immediately, Asterisk2 sends an re-INVITE with T.38 to Asterisk1. But, Asterisk1 responds with "488 not acceptable here". I double check t38pt_udptl = yes in

Hi, Last night I was working on trying to get Fax for Asterisk installed. I followed all the instructions, but noted that the download selector only provider an X86 32 Bit binary. The machine I'm using is: 2.6.26-1-amd64 #1 SMP Fri Mar 13 17:46:45 UTC 2009 x86_64 GNU/Linux Consequently, on load it presents an error: [Sep 12 10:25:35] WARNING[31306]: loader.c:368 load_dynamic_module:

I have res_fax setup and working for the most part. However, I'm seeing some fax machines drop the connection on me - Apr 9 17:33:11] NOTICE[30809]: res_fax.c:906 generic_fax_exec: Channel 'DAHDI/1-1' did not return a frame; probably hung up. -- Channel 0/1, span 1 got hangup, cause 102 -- Channel 'DAHDI/1-1' FAX session '20' is complete, result:

Hello, I'm having difficulties to make Asterisk (1.6.0.6) interoperate correctly with a CISCO mediaGW in order to send faxes to the PSTN using T.38. When Asterisk sends the initial INVITE containing the T.38 media offer in the SDP, the CISCO answers with a 488 Not Acceptable Media. Apparently, it looks like a configuration problem in the CISCO, but I have tested the CISCO with the Zoiper

Morning, Have some questions regarding receiving and sending faxes... 1:st example: exten => 101,1,Answer() exten => 101,2,Wait(3) exten => 101,3,ReceiveFAX(/var/spool/asterisk/tmp/fax.tiff) exten => 101,4,System(tiff2pdf -p A4 /var/spool/asterisk/tmp/fax.tiff > /var/spool/asterisk/tmp/fax.pdf) exten => 101,5,System(mutt -s 'New FAX for you sir' -a