similar to: does chan dahdi supports fax?

Calls that come in on DAHDI FXO ports are routed to [context], extension 's' INSTEAD, I would like to route specific ports to specific extensions, For example: I want DAHDI/1-1 to go to 1234 I want DAHDI/1-2 to go to 2345 I want DAHDI/1-3 to go to 3456 ...etc What is the CLEANEST way to do this? Yes, I can create a private context for each DAHDI channel but that seems messy and

Hello list i have an issue with my dahdi_channels.conf in span 1 when i use it like below i can do my outband calls without issue ; Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER) group=0,11 context=from-pstn switchtype = euroisdn signalling = pri_cpe channel => 17-31 context = default group = 63 but when i add in channel 1-15 like: channel => 1-15,17-31 i receive all

Hi, Built a new server at the weekend and install Asterisk 1.6.0.9 and IAX and SIP work great :) The one problem I am having is getting the OpenVox (TDM400 type card) to work. It is successfully identified using WCTDM kernel module and dahdi_scan picks it up just fine. The issue is when I try and setup dahdi_channel.conf as it fails everytime. When running asterisk -rvvvv I see the port pick

I've got a Digium Wildcard TDM410P with one POTS line and three extensions. One of the extensions is connected to a fax modem. This kind of works, but there's a gotcha. If I set faxdetect=incoming in chan_dahdi.conf, then incoming faxes do get routed to the modem and this all works, but outbound faxes fail, with a message like this: [Oct 29 21:57:09] WARNING[16732][C-00000000] app_dial.c:

Hi folks, I was hoping that someone might be able to help clarify some confusion I have on DAHDI Fax detection after spending some time searching. My understanding is this: 1.) Echo cancellation is automatically disabled upon recognition of a CNG tone, regardless of the faxdetect setting. This can only be disabled at compile time. 2.) faxdetect=incoming will, upon detection of a CNG tone,

We've been having some problems with an E1 PRI line for a few days. We get the following errors: [Mar 24 10:13:39] ERROR[22009] chan_dahdi.c: PRI Span: 2 ROSE REJECT: [Mar 24 10:13:39] ERROR[22009] chan_dahdi.c: PRI Span: 2 INVOKE ID: 316 [Mar 24 10:13:39] ERROR[22009] chan_dahdi.c: PRI Span: 2 PROBLEM: Invoke: Unrecognized Operation The telephone company says that

Asterisk 16 latest DAHDI 3.0.0 latest Excerpt from chan_dahdi.conf is shown below. I'm trying to enable fax detection on inbound calls so that I can take appropriate action in the dial plan. "dahdi show channel 1" shows "Fax Handled: no". Does that mean that I don't have it configured correctly? [channels] ; Span 1: WCTE2/0/1 "WCTE23X (PCI) Card 0 Span

PRI debug of the entire call would be great, also, switchtype would be awesome as well. Thanks! Matthew Fredrickson On Thu, Mar 24, 2016 at 4:07 PM, Carlos Rojas <crt.rojas at gmail.com> wrote: > Hi > > Did you activate the pri debug on the cli asterisk? > > On Thu, Mar 24, 2016 at 12:59 PM, Carlos Chavez <cursor at telecomabmex.com> > wrote: >> >>

I am running Asterisk 1.6.2.17.2 with a Openvox A400 card with 2FXO/2FXS modules. I'm trying to set-up things to route analog fax calls from a FXO port to an analog fax machine on a FXS port on the same card. Outgoing faxes work just fine. But incoming faces are routed to the right DAHDI extension, but the call dropped right as the fax machine rings for the first time. The fax machine

I'm trying to get "blind transfer" from an incoming DAHDI line to an external number to work on an * 1.6 install using a T1 from XO. The documentation is very "distributed" and incomplete, so while it's not working, it's definitely more likely my error somehow. Couple questions if anybody is out there who even knows what TBCT is. 1) Is this even

Hi all, I wanted to switch from my current setup (mISDN) to the native dahdi with b410p support (wcb4xp). All works fine for normal phone calls but not for faxing. Faxes are distorted, if arriving at all, and hylafax logs the usual bad stuff (HDLC frame not byte-oriented.) Our setup uses a digium b410p card with asterisk 1.6, latest libpri and dahdi, hylafax with iaxmodem, and all this on 1

[18884732963 at from-fax-machine:... - your call is hitting the from-fax-machine context - yet your 'fax' exten is in the from-pstn-4 context. See the "[2011-03-17 13:40:29.6] NOTICE[8825] chan_dahdi.c: Fax detected, but no fax extension" line. When Asterisk detects an incoming fax tone - it tries to automagically route the call to the 'fax' extension in the SAME

OK, after my last message about fax detection, I feel a bit better informed and able to press forward. I started looking into this because I was getting lots of false positive fax detection errors in the logs with faxdetect=both set in chan_dahdi.conf. Anyhow, I do not currently use fax detection, and we have a dedicated Fax DID on our PRI, so setting faxdetect=no works fine. Having said that, I

The card you installed has FXO or FXS modules in it ????? are you getting your lines directly from the telco co??? Doug D On Mon 23/08/10 8:37 AM , Cassius Smith cassius at cassius.org sent: * -----Original Message----- * From: Todd Reese * Reply-to: Asterisk Users Mailing List - Non-Commercial Discussion * To: asterisk-users at lists.digium.com [3] * Subject: [asterisk-users] Dahdi

Becasue of all the issues with fax over voip, we want to use pstn for our fax machine, but not dedicate a line just to fax. I'm thinking of having asterisk answer the pstn line, check for fax tones, and route appropriately. In zapata ( chan_dahdi ) set faxdetect=incoming then the dial plan would have [incoming-pstn] exten => fax,1,Dial(DAHDI/1) ; the fax machine exten =>

the Telco, I can make calls in. What I am trying to get though is how to pass through the DID range. The E1 that I am connecting to the Telco with, used to connect direct to the NEC system and already has hunt group calling enabled for all 30 channels. Also, I was given a 100 number indial range (from 00 -> 99). If the E1 is connected to the NEC directly, I can call 5555 7320 and the NEC

I'm running an AsteriskNow V1.7.1 with both a PSTN connection and fax machine. Both are connected to a DAHDI board. I'd like to route incoming PSTN fax calls to the extension of the fax machine and process non-fax calls through different dialplan.logic. What's the best way to go about doing this? I've looked into Fax for Asterisk, bit I'm not sure that I want it or NVFax

Hello, I was wondering if the following was possible: When somebody sends a fax to my direct number 0101234567105 (my extension will be 105) is it possible that Asterisk, or an addon sees this as a fax, and e-mail the fax to me? So everybody with a private extension will be able to receive faxes in his e-mailbox on his direct number. Any pointers would be highly appreciated! Thanks, Peter

I've got a single TDM 400P board with two internal ports and 1 external. chan_dahdi.conf: context=internal ; Uses the [internal] context in extensions.conf signalling=fxo_ks ; fxo_ks not auto Use FXO signalling for FXS group=0 channel => 1 ; Telephone attached to port 1 channel => 2 ; Telephone attached to port 2 context=incoming-pstn-line ; Incoming calls

Hello List, it is a very long time since I wrote here.... It has been still in Zaptel times.... Today I am run into a related problem: I can't get a DAHDI setup to work 100%. I am configuring an Astribank XR00013 (BRI, two ISDN ports). At some degree the installation (latest DAHDI drivers, Asterisk 1.6.0.18 on Centos 5.x) works. I can get incoming calls to the dialplan context that is