similar to: Multicast to polycom from asterisk

> I am using 11.17.0 - and MulticastRTP. Doesnt seem to work with > polycom phones as other devices receive my multicast just fine. > > Is there something special to do to get multicast working with polycom phones? > (other than enable multicast on the actual phone). Didn't see if anyone had answered you or not on this, but Polycom uses their own form of MulticastRTP. It

I'm currently working with Asterisk 11.8.1 trying to get Multicast RTP working (it's not) with some Polycom phones, and I'm really trying to determine if Asterisk or the phones are the issue. I THINK it's Asterisk... In extensions.conf I have a simple: "Page(MulticastRTP/basic/x.x.x.x:xxxx) line, and when I dial that extension I get: -- Called

Greetings everyone, I was wondering if there was a way to change the codec that Asterisk uses when streaming via MulticastRTP. Or perhaps a way to transcode the multicast stream. In the CLI, when I have a multicast stream in progress, I am typing 'core show channel MulticastRTP/0x7f7........' to get lots of helpful information. I have noticed that when I do a MULTICAST page and send data

Hi all, Has anyone made up custom ring tones for the Polycom SIP phones? We use different rings for different lines, but the ones it comes with are all very similar. In the interesting of sharing, here's one I made up for paging: <PAGE_BEEP se.pat.ringer.13.name="Page Beep" se.pat.ringer.13.inst.1.type="chord" se.pat.ringer.13.inst.1.value="12"

I am using a cyberdata "sip paging adapter" and with the Dial(MulticastRTP/basic/IP:port) and with tshark I see the RTP data, my device looks like its accepting the data and I hear a click for my relay on my device so it would seem its accepting the call, however - I hear no audio... Asterisk 11.11.0 is what I am using. What might be wrong here? Thanks, jerry -------------- next part

Hi everyone, I am sending out a multicast page using the following in my dialplan: Page(MulticastRTP/linksys/${MULTICAST_IP_ADDR}:6061/${MULTICAST_IP_ADDR}:6061,q) Everything works great, but I had a question about SIP and SDP: Should I be seeing a SIP/SDP message from the asterisk server containing media information and the multicast IP address? On wireshark, I see SIP/SDP from the admin

On Mon, 13 Apr 2015, Kevin Larsen wrote: > I hesitate to promote the name here since this is non-commercial > discussion... > but Polycom... > Polycom phones... If mentioning Polycom is OK, I think mentioning a possible commercial solution is OK. -- Thanks in advance, ------------------------------------------------------------------------- Steve Edwards sedwards at

In ipmid.cfg I have: <G3INTERCOM se.rt.10.name="G3INTERCOM" se.rt.4.type="ring-answer" se.rt.4.timeout="1000" se.rt.10.ringer="7"/> In sip.cfg I have: <alertInfo voIpProt.SIP.alertInfo.1.value="G3INTERCOM" voIpProt.SIP.alertInfo.1.class="10"/> I set up a test extension: exten =>

Could not find your post for 4 months ago. -------------- Original message -------------- From: "Anton Krall" <akrall-lists@intruder.com.mx> > Yes, check a post that I made about 4 months ago, I posted the cofig for > setting the speaker, handset and ring volumes .. > > |-----Original Message----- > |From: asterisk-users-bounces@lists.digium.com >

I am looking for clues on how to configure distinctive ring for a PolyCom SoundPoint 300. Does ALERT_INFO apply? If so, how? Thanks, David Koski david.nospham@kosmosisland.com

I'm building a paging system composed of roughly 10 switches in daisy chain, with an embedded box with a speaker and a microphone for each switch. The embedded box runs my software. I need the system to be resilient to any network partition, so that anyone can send announces from any mic to all the reachable clients. I'd need also to page a subset of all the speakers. I'm

I just got a Polycom soundpoint and I set it up using the phone and web based admin. I cant seem to figure out the config files and they are confusing me greatly and I dont have time for it :) Some things are odd, like on every reboot it seems the volume I set is reset? is there any way to fix that. And the ringer seems low. - Even all the way up Anyone willing to point out a good asterisk

CVS Head from 07/07/2005 I'm trying to make an IP-501 auto answer a call. exten => 301,1,SetVar(_ALERT_INFO="Ring_Ans") exten => 301,2,SetVar(ALERT_INFO="Ring_Ans") # Tried both combinations exten => 301,3,Dial(SIP/5001,15) exten => 301,4,Hangup Sip.cfg for Polycom phone <alertInfo voIpProt.SIP.alertInfo.2.value="Ring_Ans"

I was trying to get my polycom phone to auto answer. I added this to the dialplan. Used a different phone to call "22" and the phone rang it did not auto answer. Did I miss something? exten => 22,1,SipAddHeader(Call-Info:=\;answer-after=0) exten => 22,n,SipAddHeader(Alert-Info: Ring Answer) exten => 22,n,Set(__SIPADDHEADER=Call-Info:\;answer-after=0) exten =>

Hi all - This isn't really directly Asterisk related, but has anyone successfully set up a Polycom phone to register two lines on two different Asterisk boxes? I can get the first line to register, but the second one does not. I can still place calls from that second line, which indicates to me the server, user, and secret are correct. I'm running the newest 2.6 series firmware with the

Hi We have polycom 430,501 and 301 phones. Our customer does not need DND feature in any form. I can disable this feature from asterisk server but How can i disable this feature on phones. In the sip configuration file i found the parameter that change the phone behaviour during DND from busy to normal but still if the phone is in dnd mode the phone ringer would be off which is unacceptable.

Anyone have some recommended equipment for alerting people to calls in a noisy environment? I have Polycom IP550 phones set up in some really noisy environments - our mine hoists - and they tend to drown out the ringers. I'm using Clarity WR100s now. They're analog devices, attached to Linksys PAP2T ATAs as part of a call group to get a loud (advertised as 95dB) ring out there, but it

Hi Andrew - > I have a need to be able to identify incoming calls based on some factor > (could be time of day, caller ID, dialed number, it doesn't matter.) -- > Assuming Asterisk can differentiate between the calls I want, how do I inform > the IP501? There are "only" three line appearances -- I can't simply just > ring a different appearance since there

Working on a paging system for one of my sites and running into something I can't believe is this hard. In one of the zones, they want to have three different extensions ring over the pa system, using it as a loud ringer. Now the paging system does have a loud ringer built in and I can easily have it do a simultaneous ring, but all of the extensions will sound the same over the loud

Hi, I'm having trouble setting the ringtone on my Polycom 501. The relevant entry in extensions.conf is: exten => 801,hint,SIP/creative1 exten => 801,1,SetVar(ALERT_INFO="Test") exten => 801,2,Dial(SIP/creative1,20,Ttr) In the sip.cfg: <alertInfo voIpProt.SIP.alertInfo.1.value="Test" voIpProt.SIP.alertInfo.1.class="13"/> and <TEST