similar to: IAX port

Hi I've 3 iax connections to my provider , each of them have own DID , PH1<----| | \/ PH2<-->|-----| <---------------------------> |----|<-- DID1 | A1 | <---------------------------> |ISP |<-- DID2 PH3<-->|-----| <---------------------------> |----|<-- DID3 I had iax phone on each of this connection , but now I want to terminate all

This may not strictly be an asterisk question, but not sure where else to post ... I have an Asterisk test server setup with two firefly clients, one on the local lan and one on an external ip address. Both clients are setup the same way and voice calls work fine. The asterisk console reports a "Registered" message for the external client at about one minute intervals but the

I received this before, and it is because you are using the wrong context in the iax.conf. For example: The context must match the username in the register statement. Iax.conf... register => username:secret@iax.host.net [username] type=friend context=iax-in user=username secret=secret auth=plaintext host=iax.hust.net ----------------------------------------------------------------

Hallo Did you allow udp outgoing on 4569 as well.. i found udp bit different than tcp when comming to firewalls liaan ----- Original Message ----- From: "Bartosz Wegrzyn - asterisk" <junk@lexon.ws> To: <timebandit001@gmail.com>; "Asterisk Users Mailing List - Non-Commercial Discussion" <asterisk-users@lists.digium.com> Sent: Monday, February 21, 2005 12:29

What settings are people using? I've seen the ones from dslreports but I'm in that lucky group of people that paid the 1 euro just to have it no longer work. Even after I setup a additional account over the weekend it still doesn't work. And, of course, etherreal only shows encrypted traffic so I can't snag any config settings from it. Any assistance? -----Original

i have 2 asterisk servers one on CentOS and one on Fedora , i configured IAX trunking between the 2 servers so that i dial -say from a sip extension 2000 on fedora server to a sip extension 3000 on CentOS server the call seems to be established but hangup automatically after very short time and here is the iax2 set debug command result on centos server and also my iax.conf and extension.conf and

On 10 Feb 2015, at 12:22, Jose Flores Galicia wrote: > 2015-02-09 14:36 GMT-06:00 jg <webaccounts173 at jgoettgens.de>: >> Hi! >> >> Sometimes IAX peers are not reachable and with "iax2 set debug on" I >> get >> something like this >> >> Tx-Frame Retry[ No] -- OSeqno: 000 ISeqno: 001 Type: IAX Subclass: >> PONG >>

Hi, I'm trying to track down why I'm getting calls dropped on an infrequent basis between two asterisk servers which are at the same physical location and connected to each other with UTP ethernet. Here is the connection diagram Asterisk Server 1 ===UTPENET== Switch ====UTPENET==== Asterisk Server 2 I see sporadic RX and TX frame retries when I enable iax2 debugging on either box.

hi, I use IAX softphone with asterisk and I notice that a call between two IAX softphones end after 1 min. Then I can't hear anything but the call still in progress. I have this log in asterisk IAX debug: Rx-Frame Retry[No] -- OSeqno: 002 ISeqno: 002 Type: IAX Subclass: ACK Timestamp: 00016ms SCall: 21589 DCall: 00001 [192.168.1.22:4569] Tx-Frame Retry[000] --

Hi All, I am using Asterisk 1.4.26.2 and I am getting the following problem making connections to this server. My other servers are Version 1.2.x which have no problems and this 1.4.26.2 server can call the other 1.2.x servers. The error is: chan_iax2.c:4251 handle_call_token: Call rejected, CallToken Support required. If unexpected, resolve by placing address 192.168.25.250 in the

On the asterisk1 I got this: register => username:secret@ipaddress2 [eop] username=username secret=secret type=peer host=ipaddress1 auth=md5 on the second box I got this this host is ipaddress2 [incommingiax2] username=username type=user secret=secret host=dynamic context=from-internal-custom auth=md5 on first host 1 am getting: Jun 22 14:42:10 NOTICE[2398]: chan_iax2.c:7411

Hopefully this is really a generic question about IAX and doesn't turn out to be something specific to Teliax, because they haven't been too helpful so far. All they can tell me is that my login shows "status unknown" on their end, which prevents me from receiving inbound calls on my Teliax number. Outbound calls through the same server work fine, which rules out most networking

Hi, I have two asterisk servers one is connected to the PSTN and the other one is connected to SIP users. The two servers connect with each other using IAX. When I have an incoming call from PSTN to the asterisk servers and have a forward to go back out to the PSTN the two IAX channel bridge together. Now every time I dial a DTMF digit, the asterisk is sending two DTMF digits. I enable

I have been having problems getting PrivacyManager to work correctly. Right now I am running the 1/21/05 CVS but I have been unable to get this to work on asterisk-stable either. You can see from the debug below that the inbound call is arriving via IAX2 and both the CALLING NUMBER and CALLING NAME are both set as "Unavailable". However, PrivacyManager executes and determines that

Hi everyone, THis is my second thread regarding the issue.(before I was having problems with accessing my email, which slow down my responses, sorry for that) My setup looks like this Firewall | | Asterisk---Asterisk (two asterisk servers with the same setup for high avail) | | phones Ports 5060, 10000-20000, 4569, 5036 are forwared to 192.168.1.251 which is virtual ip address on one of the

G'Day, I have a bit of FireFly problem that hopefully someone has seen before. What happens is if I make to or receive a call from the FireFly network the call will connect successfully. However, around 10 seconds after I answer the call I am disconnected. The weird thing is same thing happens if I make a call. I've had a look at the * console and I can't see that my * PBX drops

I have a PSTN termination provider "foo" which will accept standard U.S. calls in the form 1<10 digit ph#>. I have an outbound route named "foo", with dial pattern "5|.", with the only entry in trunk sequence being "IAX2/foo". I have an X-lite local extension, on which I can dial 51<10 digit ph#>, and asterisk will call out over foo and the

I'm starting to get this to work! Well I got Voice Mail to work! All calls goes to voice mail without ringing the users phone (iaxComm). Here is my iax.conf and my extensions.conf Any help would be great!! Thanks -------------- next part -------------- A non-text attachment was scrubbed... Name: extensions.conf Type: application/octet-stream Size: 1039 bytes Desc: extensions.conf Url :

hi, i want to call PC2PC between to IAX client without authentication i want to allow every user to use PC2PC no any password required. Please let me know what i have need to do in IAX.conf or any other file to allow any user to call Pc2Pc. My IAX.conf [guest] type=user context=default callerid="Guest IAX User" My extensions.conf [default]

Hi, I created an iaxtel account, and was given a password containing an "@" character. The directory pages imply that they change the web login password only. How do I reset my IAX password so that it is usable in the iax.conf file? Thanks, Steve