similar to: Cyberpower Value1200E might not need 0.667 battery scaling

On Aug 7, 2014, at 10:52 PM, Charles Lepple <clepple at gmail.com> wrote: > On Aug 7, 2014, at 10:18 PM, Matthew Stapleton <matthew4196 at gmail.com> wrote: > >> I just got a Cyberpower SOHO Value 1200 ELCD UPS and even with nut 2.7.2, it appears to report battery voltage too low due to the battery scaling function (In drivers/cps-hid.c). Even though the ups has usb id:

On Aug 7, 2014, at 10:18 PM, Matthew Stapleton <matthew4196 at gmail.com> wrote: > I just got a Cyberpower SOHO Value 1200 ELCD UPS and even with nut 2.7.2, it appears to report battery voltage too low due to the battery scaling function (In drivers/cps-hid.c). Even though the ups has usb id: 0764:0501, UPS.PowerSummary.Voltage reports 26.6 for the 24V batteries so when the 0.667

On Aug 8, 2014, at 9:15 AM, Charles Lepple <clepple at gmail.com> wrote: > On Aug 7, 2014, at 10:52 PM, Charles Lepple <clepple at gmail.com> wrote: > >> On Aug 7, 2014, at 10:18 PM, Matthew Stapleton <matthew4196 at gmail.com> wrote: >> >>> I just got a Cyberpower SOHO Value 1200 ELCD UPS and even with nut 2.7.2, it appears to report battery voltage

Attached is the first 32 seconds of the driver output after applying the patch which fixes the battery scaling problem for this UPS. Matthew Stapleton Email: matthew4196 at gmail.com On 10/08/14 01:27, Charles Lepple wrote: > On Aug 8, 2014, at 9:15 AM, Charles Lepple <clepple at gmail.com> wrote: > >> On Aug 7, 2014, at 10:52 PM, Charles Lepple <clepple at gmail.com>

On 10 August 2014 09:05, Charles Lepple <clepple at gmail.com> wrote: > On Aug 7, 2014, at 7:57 AM, Leith Bade <leith at leithalweapon.geek.nz> wrote: > > Error -32 is EPIPE, which means that the PC didn't see a reply from the device during the descriptor read. I don't know that we have ever successfully run one of these issues to ground. > Considering Eaton do

I was getting: "Can't claim USB device [0764:0501]: could not detach kernel driver from interface 0: Operation not permitted" so I manually installed the udev rules the source (I installed the Gentoo ebuild). I am now getting: # upsdrvctl start Network UPS Tools - UPS driver controller 2.4.3 Network UPS Tools - Generic HID driver 0.34 (2.4.3) USB communication driver 0.31 Using

Hi All, I bought a USB Bluetooth dongle. However, it's not working for me. Please help, how to debug and get more information as I can not see any error or warning message from system log message. I checked http://thread.gmane.org/gmane.linux.bluez.kernel/22183/focus=22211, however, also find another page

Hello list, ? ?Cannot make Evolution 850 to be recognized, maybe the problem is "Warning: incomplete endpoint descriptor" in lsusb? Details are as follows. NUT installed by download of debian package. Any ideas/suggestions are highly welcome, thanks in advance! --ValenteM = ? ?= ? ? = ? ? = Ubuntu server 12.04.1 LTS (GNU/Linux 3.2.0-35-generic x86_64) sudo dpkg -i

Hi, just try the Unitek Self Protek Mistral 1000ipF with nut and I doesn't work. How can I correctly configure it (if the driver support it). Best regards, In my dmesg: [42953293.620000] usb 1-2: new low speed USB device using uhci_hcd and address 7 [42953293.760000] usb 1-2: no configurations [42953293.760000] usb 1-2: can't read configurations, error -22 [42953293.880000] usb 1-2: new

Hi, I have a powermust with a usb connector. I searched the archive and found this post: http://lists.alioth.debian.org/pipermail/nut-upsdev/2006-April/000816.html Must I abandon hope of controlling this UPS via USB with NUT? Added this line to /etc/udev/rules.d/70-nut-usbups.rules: # OMRON - usbhid-ups SYSFS{idVendor}=="06da", SYSFS{idProduct}=="0003",

Hello I have two completely different UPS that turn out to use the same driver. Both work with blazer_usb my LSUSB says: Bus 001 Device 005: ID 0665:5161 Cypress Semiconductor USB to Serial Bus 001 Device 004: ID 0665:5161 Cypress Semiconductor USB to Serial my lsusb -vd 0665: says: pi at elektra:~ $ lsusb -vd 0665: Bus 001 Device 005: ID 0665:5161 Cypress Semiconductor USB to Serial

Hi all! FYI, after some research in your list I think that blazer_usb is the best driver for my Soyntec Sekury A600 UPS (which is not in the hardware supported lists). I connected it with my system using USB port (it also has serial RS-232) This is the report I have: battery.voltage: 13.60 battery.voltage.nominal: 12.0 beeper.status: enabled device.type: ups driver.name: blazer_usb

folks, the following is lsusb -v for my 250gb usb hard drive. I note the Protocol line mentions zip: ie bInterfaceProtocol 80 Bulk (Zip) does that mean its one of those USB-ZIP devices ? If so, to the parameters below say anything about the CHS settings needed ? tia, PS - HPA, you were correct wrt what I missed :-} Bus 001 Device 002: ID 1058:0401 Western Digital Technologies,

Hi everybody, In a christmas sequel I've been offered one of the units mentioned above. I've tried to connect it to my Fedora 8 workstation but rapidly concluded it's not yet supported by NUT. So far, I've decompiled the Java classes of the manufacturer's application and noticed that it's most probably yet another kind of serial protocol through the USB. Since

Hi Rok, I retired from working on NUT a few months ago, so I don't have the most up-to-date info. But the guys on the nut-upsdev mailing list (cc'd above) are very helpful. Both of your devices (or nearly identical ones) have been seen on the mailing lists before. The Sweex was first mentioned in a message by Eli Wapniarski on 14 Jun 2006 on nut-upsuser, and was most recently discussed

Hello, I (now) own an Emerson Liebert GXT3 6000VA conected via USB. I've searched the web trying to configure nut (nut-2.6.5-1.el6.x86_64 epel rpm on CentOS 6.3) to monitor the UPS, but couldn't find a successful configuration. I'm running kernel 2.6.32-279.14.1.el6.x86_64. The UPS is connected with an USB cable: Bus 004 Device 002: ID 10af:0008 Liebert Corp. PowerSure Interactive

Hi, we bought two Smart-UPS X 1500 FW:UPS 09.1 / ID=20 lsusb -v: Bus 002 Device 002: ID 051d:0003 American Power Conversion UPS Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor

Hi, we bought two Smart-UPS X 1500 FW:UPS 09.1 / ID=20 lsusb -v: Bus 002 Device 002: ID 051d:0003 American Power Conversion UPS Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor

Some of my messages never went through since I hit a message size limit. I'm resending them in the hopes they are under the limit. Charles, The lsusb command did not trigger a disconnect. The output of that command is below. I ran "usbhid-ups -a upsunit -DDD &> output.log" and I have attached the /var/log/messages and output.log to this email. Before running this test

rtd at linux-5048:~> lsusb -vvv -d 2a37: Bus 001 Device 005: ID 2a37:5110 Couldn't open device, some information will be missing Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 8 idVendor