similar to: Tripp Lite SMART3000RM2U (protocol 3003) running time and charge?

On May 15, 2014, at 9:39 PM, Stefan Bruda wrote: > What bugs be though is that I cannot seem to be able to read the > remaining run time on battery. The battery charge is also widely > inaccurate (it drops to zero really fast and stays there). I read > somewhere that the usb.debug numbers may hold the key to this (at > least to the running time that is), but I don't know what

Hello, First of all thank you so much for the information. At 22:43 -0400 on 2014-5-15 Charles Lepple wrote: > > On May 15, 2014, at 9:39 PM, Stefan Bruda wrote: > > > What bugs be though is that I cannot seem to be able to read the > > remaining run time on battery. The battery charge is also widely > > inaccurate (it drops to zero really fast and stays

On May 19, 2014, at 7:12 PM, Stefan Bruda wrote: > Hello, > > First of all thank you so much for the information. No problem, glad it is useful. > [...] > Therefore as far as my UPS is concerned s_value[5] is wildly > incorrect. So it turns out that the RM15002U also does not report anything useful for s_value[5]:

Hello, At 22:19 -0400 on 2014-5-19 Charles Lepple wrote: > > On May 19, 2014, at 7:12 PM, Stefan Bruda wrote: > > > Therefore as far as my UPS is concerned s_value[5] is wildly > > incorrect. > > So it turns out that the RM15002U also does not report anything useful for s_value[5]: > >

On May 22, 2014, at 10:03 AM, Stefan Bruda wrote: >> >> Does battery_voltage_nominal get set correctly? Theoretically, it >> should be 48, since the 2nd and 3rd digits of ups.debug.V are 08, >> and that gets multiplied by 6. > > Yes, as it appear as 48V in the output of upsc. Good. > >> Might be useful to have an intermediate value that doesn't scale

On May 24, 2014, at 5:49 PM, Stefan Bruda wrote: >> Don't worry about the battery physical properties for now - the >> problem there is that we don't have enough information from the UPS >> to do a proper calculation. With the V_interval[] settings, you can >> tweak the new state-of-charge calculation to match what you see via >> upsc when the battery is

Hello, At 09:24 -0400 on 2014-5-23 Charles Lepple wrote: > > See attached. Still doesn't have the writable V_interval values, > but I probably won't have time to test that until later. Thank you for the patch. > Don't worry about the battery physical properties for now - the > problem there is that we don't have enough information from the UPS > to do a

Hello, At 15:42 -0400 on 2014-6-1 Charles Lepple wrote: > > On May 24, 2014, at 5:49 PM, Stefan Bruda wrote: > > >> Don't worry about the battery physical properties for now - the > >> problem there is that we don't have enough information from the UPS > >> to do a proper calculation. With the V_interval[] settings, you can > >> tweak

On Jun 2, 2014, at 10:25 PM, Stefan Bruda wrote: > Hello, > > At 15:42 -0400 on 2014-6-1 Charles Lepple wrote: >> >> On May 24, 2014, at 5:49 PM, Stefan Bruda wrote: >> >>>> Don't worry about the battery physical properties for now - the >>>> problem there is that we don't have enough information from the UPS >>>> to do a

I'm trying to set up a single host to monitor the state of several UPS in my data center. I have a mix of several APC and Tripp-Lite in production. The former are great, the latter are not so much. With the APCs (using usbhid-ups), I can set up configs for each based on the value they report from ups.serial. With the Tripp-Lites (using tripplite_usb), there is no value returned for

I have added preliminary support for the TrippLite protocol number 2001 into tripplite_usb.c. The attached file is supplied as a patch against today's SVN. This patch adds support for TrippLite SMART550USB and some Omni models. Tested are On Line, On Battery, Battery Good, and Battery Bad indication. Everything else seems to work, but this UPS is attached to a critical system, and I can

Has anyone gotten this model of tripp-lite to work? sudo /usr/local/bin/upsdrvctl -DDDDD -u root start Network UPS Tools - UPS driver controller 2.0.5 Starting UPS: tripplite exec: /usr/local/bin/tripplite_usb -a tripplite Network UPS Tools - Tripp Lite OMNIVS and SMARTPRO driver 0.7 (2.0.5) Warning: This is an experimental driver. Some features may not function correctly. Detected a UPS: TRIPP

Can anyone point me to information for getting the Tripplite SMART3000RM2U to work with NUT? Our newer Tripplite units seem to work with the usbhid-ups driver, but these older ones seem to need something different. So far I have had little success getting tripplite_usb to work. [root at banyan ~]# tripplite_usb -a tripplite Network UPS Tools - Tripp Lite OMNIVS / SMARTPRO driver 0.20 (2.6.1)

Hello Nut Devs, I'm working with usbhid-ups and a Tripplite OMNI1000LCD. I used a USB packet sniffer to discover something cool about the watchdog feature in this unit. (not sure if the other OMNI-X-LCD models work the same or not.) Basically there's a single HID variable at Report ID 0x52 (UPS.OutletSystem.Outlet.ffff0092) that's one byte (0-255 int) and it contains the Watchdog

He everyone, I have a Tripplite SMART700DVa using the tripplite_usb from NUT 2.5 (rev 2217) driver running in Solaris 10x86. My driver hangs when trying to connect. Once the driver sends the watchdog command ("W\0"), it can no longer receive any signals and eventually exits. The UPS responds to other watchdog commands ("W5" for example), but there doesn't seem to be

I have a TrippLite SmartPro UP (SMART3000RM2U) that shipped with the DB9 cable# 73-0866. nut doesn't recognize the UPS using the tripplite driver. I found this page: http://www.tripplite.com/support/download/PA12/help/device.htm The link lists the SmartPro series as using the cables 73-0724 or 73-0844 and the Internet 350/525 is listed as using a cable 73-0866. I have a few 73-0844s

Hi, I've been using TrippLite's PowerAlert software with my RM2200XL2U rack system and my APC BackUPS desktop systems. Unfortunately it doesn't work with openSUSE 10.2 (the software has problems with the serial port and UPS interfaces on openSUSE 10.2), so I've been looking at other options. I see that openSUSE 10.2 includes NUT, and it appears to work with my TrippLite UPS via

Thanks for your help. From: Charles Lepple <clepple at gmail.com> Date: Mon, 18 Dec 2017 19:26:56 -0500 This may sound like an apples-to-oranges comparison, but we did uncover an issue with CyberPower UPSes where the delay values needed to be greater than or equal to 60 (seconds), since they were being rounded down to integer numbers of minutes internally: What was the largest

I have a function that needs to be attached to a bunch of text fields when the page loads. I would like to use the Prototype methods that are added to DOM elements by using the $() function, but I in the function it refers to things with "this". For example, this.style.borderColor. Is there a way to extend elements from the kind of scope I am looking at? For example, is there a way to

Add the note about compatible in TODO for libblkid. Signed-off-by: Wanlong Gao <gaowanlong at cn.fujitsu.com> --- TODO | 3 +++ 1 file changed, 3 insertions(+) diff --git a/TODO b/TODO index 3955552..d604d10 100644 --- a/TODO +++ b/TODO @@ -192,6 +192,9 @@ would make more sense to just use libblkid for this. There are some places where we call out to the 'blkid' program. This