similar to: GE NetPro 3000 pinout solution

+-----------------------------------------------------------------+ | | | Black APC 940-0024C Smart Signalling UPS Cable Wiring Diagram | | This information is verified and tested to be 100% correct. | | |

Hi all! Does NUT offer any support for the GE Digital Energy NetPro 19" UPS? I have one of those beasts here, connected to a Linux machine via it's own 'serial' cable. Regards, Evert

I have a Cisco 7960 phone. I cannot seem to use the settings button to get into the phone to change the TFTP server. I've set up a DHCP Server, TFTP Server with the same address, and the phone requests the address of 0.0.0.0, the server offers the address of 192.168.2.2, but the phone seems not to take it. I have no action on the TFTP side. So, since I can't seem to server the phone

*This message was transferred with a trial version of CommuniGate(r) Pro* Greetings, aLL. There's samba-3.0.23d, running on FreeBSD-5.3 as Win2000 AD domain member. For logging user activity on share VFS module full_audit is used (with help of syslog). Logging works well, but some errors appears in log, especially when changing ACLs on share file objects from win-clients: === Nov 30

*This message was transferred with a trial version of CommuniGate(r) Pro* Greetings, All There's simple AD, running on Win2000 (realm - 0905.DN.STA, workgroup - SGNI) and samba-3.0.23d installed on FreeBSD-5.3 with ADS/LDAP/WINBIND/PAM/SYSLOG/QUOTAS/ACL. Also heimdal-0.6.3 installed. I need to join samba to domain as a AD member (with help of kerberos auth). Let's start with config files:

Hi there, all I have subj UPS, connected by USB. ups.conf: === [eaton] driver = bcmxcp_usb port = auto desc = "Eaton Powerware 9120 3000" override.battery.charge.low = 91 === upsmon.conf: === NOTIFYCMD /sbin/upssched NOTIFYFLAG LOWBATT SYSLOG+WALL+EXEC === upssched.conf === CMDSCRIPT /etc/nut/ups.sh AT LOWBATT * START-TIMER battery 3 AT ONLINE *

Operating system Windows 7 x64 NUT version 2.6.5 Windows port UPS Victron NetPro connected via serial port When I run driver when UPS cable is connected to computer's serial port it exits with following output victronups - -DDDD -a victron Network UPS Tools -GE/IMU/Victron UPS driver 0.20 (2.6.5.-3723:3731M) 0.000000 debug level is "4" 0.000000 w32_serial_open (COM1) 0.000000

Hi, I've encountered the following problem at a client. The problem results in one or more of the smbd processing continuously grabbing more and more memory until the system runs out of memory or just becomes unusable due to a low memory condition. This error is extremely serious as the entire server is eventually brought down by one error. After debugging this error at the

Hi there! I just recently got a nice new UPS to power most of my computer equipment, and having it working perfectly under NUT. However, I had a perfectly good Powercom Black Night 600AP UPS, which I'm now trying to get to power my internet gateway. Unfortuantly, due to not thinking on my part, I threw away the original serial cable. I have tried a straight - through cable, and the one

Hi all, I just got my long awaited FXS modules for a TDM400 card, and was a bit puzzled about how my phones and the FXS interface worked together. Here goes: In Sweden (that's where I am located) phones traditionally are connected in daisy chain configuration. This means that a phone in on-hook condition passes the line through back onto the outer pair of the RJ11, back into the wall

Hello all, I have obtained a Compaq T700 H UPS sans-cable. My research indicates it would've come with a HP #201092-001 cable, and from previous posts on this list, it speaks upscode2, possibly being a rebadged Eaton unit. Any suggestions for cable pinouts I can try? Regards, Mathew McBride

Hi, I have a Cisco 7960G phone for which I know the pinout of the headset socket. I have a couple of standard telephone headsets which I do not know the pinout of. I'd like to connect the two. If I have the pinout of a normal/standard headset I can rewire the ones I have to match the cisco. Thanks Mike

> Many thanks Julian. Are you looking for the pinout for a single plug 2.5mm (cellphone) headset or a dual plug 3.5mm (computer) headset? -- Nabeel Jafferali Tel: +1 (416) 628-9342 Toronto +1 (646) 225-7426 New York FWD: 46990 Email/MSN: nabeel<at>jafferali.net

I saw these adapters on eBay. 2.5mm stereo jack to modular RJ-9 jack. I think original site is http://www.ciscoheadsetadapter.com Mike >Nabeel, > I am very interested in what you came up with for a 2.5mm to RJ-10 > adapter. > >I played with every combination I could think of but the best I was able to >come up with had a echo of the far end voice back to the far end.

I am trying to test the T1 card in our legacy PBX but the connector to the card is a 15 pin serial cable. I would like to make it myself so I can try this test today. Does anyone have a pinout for it? I just made a T1 RJ-45 loop back to test my TE110P and it tested out fine. I'm trying to resolve some timing issues and a tech from Digium is going to ssh in and walk around my asterisk server

Hi I'm looking for a pinout for the above. Note this has what i'd call RJ45 sockets (or someone smart can correct me). I need to plug into BT (rj13?). And, yes I've googled (glad I'm not chinese) and have tried the suggested, just plug in a 6 connector rj11 and i didnt work atall. On a side note, I cannot beleive that Digium dont have this information on there site, it

Hi guys, just to let u known the pinout for the adapter : Adapter for connect the E1 telco lines on my digium card DB9 RJ45 3 1 8 2 2 4 6 5 Adapter used for connect the Hicom150 traditional PBX on my digium card (cross connection) DB9 RJ45 3 4 8 5 2 1

Say I had a crossover cable that connected a Mitel SX200 to a TE110P and the pinout was done as such: 1 - 4 2 - 5 5 - 1 4 - 2 (the 5 and 4 are transposed on the left side) Instead of the proper way of: 1 - 4 2 - 5 4 - 1 5 - 2 What would the results be? We have had the former as our cabling for a few months and the connection has been fine. Slip errors here and there. But we have had major

Hi Asterisk Community, I have a development with a TDM11B in it. I am trying to connect this to a exchange line as well as a UK telephone and are looking for some pinout information for the FXS port. Is it the centre 2 pins that at the tip and ring. I have been digging around the Digium site but cannot seem to pick up this info. Any help appreciated. Thanks -- Gary

I just got NUT 2.0.1 running on my Debian system at home.? I have a new CPS UPS connected via USB.? Everything is working fine, except the UPS is showing a value of 120% charged.? Any idea what causes this?? Here's the upsc output for my UPS: battery.charge: 120 battery.charge.low: 10 battery.charge.warning: 20 battery.runtime: 1320 battery.runtime.low: 300 battery.type: PbAcid