similar to: APC Back-UPS CS and ES series

On Aug 18, 2013, at 12:14 AM, Lyndon Drake wrote: > I'm happy to test an updated build, but have no idea about how to go about doing a build in the first place. Could someone help me in the process of creating a snapshot build for FreeNAS? I am not familiar with the specifics of building for FreeNAS, but our BuildBot instance is making source snapshots again:

Hello to All. OS : FreeBSD NAS 9.1-STABLE FreeBSD 9.1-STABLE [uname -a] Version : Network UPS Tools upsd 2.6.5 [upsd -V] Installation method : build into FreeNAS 9 UPS : APC Back-UPS 500 BK500EI USB Today i install FreeNAS and try to connect to it my UPS APC Back-UPS 500 BK500EI via USB with no luck;/ If anyone can try to help me I would be grateful. My configs nut.conf : MODE=standalone

Hi all ! I have a little problem using NUT from FreeNAS. Operating system FreeBSD 8.3-RELEASE-p4 (FreeNAS 8.3.0 BETA 2) UPS American Power Conversion/Back-UPS CS 650 FW:817.v7 .I USB FW:v7 NUT Driver Network UPS Tools - Generic HID driver 0.37 (2.6.5) USB communication driver 0.31 Trying to configure the UPS from FreeNAS failed so I try to investigate which is the problem. Running

Hello Charles and Douglas, I really believe that BZ2200-BR model is the same as mine BZ1200-BR, with different capacity. If you see the BZ2200-BR specs you will notice the manufacturer "APC-Microsol". Those no-breaks have a USB port in it, but in fact it is a serial<->usb cable, usually uses the port "/dev/cuaU0". In mine, the serial<->usb chip is from FTDI, and

On Mar 20, 2014, at 10:01 AM, Douglas A. Augusto wrote: > Dear NUT users/developers, > > I'm having trouble while trying to configure the UPS APC BZ2200BI-BR[1] in NUT, > which despite having a USB cable it apparently communicates using the serial > protocol. > > The relevant output of 'lsusb' is: > > Bus 002 Device 004: ID 051d:c812 American Power

Gabor: note, these HCL reports go to the nut-upsdev list. Begin forwarded message: > From: Gabor Tjong A Hung > Subject: Re: Network UPS Tools - Compatibility List > Date: September 3, 2013 2:18:31 PM EDT > > Sorry, > I just noticed the "If your device isn?t listed" part: > > [HCL] Forza FX-1500LCD supported by blazer_usb > > > [root at freenas] ~#

Folks, I've asked this question on the FreeNAS forum but there are no ideas there as it looks like it's a NUT issue. Original question: https://forums.freenas.org/index.php?threads/apc-ups-reporting-wrong-input-voltage.60888/ the nut driver is reporting the wrong input voltage. I am in the UK, 230V but it's reporting circa 108. If I connect it to the laptop and run powerchute it

Hi All, hoping someone might have some insights to what is going wrong with my NUT setup and my APC Back - UPS RS 1500 (specifically a BR1500GI) using the usbhid driver. https://download.schneider-electric.com/files?p_File_Name=AHUG-9JU4RH_R0_EN.pdf&p_Doc_Ref=SPD_AHUG-9JU4RH_EN&p_enDocType=User%20guide Main issue: NUT successfully shuts down my server when it goes on battery but when

Hi there, I’m hoping for a solution on getting my ups working in FreeNAS. Can you help me out? The driver isn’t listed and i need this to work. I’d be so grateful for anything you can do or suggest. Simon

Hi all, Sorry for the delay - three business trips abroad and LOTS of head scratching with USB Keys and DVD's of SuSE and FreeBSD... The question about the USB reports from Windows is still unanswered (I am abroad again !), but *think* the Liebert driver had been stopped. I can report the following updates for my linux setups; SuSE/FreeBSD/FreeNAS [remember here I am trying to make nut

On Feb 4, 2014, at 10:48 PM, Elliot Dierksen wrote: > NUT will complain endlessly about communication errors and never establish SNMP communication with my APC UPS Hmm, at first glance, I read the "complain endlessly" part as a figure of speech, and figured SNMP would get there eventually since it's UDP. But if you have to stop and restart NUT, that is a different story. What

Hi, I'm trying to disconnect some iSCSI targets, but can't seem to. [root at localhost ~]# iscsiadm -m session tcp: [1] 192.168.2.202:3260,1 iqn.2011.01.22.freenas.nvr:500gb tcp: [3] 192.168.2.200:3260,1 iqn.2011-2.za.co.securehosting:RAID.thin3.vg0.1tba tcp: [4] 192.168.2.202:3260,1 iqn.2011.01.22.freenas.nvr:extent0 tcp: [5] 192.168.2.200:3260,1

I have 2 APC UPS systems, one is connected to my ESXi host and the other to my FreeNAS. The battery for the FreeNAS will run out before the battery for the ESXi, so I need ESXi to shutdown first. If I wait until BatteryLow on ESXI, it will be too late as FreeNAS will have already shutdown. How can I change the configuration on ESXI to shutdown after a small delay so that it is done before

I'm trying to create a 500GB lv volume on a 500GB physical volume, but can't: [root at francois-pc ~]# pvscan PV /dev/sdd VG freenas lvm2 [500.00 GB / 500.00 GB free] PV /dev/sdc VG thecus lvm2 [1010.00 GB / 910.00 GB free] PV /dev/mapper/ddf1_RAIDp2 VG VolGroup00 lvm2 [931.25 GB / 0 free] Total: 3 [2.38 TB] / in use: 3 [2.38 TB]

I am running NUT as part of FreeNAS 9.2.0. I have looked through the manuals, but I don't see how to address my issue. The box has 4 NIC's in a LACP LAGG group. It takes a while for LACP to finish, and NUT tries to start before packets are flowing. NUT will complain endlessly about communication errors and never establish SNMP communication with my APC UPS. If I stop NUT and restart

Hi all, I’m new to NUT and have some trouble getting my new UPS to work. Since the HCL listed Powercom UHID models as „green“ I thought buying a Roline (German rebranded Powercom) model would be a good idea. The OS is FreeBSD: FreeBSD freenas-pmh.local 11.2-STABLE FreeBSD 11.2-STABLE #0 r325575+6aad246318c(HEAD): Mon Jun 24 17:25:47 UTC 2019 root at

On Sat, 11 Mar 2017 08:18:26 +0100 "Niels Dettenbach \(Syndicat IT & Internet\) via samba" <samba at lists.samba.org> wrote: > Am 11. März 2017 00:04:13 MEZ schrieb Andrew Walker via samba > <samba at lists.samba.org>: > >I don't believe that ZFS on FreeBSD supports acltype=posixacl and > >sa-based > > If you want to see a working samba / zfs

RPvs> On Tue, 1 Jan 2019 10:35:17 -0800 RPvs> Gregory Sloop via samba <samba at lists.samba.org> wrote: >> I'm working to put up a production FeeeNAS box tied to Samba/AD for >> authentication for users connecting to the FreeNAS share(s). In >> joining FreeNAS to the AD domain, one immediately runs into >> "problems" with TLS/encryption. RPvs>

Hello;I just came across NUT, testing FreeNAS/FreeBSD. I?m running at home a APC UPS connected to another computer, running apcupsd. I found out that NUT didn't talk by default to apcupsd, and there was a driver created relatively recently (apcupsd-ups), which filled in that gap. The version I found on my FreeBSD/FreeNAS system seems to imply that there is more to come to that driver (0.04)

On 2/5/2014 8:24 AM, Charles Lepple wrote: > On Feb 4, 2014, at 10:48 PM, Elliot Dierksen wrote: > >> NUT will complain endlessly about communication errors and never establish SNMP communication with my APC UPS > Hmm, at first glance, I read the "complain endlessly" part as a figure of speech, and figured SNMP would get there eventually since it's UDP. But if you have