similar to: FreeNAS configuration command

On Mar 20, 2014, at 10:01 AM, Douglas A. Augusto wrote: > Dear NUT users/developers, > > I'm having trouble while trying to configure the UPS APC BZ2200BI-BR[1] in NUT, > which despite having a USB cable it apparently communicates using the serial > protocol. > > The relevant output of 'lsusb' is: > > Bus 002 Device 004: ID 051d:c812 American Power

Dear NUT users/developers, I'm having trouble while trying to configure the UPS APC BZ2200BI-BR[1] in NUT, which despite having a USB cable it apparently communicates using the serial protocol. The relevant output of 'lsusb' is: Bus 002 Device 004: ID 051d:c812 American Power Conversion The device is registered as /dev/ttyACM0 and uses the kernel module 'cdc_acm' (USB

Hello Charles and Douglas, I really believe that BZ2200-BR model is the same as mine BZ1200-BR, with different capacity. If you see the BZ2200-BR specs you will notice the manufacturer "APC-Microsol". Those no-breaks have a USB port in it, but in fact it is a serial<->usb cable, usually uses the port "/dev/cuaU0". In mine, the serial<->usb chip is from FTDI, and

On Jul 30, 2013, at 10:39 AM, Pavel Potcheptsov (EKTOS) wrote: > Is this a trouble? Driver use path /var/state/ups/ but upsd use path /var/db/nut/upsd.pid Yes, the driver and upsd need to agree on the path to the socket. From the FreeBSD ports tree: /usr/ports/sysutils/nut/Makefile: STATEDIR?= /var/db/nut [...] CONFIGURE_ARGS= --sysconfdir=${PREFIX}/etc/nut \

# reboot Connection to 192.168.5.81 closed by remote host. Connection to 192.168.5.81 closed. ppo at admin:/tmp$ ssh root at 192.168.5.81 root at 192.168.5.81's password: Last login: Tue Jul 30 14:10:49 2013 from pc-ppo.kh.ektos OpenBSD 5.3 (GENERIC.MP) #58: Tue Mar 12 18:43:53 MDT 2013 # ps -aux | grep ups root 2254 0.0 0.0 324 700 p0 S+ 5:29PM 0:00.00 grep ups # ps -aux

Dear friends, I installed NUT and followed all suggested procedures to verify if my ups is supported. No driver recognized my ups, and the genericups tests get wrong. Here I send some informations about it: The ups model is APC BZ1200-BR I use Ubuntu, and the lsusb results Bus 003 Device 003: ID 0403:6001 Future Technology Devices International, Ltd FT232 USB-Serial (UART) IC for ups. The

Model: Tripp-lite OMNIVS1500 Error: Network UPS Tools - UPS driver controller 2.2.1- Network UPS Tools - Tripp Lite OMNIVS and SMARTPRO driver 0.11 (2.2.1-) Warning: This is an experimental driver. Some features may not function correctly. Detected a UPS: unknown/unknown libusb_set_report() returned -1 instead of 8 Could not reset watchdog. Please send model information to nut-upsdev mailing

- Charles > On Oct 16, 2016, at 3:34 AM, Daniel Shields <grungelizard9 at hotmail.com> wrote: > > I've been testing with debug further and there's a few extra lines when the nut-server stops communicating as opposed to when it's running. > > > Backtrace after stale data, UPS nailbunny at localhost is unavailable: > Sorry to take a while to get back to you

Thank You for You reply, Charles D?a 07.10.2017 o 14:30 Charles Lepple nap?sal(a): > Is the "lan4.1" cable different from this one? > http://networkupstools.org/cables.html#_tripp_lite Yes, it is different. The correct cable for this interface version looks like this: http://pinouts.ru/UPS/tripplite_smartpro_cable_pinout.shtml > Are you comfortable with rebuilding the

I?m wondering if what I have done is good : # get the source from github on my computer # autogen.sh # name=nut # ./configure --prefix=/ --sysconfdir=/etc/$name --mandir=/usr/share/man --libdir=/usr/lib --includedir=/usr/include --datadir=/usr/share/$name --with-statepath=/var/run/nut --with-altpidpath=/var/run/nut --with-drvpath=/lib/nut --with-pidpath=/var/run/$name

Hi Arnaud & Charles, You?ll have to forgive my low level of Linux Understanding here?. I downloaded the source files, modified the appropriate driver file, re-compiled it (all of this was a lot of research and learning!) When I use the new driver I get ? Network UPS Tools - UPS driver controller 2.7.2 Network UPS Tools - MGE UPS SYSTEMS/U-Talk driver 0.93 (2.7.4.1) Can't chdir to

I've been wanting to build the trunk since Arjen added the powerpanel driver... been having a little trouble... after running these commands: /usr/local/libexec/automake19/aclocal -I m4 /usr/local/libexec/autoconf259/autoheader /usr/local/libexec/automake19/automake -ac /usr/local/libexec/autoconf259/autoconf ./configure --with-cgi --with-user=nutmon

On Tue, Mar 09, 2010 at 07:14:59PM -0500, Charles Lepple wrote: > On Mar 9, 2010, at 5:54 PM, Kelvin Ku wrote: > >> However, if I try to run usbhid-ups as user "nut", I get: >> >> $ sudo -u nut ./usbhid-ups -a usb > [...] >> Whereas if I run it as root: >> >> $ sudo ./usbhid-ups -a usb -u root > > Did you pass "--with-user=nut"

Got the: git clone git://github.com/networkupstools/nut.git To work. Had to all so do this: apt-get install autoconf apt-get install libtool Did put driver = usbhid-ups in the /etc/nut/ups.conf file like you said. Here is what I got for it all: root at odroid-u2:~/nut# ./autogen.sh Calling autoreconf... libtoolize: putting auxiliary files in AC_CONFIG_AUX_DIR, `.'. libtoolize: copying

To avoid bitrot, any new feature needs testsuite coverage ;) Still to come: once I get my work on parallel nbd finished, I will add a test-parallel-nbd.sh that closely mirrors what my other series added in test-parallel-file.sh. If desired, it might be a fun exercise to tweak test-nbd into using a for-loop of user-controlled depth for how deep you want to nest the forwarding tree, to see where

Thanks Dan and Charles - I've found the usb passthrough will be a non-starter (not supported on my host). Dan - is your recommendation to build Nut from source or just the driver? I'm trying to build the whole project but am obviously missing dependencies... I've come across a configure error syntax error near unexpected token `CPPUNIT,' which I've seen in a previous

On Jul 31, 2013, at 9:07 AM, James HORLEY wrote: > I?m wondering if what I have done is good : > # get the source from github on my computer > # autogen.sh > # name=nut > # ./configure --prefix=/ --sysconfdir=/etc/$name --mandir=/usr/share/man > --libdir=/usr/lib --includedir=/usr/include --datadir=/usr/share/$name > --with-statepath=/var/run/nut

[As posted as Ubuntu Question #184284 on Launchpad] Hi, I try to set up nut (2.4.3) on my Lucid (10.04.3 LTS) to make use of my old but very trusty UPS (Best Power Fortress 660 LI). Yes, this UPS is old (about 16 years), but with its third battery pack last week it is as good as new. It runs perfectly well with Windows XP, Vista and even Windows 7. But not so with Ubuntu and nut. After

On Aug 18, 2013, at 12:14 AM, Lyndon Drake wrote: > I'm happy to test an updated build, but have no idea about how to go about doing a build in the first place. Could someone help me in the process of creating a snapshot build for FreeNAS? I am not familiar with the specifics of building for FreeNAS, but our BuildBot instance is making source snapshots again:

Hi, Just started using NUT with a Liebert PSI-XR 3000 with an Intellislot web card. It seems I can't get it to run properly. I am using NUT 2.6.0 built from source on Ubuntu 8.0.4 . My build parameters are : ./configure --enable-strip --with-linux-hiddev=/usr/include/linux/hiddev.h --with-udev-dir=/lib/udev \ --prefix=/usr \ --exec-prefix=/ \ --sysconfdir=/etc/nut \