similar to: Question on support for Upsonic Commercial UPS CXR 2000 - 2000VA/1200W - Rack/Tower on Freebsd 9.1.

On Jan 31, 2014, at 3:14 PM, Chris Duffy wrote: > The current one I am looking is support for: > > Upsonic Commercial UPS CXR 2000 - 2000VA/1200W - Rack/Tower > > What seems to be supported in Freebsd is: Small clarification: the hardware compatibility list isn't broken down by operating system (theoretically, the drivers should work on any POSIX system, with additional

Thx for the info Charles. Here is what I am seeing from 'usbconfig list' ugen0.1: <EHCI root HUB Intel> at usbus0, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE ugen1.1: <EHCI root HUB Intel> at usbus1, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE ugen0.2: <product 0x0024 vendor 0x8087> at usbus0, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=SAVE ugen1.2: <product 0x0024 vendor

On Feb 3, 2014, at 9:05 PM, Chris Duffy wrote: > Thx for the info Charles. > > Here is what I am seeing from > 'usbconfig list' [...] > ugen1.3: <USB UPS PPC> at usbus1, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON > > > The last line I guess is key. Unfortunately, it is not very unique: the vendor can pick the string "USB UPS PPC", but the drivers

Charles, Here is the output: ugen1.3: <USB UPS PPC> at usbus1, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON bLength = 0x0012 bDescriptorType = 0x0001 bcdUSB = 0x0200 bDeviceClass = 0x0000 bDeviceSubClass = 0x0000 bDeviceProtocol = 0x0000 bMaxPacketSize0 = 0x0008 idVendor = 0x06da idProduct = 0x0005 bcdDevice = 0x0003 iManufacturer = 0x0003 <PPC>

On 2/5/14, 9:55 PM, Charles Lepple wrote: > On Feb 5, 2014, at 9:03 PM, Chris Duffy wrote: > >>> Please run this: >>> >>> /usr/local/libexec/nut/blazer_usb -a UPSonic -u root -D >>> >>> and send the output back to the list. >>> >> Output from the above command: >> >> 0.000000 debug level is '1' >>

Charles, the out from the command below as well as the system.log file are below your email. It does look like a permission issue but what one? Thx chris On 2/5/14, 6:43 PM, Charles Lepple wrote: > On Feb 5, 2014, at 10:12 AM, Chris Duffy wrote: > >> However, we are using NUT 2.6.5. >> >> Are we missing something by running 2.6.5 rather then >> 2.7.1? If so, I

Charles, We run everything as "root" :) However, we are using NUT 2.6.5. Are we missing something by running 2.6.5 rather then 2.7.1? If so, I can build/install 2.7.1. Thx chris Would On 2/4/14, 9:05 PM, Charles Lepple wrote: > On Feb 4, 2014, at 9:05 AM, Chris Duffy wrote: > >> ugen1.3: <USB UPS PPC> at usbus1, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON > [...]

On Feb 4, 2014, at 9:05 AM, Chris Duffy wrote: > ugen1.3: <USB UPS PPC> at usbus1, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON [...] > idVendor = 0x06da > idProduct = 0x0005 This VID:PID combination should be handled by blazer_usb. In NUT 2.7.1 and later, this would be covered by nutdrv_qx as well. > I am running all the ups programs as root, i.e. "ps -aux" shows:

Charles, here is the command(s) output using uhidd.... # uhidd -v -u /dev/ugen1.3ugen1.3[0]-> HID interface ugen1.3[0]-> Report descriptor size = 27 ugen1.3[0]-> Kernel driver is active ugen1.3[0]-> kernel driver detached! ugen1.3[0]-> Find IN interrupt ep: 0x81 packet_size=0x8 # /usr/local/libexec/nut/blazer_usb -a UPSonic -u root -DDDD 0.000000 debug level is

On Feb 5, 2014, at 9:03 PM, Chris Duffy wrote: >> Please run this: >> >> /usr/local/libexec/nut/blazer_usb -a UPSonic -u root -D >> >> and send the output back to the list. >> > Output from the above command: > > 0.000000 debug level is '1' > 0.248714 Supported UPS detected with megatec protocol > 1.268575

On Feb 6, 2014, at 8:41 AM, Chris Duffy wrote: > 0.016485 Trying megatec protocol... > 0.017411 send: Q1 > 0.252545 read: (244.4 244.4 229.9 028 50.0 2.19 23.1 00000001 > 0.252589 Status read in 1 tries > 0.252602 Supported UPS detected with megatec protocol > 1.288032 send: Unknown error > 1.288085 Permissions problem: Input/output error

Thx Charles, So since this is a new type of UPSonic UPS, do you think the vendor screwed up or is it just some quirk on Freebsd? Yes, if you can look into this I would appreciate it. I do not see anyone else on the Web attempting to use this new device yet.....but....... Regards chris On 2/6/14, 8:24 AM, Charles Lepple wrote: > On Feb 6, 2014, at 8:41 AM, Chris Duffy wrote: > >>

On Feb 5, 2014, at 10:12 AM, Chris Duffy wrote: > However, we are using NUT 2.6.5. > > Are we missing something by running 2.6.5 rather then > 2.7.1? If so, I can build/install 2.7.1. Well, 2.6.5 is from August 2012, so it's not the newest. And eventually, we would like people to switch to the shiny new nutdrv_qx driver which is in 2.7.1. But I'm pretty much guessing here

On Feb 6, 2014, at 9:33 AM, Chris Duffy wrote: > So since this is a new type of UPSonic UPS, do you think > the vendor screwed up or is it just some quirk on Freebsd? It's a pretty fundamental design flaw, although it isn't uncommon among USB devices aimed at the Windows market, and to their credit, it does make implementation and deployment simpler on Windows. Neither the FreeBSD

I am having problems with mouse, keyboard and APC UPS. When attempting to start apcupsd I get the following error: Jan 8 17:42:06 Ace apcupsd[1606]: apcupsd FATAL ERROR in generic-usb.c at line 636 Cannot find UPS device -- For a link to detailed USB trouble shooting information, please see <http://www.apcupsd.com/support.html>. Jan 8 17:42:06 Ace apcupsd[1606]: apcupsd error shutdown

On 7/9/07, Arnaud QUETTE <Arnaud.QUETTE at mgeups.com> wrote: > > My UPS is a: Upsonic CXR1000 (made in Oz, probably rebranded > monitoring) > > Driver: Megatec > > > > Works perfectly! [snip] > I'll add your model to the supported ones once Carlos has validated > everything is fine. I can do that.

Hi, I recently installed a Upsonic PrOffice 650 UPS, which is a cheap model[1] available in Australia. It has a serial and USB port, and comes with a note saying WinPower software can be downloaded from [2]. Investigation of the software shows it to be Java with native libraries for serial and USB. Disassembling various classes reveals it talks at 2400 baud, and has a protocol similar to

Hi all, I've bought myself a Upsonic Power Proffice 650 (Pro Office on the compliance sticker :-/) and can't work our which nut ups driver it requires. Product Brouchure: http://upsonic.com.au/pdf/proffice.pdf George

Hi Heinz, 2010/5/30 heinz > Thank you for your nut-2.4.3 system. I had big troubles getting it to work > with the UPSONIC PROFFICE 650 UPS in USB mode. > > I had to rewrite the get_data_phoenix() function in drivers/megatec_usb.c > file. > It now appears to be working correctly. I have attached the source of the > modified function in case you might want to add it to a

For an Xray file system patients have folders and folders have studies. That is: patients folders studies id id id name patient_id folder_id ... label type ... ... The list of studies with their associated folder and patient might look like this: name folder_label study_type