similar to: bcmxcp - Powerware 9125

Hi, just through setting up nut-2.0.2 I ran into a shutdown problem. As I have already spend some time on it and don't know any further, I like to ask for advice. Situation: Powerware 9125 serially connected using /dev/cua0 nut compiled and installed fine system shall - broadcast a message and shut down if ups on battery for 30+ s - wait 120 s - broadcast another message - give system 120

Hello! It looks like bcmxcp driver doesn't fit my device: UPS Model ? ? ? ? ? ? ? ? ? ?PW9125 UPS Firmware Version ? ?FP: 1.10 INV: 1.10 VA Rating ? ? ? ? ? ? ? ? ? ? ?3000 VA Web/SNMP card is present. Minicom connection to /dev/ttyS0 gives nice banner and control menu, but they prevent nut driver from working correctly (I guess). UPS should be switched into "Pass-Through" mode

Hello! It looks like bcmxcp driver doesn't fit my device: UPS Model ? ? ? ? ? ? ? ? ? ?PW9125 UPS Firmware Version ? ?FP: 1.10 INV: 1.10 VA Rating ? ? ? ? ? ? ? ? ? ? ?3000 VA Web/SNMP card is present. Minicom connection to /dev/ttyS0 gives nice banner and control menu, but they prevent nut driver from working correctly (I guess). UPS should be switched into "Pass-Through" mode

Hi, I have an HP R5500XR and a Compaq R3000XR that I would like to use with nut. I searched the compatibility lists and the mail list archives but couldn't find anything. They both have 9 pin serial ports. Can anyone give me any information about them, and if they are supported by nut? Thanks, Denny Fox

2012/2/6 thomas schorpp <thomas.schorpp at googlemail.com>: > Hi, Hi Thomas, > I want the driver report the battery status from ABM charging controllers > -patch attached- : thanks for your patch. since it introduces a new variable (battery.status.abm), I prefer to step back and think to something useful more widely. thus, I'm thinking about a generic

I'm trying to get a Powerware 5125 UPS running using the bcmxcp driver, but I get the following errors: video2:~# /sbin/upsdrvctl start Network UPS Tools - UPS driver controller 2.0.4 Network UPS Tools - BCMXCP UPS driver 0.10 (2.0.4) Communications with UPS lost: Error executing command Communications with UPS lost: Error executing command Communications with UPS lost: Error executing

Greetings, I have been using the bcmxcp_usb driver heavily over the last two years as part of a very successful product, first from NUT 2.4.1 and now from NUT 2.6.0. Now I have a need to do setvar of the outlet.n.delay.start variables, so recently I modified bcmxcp.c to do that. I've tested it and it works well for my purposes. My plans are to begin shipping that modified driver as part

Hi, Am 13.02.2012 um 18:58 schrieb Arnaud Quette: > 2012/2/6 thomas schorpp <thomas.schorpp at googlemail.com>: >> Hi, > > Hi Thomas, > >> I want the driver report the battery status from ABM charging controllers >> -patch attached- : > > For now, I've tracked your patch here: >

Hi Here is a very minor patch for the bcmxcp.c driver, mainly fixing the function name used in debug statement, and at the same time fix indentation. Regards Alf Hogemark From 86c7940d0ea11b5b38a7f4518095ee2428d658c7 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Alf=20H=C3=B8gemark?= <alf at i100.no> Date: Mon, 1 Jul 2013 21:11:40 +0200 Subject: [PATCH] bcmxcp: Fix method name outputted in

I have setup nut-2.4.1 with the bcmxcp driver for my HP R3000 XR unit and although it appears to work, I receive the following sorts of errors in syslog: Aug 27 10:33:05 sv18 bcmxcp[6373]: Communications with UPS lost: Receive error (data): got 0 bytes instead of 64!!! Aug 27 10:33:15 sv18 bcmxcp[6373]: Communications with UPS lost: Receive error (data): got 0 bytes instead of 64!!! Aug 27

Hi I have the following UPS : ups.mfr: Eaton ups.model: POWERWARE UPS 500i ups.power.nominal: 500 It is using the bcmxcp_usb driver. I started the driver with debug options, and noticed the following for the meter map : 0.475625 0027 0000 51 output.frequency 0.475634 0028 0004 51 input.frequency 0.475641 0033 0008 51 battery.voltage

Hi Inspired by the changes by Prachi Gandhi to use the command map from the UPS in the bcmxcp driver, I think the map should be used, if available, to control all commands the driver adds using "dstate_addcmd". The following patch is an attempt at doing so. The patch is against the bcmxcp branch. Since my UPS also supports : #define PW_UPS_ON (unsigned char)0x89 /* UPS on

On Jul 2, 2013, at 5:16 PM, Kjell Claesson wrote: >> I hope other people can also test this. >> >> Regards >> Alf Hogemark > > Due to some crashes on the disks and lack of time I don't have the git on the > pc now. But maybe some other can commit this. I'd like to ask people to specifically try the bcmxcp branch on GitHub - it includes some changes

Hi Michael, I've forwarded your patch to Kjell, who's maintaining the bcmxcp driver, and to the nut development list. Kjell and others have more knowledges of the xcp protocol and will be able to analyze your patch. 2008/1/4, michalwd1979 <michalwd1979 at o2.pl>: > Hello Arnaud, > I am sending You a small patch to bcmxcp.c and bcmxcp.h files from nut-2.2.0. I written this

On Sep 19, 2014, at 4:03 PM, Nello Lucchesi <nello at octobergroup.com> wrote: > I'm looking for a driver for and old uninterruptible power supply (UPS), Eaton Powerware 9125 2500U. I want to use it with my FreeNAS server. > > I looked a the list and didn't see a driver for it: > > http://www.networkupstools.org/stable-hcl.html?manufacturer=Eaton > > I see a

Hi, Got this mail. It looks like he has a ups with revision before K, and need another startup. The 'PW_SET_REQ_ONLY_MODE' is not implemented, so to make it work we have to follow the protocol and send a 'PW_ID_BLOCK_REQ'. This in comsetup of bcmxcp_ser.c Also the standard id block ends with 'Statistics Map', so we have to Skip after reading the length of the 'Size

tisdagen den 2 juli 2013 20.24.47 skrev Alf H?gemark: > Hi > Hi Alf, > I have the following UPS : > ups.mfr: Eaton > ups.model: POWERWARE UPS 500i > ups.power.nominal: 500 > > It is using the bcmxcp_usb driver. > > I started the driver with debug options, and noticed the following for > the meter map : > > 0.475625 0027 0000 51

I ran into a portability issue with drivers/bcmxcp.c in nut-2.4.1 on my UnixWare 7.1.4 machine. The error I get is ..... UX:acomp: ERROR: "/opt/src/utils/nut-2.4.1/drivers/bcmxcp.c", line 835: integral constant expression expected ..... Looking at the code we see ..... int init_outlet(unsigned char len) { unsigned char answer[len]; ..... Although gcc can handle it, it's not

I'm looking for a driver for and old uninterruptible power supply (UPS), Eaton Powerware 9125 2500U. I want to use it with my FreeNAS server. I looked a the list and didn't see a driver for it: http://www.networkupstools.org/stable-hcl.html?manufacturer=Eaton I see a driver for the 9130; any idea whether it will work with a 9125? Any other ideas for connecting the 9125 to a FreeNAS

UPS: HP R3000 XR with HP UPS Management Module What I Want: I just want the UPS to shut down the client called "tor" before the UPS power drains out, I'd prefer to use a direct serial cable instead of network, in case the network doesn't work. I'll manage the UPS trough the ethernet using the built-in HTTP webinterface in the HP UPS Management Module. I've created a